Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM27L0U _59 Vehicle Exterior _049351 WIPER / WASHER _0235980 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WIPER SWITCH

U154015E02
1.323,2.729 0.344,2.063 false 1.021,2.74 0.333,2.448 false 0.708,2.885 0.333,3.042 false 1.615,2.729 1.708,2.156 false 2.188,2.729 2.042,2.156 false 2.448,2.729 2.865,2.156 false 2.313,3.792 2.177,3.188 false 1.521,3.781 1.625,3.177 false 2.844,3.792 2.354,3.125 false 0.073,0.063 2.563,0.427 2.49,0.365 10 false Component without harness connected: (Wiper Switch) 1.167,1.771 1.281,1.917 0.115,0.146 10 false B 2.375,1.771 2.49,1.927 0.115,0.156 10 false A 0.104,2.958 0.302,3.115 0.198,0.156 10 false +2 0.135,2.354 0.313,2.521 0.177,0.167 10 false +1 0.115,1.969 0.313,2.125 0.198,0.156 10 false +B 1.635,2 1.854,2.177 0.219,0.177 10 false +S 1.354,3.813 1.625,3.99 0.271,0.177 10 false WR 1.927,1.99 2.188,2.167 0.26,0.177 10 false WF 2.802,1.99 3.073,2.156 0.271,0.167 10 false EW 2.156,3.813 2.448,3.99 0.292,0.177 10 false +1R 2.677,3.802 2.979,3.979 0.302,0.177 10 false C1R

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
B-2 (+B) - B-3 (+1) MIST Below 1 Ω
B-1 (+S) - B-3 (+1) OFF Below 1 Ω
B-1 (+S) - B-3 (+1) INT Below 1 Ω
B-2 (+B) - B-3 (+1) LO Below 1 Ω
B-2 (+B) - B-4 (+2) HI Below 1 Ω


If the result is not as specified, replace the wiper switch.

Standard Resistance:
Front Washer Switch
Tester Connection Switch Condition Specified Condition
A-2 (EW) - A-3 (WF) OFF 10 kΩ or higher
A-2 (EW) - A-3 (WF) ON Below 1 Ω


If the result is not as specified, replace the wiper switch.

Standard Resistance:
Rear Wiper and Washer Switch
Tester Connection Switch Condition Specified Condition
A-2 (EW) - B-5 (WR) WASH (Rear wiper switch OFF) Below 1 Ω
A-2 (EW) - B-5 (WR)
A-2 (EW) - A-7 (+1R)
OFF 10 kΩ or higher
A-2 (EW) - A-6 (C1R) INT-LO Below 1 Ω
A-2 (EW) - A-7 (+1R) ON-HI Below 1 Ω
A-2 (EW) - B-5 (WR)
A-2 (EW) - A-7 (+1R)
A-7 (+1R) - B-5 (WR)
WASH (Rear wiper switch ON) Below 1 Ω


If the result is not as specified, replace the wiper switch.



b.

Check the intermittent operation.

i.

Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector.


ii.

Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 2 (EW) of the A connector and 1 (+S) of the B connector.


iii.

Turn the wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 1 (+S) of the B connector for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 1 (+S) of the B connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

Standard:

Refer to the illustration below.


E146261E06
0.052,0.448 1.594,1.104 1.542,0.656 10 false Voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector 1.802,0.594 2.469,0.74 0.667,0.146 10 false 11 to 14 V 2.188,1.052 2.458,1.208 0.271,0.156 10 false 0 V 2.396,1.448 3.604,1.615 1.208,0.167 10 false 0.6 to 2.6 seconds 1.969,0 4.01,0.5 2.042,0.5 10 false FAST: Connect the negative (-) battery terminal cable to terminal 1 (+S) of the B connector 4.292,0 6.365,0.323 2.073,0.323 10 false SLOW: Connect battery negative lead to terminal B-1 (+S) 4.573,1.438 5.885,1.594 1.313,0.156 10 false 5.7 to 15.7 seconds

If the result is not as specified, replace the windshield wiper switch.



c.

Check the operation (front washer).

i.

Turn the wiper switch off.


ii.

Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 1 (+S) of the B connector and 2 (EW) of the A connector.


iii.

Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector. Turn the washer switch on and off, and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

Standard:

Refer to the illustration below.


E106382E21
3.198,1.177 3.198,1.292 false 3.865,1.177 4.156,1.313 false 1.219,0.396 2.365,0.594 1.146,0.198 10 false Washer Switch 0.115,0.781 2.229,1.313 2.115,0.531 10 false Voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector 2.802,0.313 3.083,0.51 0.281,0.198 10 false ON 2.729,0.542 3.115,0.74 0.385,0.198 10 false OFF 2.354,0.76 3.177,0.958 0.823,0.198 10 false 11 to 14 V 2.781,0.99 3.104,1.188 0.323,0.198 10 false 0 V 2.563,1.302 3.854,1.667 1.292,0.365 10 false Approximately 0.3 seconds 3.865,1.302 5.792,1.76 1.927,0.458 10 false Approximately 2.2 seconds

If the result is not as specified, replace the windshield wiper switch.