Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM27L0U _59 Vehicle Exterior _049352 LIGHTING (EXT) _0235988 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU receives a front fog light switch information signal from the light control switch (front fog switch), and illuminates the front fog lights.

WIRING DIAGRAM

E176436E05
0.313,1.042 1.427,1.375 1.115,0.333 10 false from TAIL Relay 0.552,1.5 1.365,1.854 0.813,0.354 10 false from Battery 2.031,1.646 2.5,1.99 0.469,0.344 10 false FOG 3.979,1.854 4.323,2.073 0.344,0.219 10 false FOG 5.854,1.063 6.281,1.281 0.427,0.219 10 false FFGO 2.573,1.188 3.115,1.521 0.542,0.333 10 false TAIL 3.656,1.177 3.823,1.333 0.167,0.156 10 false 1 2.292,2.51 2.458,2.667 0.167,0.156 10 false 1 3.146,3.875 3.313,4.031 0.167,0.156 10 false 1 4.521,1.188 4.646,1.344 0.125,0.156 10 false 2 2.646,2.5 2.771,2.656 0.125,0.156 10 false 2 3.5,3.875 3.625,4.031 0.125,0.156 10 false 2 3.656,1.635 3.813,1.813 0.156,0.177 10 false 3 4.521,1.635 4.635,1.781 0.115,0.146 10 false 5 5.802,2.969 6.802,3.313 1,0.344 10 false Main Body ECU 5.802,2.802 6.021,2.979 0.219,0.177 10 false H4 2.583,4.042 2.885,4.188 0.302,0.146 10 false A37 1.813,2.688 2.115,2.833 0.302,0.146 10 false A36 2.583,4.208 4.146,4.563 1.563,0.354 10 false Front Fog Light Bulb RH 1.813,2.854 3.406,3.188 1.594,0.333 10 false Front Fog Light Bulb LH 5.667,1.167 5.781,1.313 0.115,0.146 10 false 4

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT FOG LIGHT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test / Front Fog Light.


e.

Check that the front fog lights turn on/off.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Front Fog Light Relay Front fog light ON or OFF -

OK:

Front fog lights turn on/off.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FUSE (FOG)
2.INSPECT FUSE (FOG)
a.
E161570E10
1.281,2.677 1.865,4.125 true 0.156,0.333 1.99,0.563 1.833,0.229 10 false Engine Room Relay Block: 1.677,4.146 2.021,4.302 0.344,0.156 10 false FOG

Remove the FOG fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FOG fuse Always Below 1 Ω



c.

Reinstall the FOG fuse.



OK

3.INSPECT FOG LIGHT BULB

NG

REPLACE FUSE

3.INSPECT FOG LIGHT BULB
a.

Temporarily replace the front fog light bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the front fog light turn on.

OK:

front fog light turn on.




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT BULB - BATTERY)
4.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT BULB - BATTERY)
U153965E01
0.072,0.033 2.444,0.398 2.372,0.365 10 Front view of wire harness connector: (to Front Fog Light Bulb) 0.269,1.881 0.588,2.048 0.319,0.166 10 A36 0.269,2.507 0.588,2.674 0.319,0.166 10 A37 0.765,1.882 0.938,2.045 0.173,0.162 10 *1 0.773,2.514 0.943,2.676 0.169,0.162 10 *2 2.726,2.518 3.151,2.667 0.425,0.148 10 *1: LH 2.726,2.856 3.172,3.005 0.446,0.148 10 *2: RH

a.

for LH:

i.

Disconnect the A36 front fog light LH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-2 - Body ground Light control switch TAIL, front fog light switch ON 11 to 14 V
Light control switch TAIL, front fog light switch OFF Below 1 V



iii.

Reconnect the front fog light LH connector.



b.

for RH:

i.

Disconnect the A37 front fog light RH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A37-2 - Body ground Light control switch TAIL, front fog light switch ON 11 to 14 V
Light control switch TAIL, front fog light switch OFF Below 1 V



iii.

Reconnect the front fog light RH connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT FOG LIGHT BULB - BODY GROUND)

NG

5.INSPECT FOG LIGHT RELAY (FOG)
5.INSPECT FOG LIGHT RELAY (FOG)
E121182E12
1.724,1.093 1.835,1.242 0.111,0.149 10 5 1.788,0.036 1.899,0.185 0.111,0.149 10 1 3.168,0.122 3.279,0.271 0.111,0.149 10 2 1.69,1.712 1.800,1.860 0.111,0.149 10 3 1.312,1.428 1.422,1.577 0.111,0.149 10 3 1.299,0.878 1.409,1.027 0.111,0.149 10 2 0.353,0.874 0.464,1.023 0.111,0.149 10 1 0.362,1.424 0.473,1.573 0.111,0.149 10 5 1.862,1.183 2.269,1.084 false 2.269,1.583 1.806,1.785 false 2.14,0.624 1.857,0.225 false 2.764,0.533 3.168,0.242 false

a.

Remove the FOG relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
When battery voltage is applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall the FOG relay.



OK

6.CHECK HARNESS AND CONNECTOR (FOG RELAY - BATTERY, TAIL RELAY)

NG

REPLACE FOG RELAY

6.CHECK HARNESS AND CONNECTOR (FOG RELAY - BATTERY, TAIL RELAY)
U154010E02
0.042,0.031 1.948,0.469 1.906,0.438 10 false Component without relay: (Engine Room Relay Block) 1.802,1.094 2.563,1.354 0.76,0.26 10 false FOG Relay

a.

Remove the FOG relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FOG relay terminal 1 - Body ground Light control switch TAIL 11 to 14 V
FOG relay terminal 3 - Body ground Always 11 to 14 V



c.

Reinstall the FOG relay.



OK

7.CHECK HARNESS AND CONNECTOR (FOG RELAY - FRONT FOG LIGHT BULB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FOG RELAY - FRONT FOG LIGHT BULB)
a.

Remove the FOG relay from the engine room relay block.

E344949E01
3.99,1.438 4.344,1.698 0.354,0.26 4,1.875 4.354,2.135 0.354,0.26 1.979,2.146 2.49,1.969 false 0.208,0.146 1.938,0.583 1.729,0.438 10 false Component without relay: (Engine Room Relay Block) 2.552,1.875 3.385,2.135 0.833,0.26 10 false FOG Relay 4.177,0.146 6.531,0.635 2.354,0.49 10 false Front view of wire harness connected: (to Front Fog Light Bulb) 4.052,1.479 4.448,1.708 0.396,0.229 10 false A36 4.052,1.917 4.448,2.146 0.396,0.229 10 false A37 4.417,1.479 4.656,1.708 0.24,0.229 10 false *1 4.417,1.906 4.656,2.135 0.24,0.229 10 false *2 5.948,1.74 6.417,1.969 0.469,0.229 10 false *1: LH 5.958,2.073 6.427,2.302 0.469,0.229 10 false *2: RH


b.

for LH:

i.

Disconnect the A36 front fog light LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FOG relay terminal 5 - A36-2 Always Below 1 Ω
FOG relay terminal 5 - Body ground Always 10 kΩ or higher



iii.

Reconnect the front fog light LH connector.



c.

for RH:

i.

Disconnect the A37 front fog light RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FOG relay terminal 5 - A37-2 Always Below 1 Ω
FOG relay terminal 5 - Body ground Always 10 kΩ or higher



iii.

Reconnect the front fog light RH connector.



d.

Reinstall the FOG relay.



OK

8.CHECK HARNESS AND CONNECTOR (FOG RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (FOG RELAY - MAIN BODY ECU)
U154008E02
0.531,3.052 1.844,2.323 true 0.063,0.052 2.448,0.406 2.385,0.354 10 false Front view of wire harness connector: 1.594,1.365 1.823,1.521 0.229,0.156 10 false H4 0.313,3.083 0.74,3.229 0.427,0.146 10 false FFGO

a.

Disconnect the H4 main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H4-4 (FFGO) - Body ground Light control switch TAIL 11 to 14 V



c.

Reconnect the main body ECU connector.



OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR