Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM27L0U _59 Vehicle Exterior _049352 LIGHTING (EXT) _0235988 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Signal Circuit  


DESCRIPTION

The main body ECU receives a headlight Lo switch information signal from the light control switch, and illuminates the headlight low beam.

WIRING DIAGRAM

E163640E04
0.802,1.009 1.618,1.177 0.816,0.168 10 from Battery 3.907,1.833 4.322,1.994 0.415,0.161 10 HEAD 3.633,0.927 3.738,1.094 0.105,0.168 10 1 3.631,1.4 3.727,1.546 0.096,0.146 10 3 4.518,0.925 4.621,1.085 0.103,0.160 10 2 4.52,1.383 4.637,1.526 0.117,0.143 10 5 5.258,1.038 5.495,1.180 0.237,0.143 10 DB 5.279,0.865 5.465,1.020 0.187,0.155 10 18 5.763,2.79 6.785,2.964 1.022,0.174 10 Main Body ECU 4.463,2.489 5.095,2.650 0.633,0.161 10 HEAD LL 4.463,3.863 5.127,4.024 0.664,0.161 10 HEAD RL 2.634,2.649 2.903,2.816 0.268,0.168 10 A12 2.634,2.812 4.216,2.986 1.581,0.174 10 Headlight Bulb LH (Low) 2.634,3.954 2.903,4.122 0.268,0.168 10 A13 2.634,4.117 4.216,4.291 1.581,0.174 10 Headlight Bulb RH (Low) 3.112,3.633 3.217,3.801 0.105,0.168 10 1 3.549,3.633 3.652,3.793 0.103,0.160 10 2 3.112,2.258 3.217,2.425 0.105,0.168 10 1 3.549,2.258 3.652,2.418 0.103,0.160 10 2 5.855,1.034 6.277,1.175 0.422,0.140 10 HRLY

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test / Headlight Relay


e.

Check that the headlight (low) turn on/off.

Main Body ECU
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Headlight ON or OFF -

OK:

Headlight low beams turn on/off.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FUSE (HEAD LL, HEAD RL)
2.INSPECT FUSE (HEAD LL, HEAD RL)
a.
E161570E11
2.531,3.01 1.333,4.135 true 2.552,3.198 2.75,4.125 true 0.156,0.333 1.99,0.563 1.833,0.229 10 false Engine Room Relay Block: 0.74,4.125 1.344,4.448 0.604,0.323 10 false HEAD LL 2.333,4.146 3.031,4.542 0.698,0.396 10 false HEAD RL

Remove the HEAD LL and HEAD RL fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HEAD LL fuse Always Below 1 Ω
HEAD RL fuse Always Below 1 Ω



c.

Reinstall the HEAD LL and HEAD RL fuses.



OK

3.INSPECT HEADLIGHT (LOW) BULB

NG

REPLACE FUSE

3.INSPECT HEADLIGHT (LOW) BULB
a.

Temporarily replace the headlight (low) bulb with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY).


b.

Check that the headlight (low) turn on.

OK:

Headlight (low) turn on.




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LOW BULB - HEAD RELAY)
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LOW BULB - HEAD RELAY)
U153966E01
0.109,0.059 2.450,0.401 2.340,0.342 10 Front view of wire harness connector: (to Front Headlight Low Bulb) 0.224,2.139 0.505,2.295 0.281,0.157 10 A12 0.224,2.812 0.505,2.968 0.281,0.157 10 A13 0.712,2.149 0.892,2.320 0.181,0.171 10 *1 0.712,2.82 0.873,2.985 0.161,0.165 10 *2 2.803,2.614 3.228,2.775 0.424,0.161 10 *1: LH 2.803,2.969 3.250,3.131 0.447,0.162 10 *2: RH

a.

for LH:

i.

Disconnect the A12 headlight (low) LH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A12-2 - Body ground Light control switch HEAD, dimmer switch Low 11 to 14 V
Light control switch HEAD, dimmer switch except Low Below 1 V



iii.

Reinstall the headlight (low) LH connector.



b.

for RH:

i.

Disconnect the A13 headlight (low) RH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-2 - Body ground Light control switch HEAD, dimmer switch Low 11 to 14 V
Light control switch HEAD, dimmer switch except Low Below 1 V



iii.

Reinstall the headlight (low) RH connector.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT LOW BULB - BODY GROUND)

NG

5.INSPECT HEADLIGHT RELAY (HEAD)
5.INSPECT HEADLIGHT RELAY (HEAD)
A111813E28
2.448,0.74 2.792,0.365 false 2.813,1.052 3.135,1.052 false 2.063,1.083 1.813,1.083 false 2.49,1.438 2.49,1.792 false 2.854,0.208 3.01,0.375 0.156,0.167 10 false 1 0.406,1.219 0.563,1.385 0.156,0.167 10 false 1 1.688,1.021 1.844,1.188 0.156,0.167 10 false 3 0.406,0.813 0.563,0.979 0.156,0.167 10 false 3 2.448,1.792 2.604,1.958 0.156,0.167 10 false 2 1.313,1.219 1.469,1.385 0.156,0.167 10 false 2 3.208,0.969 3.365,1.135 0.156,0.167 10 false 5 1.313,0.813 1.469,0.979 0.156,0.167 10 false 5

a.

Remove the HEAD relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
When battery voltage is applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall the HEAD relay.



OK

6.CHECK HARNESS AND CONNECTOR (HEAD RELAY - BATTERY)

NG

REPLACE HEAD RELAY

6.CHECK HARNESS AND CONNECTOR (HEAD RELAY - BATTERY)
E147144E06
0.06,0.062 1.806,0.386 1.746,0.325 10 Component without relay: (Engine Room Relay Block) 0.432,3.006 1.260,3.160 0.828,0.154 10 HEAD Relay 1.153,2.001 0.222,3.089 0.222,3.089 0.391,3.089 false

a.

Remove the HEAD relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HEAD relay terminal 1 - Body ground Always 11 to 14 V
HEAD relay terminal 3 - Body ground Always 11 to 14 V



c.

Reinstall the HEAD relay.



OK

7.CHECK HARNESS AND CONNECTOR (HEAD RELAY - HEADLIGHT LOW BULB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEAD RELAY - HEADLIGHT LOW BULB)
a.

Remove the HEAD relay from the engine room relay block.

E344952E01
3.896,1.875 4.313,2.188 0.417,0.313 3.896,1.375 4.313,1.688 0.417,0.313 1.25,1.771 0.917,1.542 0.917,1.542 0.917,0.969 false 0.917,0.958 1.177,0.958 false 0.146,0.094 1.896,0.615 1.75,0.521 10 false Component without relay: (Engine Room Relay Block) 1.24,0.875 2.156,1.229 0.917,0.354 10 false HEAD Relay 4.365,0.094 6.667,0.583 2.302,0.49 10 false Front view of wire harness connector: (to Headlight (low) Bulb) 3.979,1.438 4.354,1.698 0.375,0.26 10 false A12 3.979,1.938 4.354,2.198 0.375,0.26 10 false A13 4.385,1.438 4.604,1.698 0.219,0.26 10 false *1 4.396,1.927 4.615,2.188 0.219,0.26 10 false *2 6.208,1.771 6.708,1.99 0.5,0.219 10 false *1: LH 6.219,2.021 6.719,2.24 0.5,0.219 10 false *2: RH


b.

for LH:

i.

Disconnect the A12 headlight (low) LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HEAD relay terminal 5 - A12-2 Always Below 1 Ω
HEAD relay terminal 5 - Body ground Always 10 kΩ or higher



iii.

Reinstall the headlight (low) LH connector.



c.

for RH:

i.

Disconnect the A13 headlight (low) RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HEAD relay terminal 5 - A13-2 Always Below 1 Ω
HEAD relay terminal 5 - Body ground Always 10 kΩ or higher



iii.

Reinstall the headlight (low) RH connector.



d.

Reinstall the HEAD relay.



OK

8.CHECK HEADLIGHT (HEADLIGHT RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HEADLIGHT (HEADLIGHT RELAY - MAIN BODY ECU)
U154006E01
0.06,0.049 2.445,0.399 2.385,0.350 10 Front view of wire harness connector: (to Main Body ECU) 1.615,1.355 1.841,1.511 0.225,0.156 10 DB 0.485,2.953 0.913,3.102 0.428,0.149 10 HRLY 0.727,2.919 1.015,2.395 false

a.

Disconnect the DB main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DB-18 - Body ground Always 11 to 14 V



c.

Reconnect the main body ECU connector.



OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR