Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE
RM27L0U _59 Vehicle Exterior _049355 EXTERIOR PANELS / TRIM _0236011 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


PROCEDURE

Hide 75445A 1.INSTALL NO. 5 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 5 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B211074E02
0.719,1.115 0.823,1.385 0.104,0.271 10 false a 1.323,1.125 1.427,1.396 0.104,0.271 10 false c 1.99,0.958 2.094,1.229 0.104,0.271 10 false b

Install a new No. 5 back door name plate as shown in the illustration.

Installation Position:
Mark Measurement (Along Surface)
a 54.2 mm (2.13 in.)
b 95.4 mm (3.76 in.)
c 53.9 mm (2.12 in.)


NOTICE:

Install the No. 5 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 5 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 5 back door name plate.



Hide 75443 2.INSTALL NO. 3 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 3 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B191718E04
1.281,1.469 1.406,1.635 0.125,0.167 10 false a 2.156,1.5 2.281,1.677 0.125,0.177 10 true b 2.896,1.406 3.01,1.573 0.115,0.167 10 true c

Install a new No. 3 back door name plate as shown in the illustration.

Installation Position:
Mark Measurement (Along Surface)
a 99.2 mm (3.91 in.)
b 104.5 mm (4.11 in.)
c 98.6 mm (3.88 in.)


NOTICE:

Install the No. 3 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 3 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 3 back door name plate.



Hide 75444A 3.INSTALL NO. 4 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 4 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B191719E03
0.563,1.365 0.708,1.563 0.146,0.198 10 false a 1.365,1.5 1.51,1.698 0.146,0.198 10 true b 2.073,1.49 2.198,1.708 0.125,0.219 10 true c

Install a new No. 4 back door name plate as shown in the illustration.

Installation Position:
Mark Measurement (Along Surface)
a 112.8 mm (4.44 in.)
b 87.8 mm (3.46 in.)
c 113.9 mm (4.48 in.)


NOTICE:

Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 3 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.



Hide 75741E 4.INSTALL SYMBOL EMBLEM

a.
B117713E02
0.259,3.499 0.837,3.832 0.578,0.333 10 Location Pin 1.105,3.521 0.93,3.608 false 2.418,3.738 2.996,4.071 0.578,0.333 10 Location Pin 2.37,3.814 2.105,3.665 false 2.726,1.832 3.259,2.177 0.533,0.345 10 Peeling Paper 2.701,1.918 2.515,1.732 false

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Insert the 2 pins into the back door panel and install the symbol emblem.

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.



Hide 75455E 5.INSTALL NO. 1 ROOF SIDE MARK

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B191720E03
1.688,1.167 1.344,1.792 false 1.948,3.385 2.51,4.052 false 0.052,2.323 0.677,2.479 0.625,0.156 10 false RH Side: 0.052,0.063 0.677,0.219 0.625,0.156 10 false LH Side: 0.802,1.354 0.906,1.521 0.104,0.167 10 false a 1.854,1.781 1.958,1.948 0.104,0.167 10 false b 2.656,1.313 2.781,1.479 0.125,0.167 10 false c 2.688,3.573 2.813,3.75 0.125,0.177 10 false d 1.677,4 1.802,4.167 0.125,0.167 10 false e 0.823,3.521 0.948,3.677 0.125,0.156 10 false f 0.292,1.75 1.427,1.938 1.135,0.188 10 false Relief R End Line 2.24,4.073 3.375,4.26 1.135,0.188 10 false Relief R End Line

Install a new No. 1 roof side mark as shown in the illustration.

Installation Position:
Mark Measurement (Along Surface)
a 4.6 mm (0.181 in.)
b 19.5 mm (0.768 in.)
c 4.6 mm (0.181 in.)
d 4.6 mm (0.181 in.)
e 16.3 mm (0.642 in.)
f 4.6 mm (0.181 in.)


NOTICE:

Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.



Hide 75455E 6.INSTALL NO. 1 ROOF SIDE MARK

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B191721E03
1.656,1.219 1.385,1.906 false 1.76,3.458 2.052,4.146 false 0.063,2.323 0.677,2.49 0.615,0.167 10 false RH Side: 0.063,0.042 0.688,0.208 0.625,0.167 10 false LH Side: 0.813,1.344 0.917,1.542 0.104,0.198 10 false a 1.802,1.833 1.917,2.01 0.115,0.177 10 false b 2.646,1.344 2.76,1.521 0.115,0.177 10 false c 2.677,3.625 2.792,3.802 0.115,0.177 10 false d 1.594,4.094 1.708,4.271 0.115,0.177 10 false e 0.865,3.625 0.948,3.823 0.083,0.198 10 false f 0.333,1.875 1.479,2.063 1.146,0.188 10 false Relief R End Line 2.115,4.094 3.26,4.281 1.146,0.188 10 false Relief R End Line

Install a new No. 1 roof side mark as shown in the illustration.

Installation Position:
Mark Measurement (Along Surface)
a 4.6 mm (0.181 in.)
b 26.6 mm (1.05 in.)
c 4.6 mm (0.181 in.)
d 4.6 mm (0.181 in.)
e 16 mm (0.630 in.)
f 4.6 mm (0.181 in.)


NOTICE:

Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.



Hide 75455E 7.INSTALL NO. 1 ROOF SIDE MARK

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel.

HINT:

Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



ii.

Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B209749E02
1.333,1.938 1.438,1.938 1.438,1.938 1.438,1.208 false 1.854,4.104 1.76,4.104 1.76,4.104 1.76,3.458 false 0.271,1.833 1.396,2.115 1.125,0.281 10 false Relief R End Line 1.896,4.021 3.021,4.302 1.125,0.281 10 false Relief R End Line 0.094,0.073 0.656,0.354 0.563,0.281 10 false LH Side: 0.115,2.563 0.698,2.844 0.583,0.281 10 false RH Side: 0.823,1.427 0.927,1.698 0.104,0.271 10 false a 0.823,3.5 0.927,3.771 0.104,0.271 10 false f 1.479,4.281 1.583,4.552 0.104,0.271 10 false e 2.677,3.646 2.781,3.917 0.104,0.271 10 false d 2.656,1.354 2.76,1.625 0.104,0.271 10 false c 1.792,2.063 1.896,2.333 0.104,0.271 10 false b

Install a new No. 1 roof side mark as shown in the illustration.

Installation Position:
Mark Measurement (Along Surface)
a 4.7 mm (0.185 in.)
b 33.6 mm (1.32 in.)
c 4.5 mm (0.177 in.)
d 4.4 mm (0.173 in.)
e 34.1 mm (1.34 in.)
f 4.5 mm (0.177 in.)


NOTICE:

Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.