Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.10
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P0430  Catalyst System Efficiency Below Threshold (Bank 2)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the Air-Fuel Ratio (A/F) sensor, sends pre-catalyst information to the ECM. The second sensor, the Heated Oxygen (HO2) sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the HO2 sensor while performing active air-fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.

The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and sets the DTC.

DTC Code DTC Detection Condition Trouble Area
P0420 OSC value smaller than standard value under active air-fuel ratio control
(2 trip detection logic)
·

Gas leakage from exhaust system

·

Air-Fuel Ratio (A/F) sensor (for Bank 1 Sensor 1)

·

Heated Oxygen (HO2) sensor (for Bank 1 Sensor 2)

·

Front No. 2 exhaust pipe assembly (TWC: Front Catalyst and Rear Catalyst)

·

Fuel pressure switching valve

·

Fuel pressure regulator

·

Fuel pressure regulator for high pressure


P0430 OSC value smaller than standard value under active air-fuel ratio control
(2 trip detection logic)
·

Gas leakage from exhaust system

·

Air-Fuel Ratio (A/F) sensor (for Bank 2 Sensor 1)

·

Heated Oxygen (HO2) sensor (for Bank 2 Sensor 2)

·

Front exhaust pipe assembly (TWC: Front Catalyst and Rear Catalyst)

·

Fuel pressure switching valve

·

Fuel pressure regulator

·

Fuel pressure regulator for high pressure



CATALYST LOCATION

A206067E03
0.276,0.177 2.536,0.488 2.260,0.311 10 Exhaust Manifold Sub-assembly RH 0.171,3.311 1.382,3.641 1.211,0.330 10 Exhaust Manifold Sub-assembly LH 5.864,0.939 7.091,1.240 1.228,0.301 10 Tailpipe Assembly 4.433,4.079 6.752,4.412 2.320,0.333 10 Front No. 2 Exhaust Pipe Assembly 1.679,2.038 2.733,2.341 1.054,0.303 10 Heated Oxygen Sensor 0.095,1.924 1.035,2.299 0.941,0.375 10 Air Fuel Ratio Sensor 5.717,2.374 7.067,2.683 1.350,0.309 10 Center Exhaust Pipe Assembly 2.593,0.416 4.908,0.805 2.315,0.389 10 Front Exhaust Pipe Assembly 2.627,4.333 4.033,4.496 1.406,0.163 10 TWC: Front Catalyst 0.61,2.601 2.016,2.764 1.406,0.163 10 TWC: Front Catalyst 3.122,0.877 4.528,1.040 1.406,0.163 10 TWC: Rear Catalyst 5.447,3.688 6.853,3.851 1.406,0.163 10 TWC: Rear Catalyst 1.485,3.881 2.854,4.023 1.369,0.142 10 Air Fuel Ratio Sensor 2.331,2.962 0.446,3.311 false 2.55,0.484 2.036,1.501 false 0.515,0.928 0.091,0.249 0.091,0.249 0.194,0.249 false 1.489,1.511 0.362,1.884 false 2.539,1.29 3.062,0.95 false 1.657,1.841 0.834,2.601 false 2.114,1.518 1.967,1.977 false 5.435,0.851 5.782,0.992 false 5.273,2.413 5.66,2.458 false 5.42,2.935 7.080,3.123 1.660,0.188 10 Heated Oxygen Sensor 4.144,3.374 5.184,3.005 5.184,3.005 5.331,3.005 false 4.694,3.49 5.359,3.768 false 4.239,3.525 4.519,4.048 false 3.88,3.705 2.858,4.287 false 3.296,3.151 1.661,3.852 false

NOTICE:
·

When DTC P0420 is output, replace the front No. 2 exhaust pipe assembly when catalyst replacement is necessary. (Excluding air fuel ratio sensor and heated oxygen sensor)

·

When DTC P0430 is output, replace the front exhaust pipe assembly when catalyst replacement is necessary. (Excluding air fuel ratio sensor and heated oxygen sensor)



MONITOR STRATEGY

Related DTCs P0420: Catalyst Deterioration (for Bank 1)
P0430: Catalyst Deterioration (for Bank 2)
Required Sensors/Components (Main) A/F sensor and HO2 sensor
Required Sensors/Components (Related) Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation Once per driving cycle
Duration About 30 seconds
MIL Operation 1 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil control valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058, P102D, P105D (Rear oxygen sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0136, P0137, P0138, P0139, P013A, P013C, P0156, P0157, P0158, P0159, P0607 (Rear oxygen sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0300 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2440 - P2447 (Secondary air injection system)
P0500 (Vehicle speed sensor)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
Battery voltage 11 V or more
Intake air temperature -10°C (14°F) or more
Engine coolant temperature 75°C (167°F) or more
Atmospheric pressure 76 kPa (570 mmHg) or more
Idling OFF
Engine speed Less than 3200 rpm
A/F sensor status Activated
Fuel system status Closed loop
Engine load 10 to 75%
All of following conditions (a), (b) and (c) met -
(a) Mass air flow rate 7.5 to 75 gm/sec
(b) Estimated front catalyst temperature 555 to 820°C (1031 to 1508°F)
(c) Estimated rear catalyst temperature 400 to 700°C (752 to 1292°F)
Shift position 4th or higher

TYPICAL MALFUNCTION THRESHOLDS

Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC) Less than 1

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

HINT:
·

It is necessary that the response of the heated oxygen sensor is normal in order to confirm DTC P0420 and P0430. Therefore, perform the driving pattern for the heated oxygen sensor monitor before performing the drive pattern for the catalyst efficiency monitor.

·

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.



A358822E02
1.26,4.667 1.49,4.229 1.49,4.229 1.635,4.229 false 0.083,0.063 3.083,0.281 3,0.219 10 false Heated Oxygen Sensor Monitor Driving Pattern 0.083,3.573 2.771,3.771 2.688,0.198 10 false Catalyst Efficiency Monitor Driving Pattern 0.302,0.594 1.26,0.802 0.958,0.208 10 false Vehicle Speed 0.104,1.125 1.302,1.323 1.198,0.198 10 false 60 km/h (37 mph) 0.083,4.938 1.24,5.135 1.156,0.198 10 false 60 km/h (37 mph) 0.813,2.052 1.208,2.271 0.396,0.219 10 false Idling 0.073,2.365 1.25,2.573 1.177,0.208 10 false Ignition Switch off 0.813,5.906 1.208,6.125 0.396,0.219 10 false Idling 0.052,6.208 1.229,6.417 1.177,0.208 10 false Ignition Switch off 1.844,1.99 2.073,2.198 0.229,0.208 10 false [A] 4.281,0.938 4.563,1.146 0.281,0.208 10 false [C] 5.271,0.938 5.552,1.146 0.281,0.208 10 false [C] 6.25,0.948 6.51,1.188 0.26,0.24 10 false [C] 4.781,3.104 5.052,3.313 0.271,0.208 10 false [D] 5.771,3.104 6.083,3.333 0.313,0.229 10 false [D] 6.74,3.094 7.031,3.302 0.292,0.208 10 false [D] 6.917,2.115 7.146,2.323 0.229,0.208 10 false [E] 1.375,5.948 1.604,6.156 0.229,0.208 10 false [E] 1.688,6.938 1.979,7.156 0.292,0.219 10 false [F] 3.563,6.938 3.792,7.146 0.229,0.208 10 false [I] 5.271,6.938 5.5,7.146 0.229,0.208 10 false [L] 6.833,6.948 7.063,7.156 0.229,0.208 10 false [N] 2.021,5.813 2.25,6.021 0.229,0.208 10 false [G] 3.833,5.813 4.063,6.021 0.229,0.208 10 false [J] 3.104,0.958 3.417,1.167 0.313,0.208 10 false [B]* 2.958,4.792 3.271,5 0.313,0.208 10 false [H]* 4.75,4.792 5.063,5 0.313,0.208 10 false [K]* 6.271,4.438 6.646,4.677 0.375,0.24 10 false [M]* 1.563,2.667 2.375,2.896 0.813,0.229 10 false Warming up 1.833,6.479 2.646,6.708 0.813,0.229 10 false Warming up 2.615,2.667 3.885,2.875 1.271,0.208 10 false 10 minutes or more 2.729,6.49 3.49,6.865 0.76,0.375 10 false 10 minutes or more 3.656,6.49 4.469,6.719 0.813,0.229 10 false Warming up 4.5,6.469 5.229,6.833 0.729,0.365 10 false 10 minutes or more 6.021,6.469 6.792,6.823 0.771,0.354 10 false 10 minutes or more 1.688,4.146 4.458,4.365 2.771,0.219 10 false Between 75 and 100 km/h (47 and 63 mph) 0.083,7.344 4.708,7.573 4.625,0.229 10 false *: Drive the vehicle while keeping the engine load as constant as possible.

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

8.

Check that Catalyst Efficiency / Current is Incomplete.

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

10.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


11.

With the shift lever in D, drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].

13.

Check the Test Value for RL F/C B1S2, RL F/C B2S2.

·

If Test Value displays a value larger than 0, perform the following procedure, as the O2 sensor monitor is finished.

·

If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.


14.

Turn the ignition switch off and wait for at least 30 seconds [F].

15.

Turn the ignition switch to ON and turn the Techstream on.

16.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].

17.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


18.

Turn the ignition switch off and wait for at least 30 seconds [I].

19.

Turn the ignition switch to ON and turn the Techstream on.

20.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [J].

21.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [K].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates [L].



22.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

23.

Check if any DTCs (pending DTCs) are stored.

HINT:

If the monitor item does not change to Complete, and no pending DTCs are stored, perform the following procedure.


24.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [M].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates [N].



25.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

26.

Check if any DTCs (pending DTCs) are stored.

HINT:

If the monitor item does not change to Complete, and no pending DTCs are stored, extend the driving time.


27.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the A/F and HO2 sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


A364135E12
4.865,3.083 4.865,3.313 4.865,3.313 5.281,3.313 false 5.188,3.313 5.188,3.083 false 0.542,0.667 1.51,0.854 0.969,0.188 10 false Engine Speed 0.844,1.01 1.49,1.208 0.646,0.198 10 false 3000 rpm 0.833,1.552 1.479,1.75 0.646,0.198 10 false 2000 rpm 1.094,2.531 1.49,2.74 0.396,0.208 10 false Idling 0.24,2.76 1.448,2.979 1.208,0.219 10 false Ignition Switch Off 2.063,2.396 2.302,2.604 0.24,0.208 10 false (b) 6.615,2.74 7.031,2.938 0.417,0.198 10 false Time 2.073,3.135 2.896,3.344 0.823,0.208 10 false Warming up 3.375,3.146 4.583,3.354 1.208,0.208 10 false At least 3 minutes 5.344,3.219 6.073,3.406 0.729,0.188 10 false 2 seconds 4.833,3.375 5.302,3.573 0.469,0.198 10 false Check 1.604,2.646 1.844,2.854 0.24,0.208 10 false (a) 3.594,0.896 3.833,1.073 0.24,0.177 10 false (c) 4.75,0.885 4.99,1.073 0.24,0.188 10 false (d) 5.052,1.438 5.292,1.625 0.24,0.188 10 false (d)

(a) Connect the Techstream to the DLC3.

(b) Start the engine and warm it up with all the accessories switched OFF until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm and 2000 rpm at 2 second intervals, check the waveforms of the A/F and HO2 sensors using the Techstream.


HINT:
·

If either voltage output of the Air-Fuel Ratio (A/F) or Heated Oxygen (HO2) sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the following Control the Injection Volume for A/F Sensor using the Techstream.

·

If the Three-Way Catalytic Converter (TWC) has deteriorated, the HO2 sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).



A121610E10
0.058,0.04 4.756,0.235 4.698,0.195 12 Voltage output when active air-fuel ratio control not performed: 2.374,0.421 3.663,0.601 1.289,0.180 10 Normal Catalyst 4.744,0.426 6.479,0.574 1.735,0.148 10 Deteriorated Catalyst 0.257,2.118 1.115,2.640 0.858,0.522 10 Waveform of HO2 Sensor behind TWC 0.257,0.653 1.269,1.297 1.012,0.644 10 Waveform of A/F Sensor in front of TWC 1.446,0.789 1.823,0.937 0.378,0.148 10 3.5 V 1.446,1.123 1.845,1.266 0.399,0.143 10 3.0 V 1.446,2.104 1.793,2.253 0.347,0.150 10 1.0 V 1.446,2.774 1.736,2.922 0.290,0.148 10 0 V 2.64,3.111 3.396,3.257 0.755,0.146 10 10 seconds 5.042,3.08 5.796,3.221 0.755,0.141 10 10 seconds

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.

1.

Connect the Techstream to the DLC3.

2.

Start the engine and turn the Techstream on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume.)

6.

Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.



HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+12.5% Rich Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5% Lean More than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+12.5% Rich More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5% Lean Less than 0.4 V

NOTICE:

The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


A283583E59
5.813,3.708 7.135,3.979 1.323,0.271 10 false - A/F sensor 3.635,4.927 4.521,5.104 0.885,0.177 8 false Less than 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.583,4.688 4.635,4.865 1.052,0.177 8 false More than 0.55 V 0.99,2.646 1.958,2.813 0.969,0.167 8 false More than 3.4 V 0.99,2.885 1.927,3.063 0.938,0.177 8 false Less than 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.573,2.604 4.656,2.792 1.083,0.188 8 false More than 0.55 V 3.625,2.844 4.5,3.021 0.875,0.177 8 false Less than 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.979,6.771 1.969,6.938 0.99,0.167 8 false More than 3.4 V 0.979,7.021 1.885,7.208 0.906,0.188 8 false Less than 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.542 0.49,0.771 0.375,0.229 10 false Case 0.677,0.542 3,0.76 2.323,0.219 10 false A/F Sensor (Sensor 1) Output Voltage 3.24,0.542 5.688,0.781 2.448,0.24 10 false HO2 Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.813,4.063 7.104,4.271 1.292,0.208 10 false - A/F sensor heater 5.813,4.448 7.073,4.646 1.26,0.198 10 false - A/F sensor circuit 5.802,5.813 6.854,6.188 1.052,0.375 10 false - HO2 sensor 5.792,6.198 7.104,6.406 1.313,0.208 10 false - HO2 sensor heater 5.802,6.604 7.104,6.802 1.302,0.198 10 false - HO2 sensor circuit 5.813,7.51 6.656,7.698 0.844,0.188 10 false - Injector 5.813,7.823 6.969,8.156 1.156,0.333 10 false - Fuel pressure 5.802,8.156 7.135,8.896 1.333,0.74 10 false - Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4,1.594 4.448,1.781 0.448,0.188 8 false +12.5% 4.01,3.667 4.458,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.385,5.75 1.833,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.01,7.781 4.458,7.969 0.448,0.188 8 false +12.5% 4.063,5.729 4.51,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 or P0174 (System Too Lean) and P0172 or P0175 (System Too Rich).

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P0420 or P0430 is output A
DTC P0420 or P0430 and other DTCs are output B

HINT:

If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leaks from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Lean/Rich Lean Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leaks from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leaks from exhaust system


C
Lean Lean Actual air fuel ratio lean
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system


D

Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.


h.

Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



A

3.CHECK FOR EXHAUST GAS LEAK

B

7.REPLACE AIR FUEL RATIO SENSOR

C

5.CHECK FOR EXHAUST GAS LEAK

D

6.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks from the exhaust manifold sub-assembly and exhaust pipes.

OK:

No gas leaks.




OK

4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NG

8.REPAIR OR REPLACE FOR EXHAUST GAS LEAK POINT
4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
NOTICE:
·

When DTC P0420 is output, replace the front No. 2 exhaust pipe assembly (TWC: Front catalyst and rear catalyst) when catalyst replacement is necessary.

·

When DTC P0430 is output, replace the front exhaust pipe assembly (TWC: Front catalyst and rear catalyst) when catalyst replacement is necessary.



HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC P0430 is output B
DTC P0420 and P0430 are output A and B



B

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

A

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks from the exhaust manifold assembly and exhaust pipes.

OK:

No gas leaks.




OK

9.REPLACE HEATED OXYGEN SENSOR

NG

8.REPAIR OR REPLACE FOR EXHAUST GAS LEAK POINT
6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks from the exhaust manifold assembly and exhaust pipes.

OK:

No gas leaks.




OK

10.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO

NG

8.REPAIR OR REPLACE FOR EXHAUST GAS LEAK POINT
7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE FOR EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>HEATED OXYGEN SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the Fuel Injection System Inspection Procedure (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>Fuel Injection System).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the Techstream on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0420 and/or P0430 is output A
DTC is not output B



A

12.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

B

END

12.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
NOTICE:
·

When DTC P0420 is output, replace the front No. 2 exhaust pipe assembly (TWC: Front catalyst and rear catalyst) when catalyst replacement is necessary.

·

When DTC P0430 is output, replace the front exhaust pipe assembly (TWC: Front catalyst and rear catalyst) when catalyst replacement is necessary.



HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC P0430 is output B
DTC P0420 and P0430 are output A and B



B

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

A

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)