Home › Engine / Hybrid System › 3UR-FBE FUEL › FUEL PUMP › from 2016.10
RM27L0U _51 Engine / Hybrid System _049297 3UR-FBE FUEL _0235571 FUEL PUMP A

3UR-FBE FUEL  FUEL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the fuel pump.

See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 23280 2.INSTALL FUEL PRESSURE REGULATOR ASSEMBLY

Hide 77020A 3.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the fuel pump.

Click hereEngine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of gasoline to a new gasket and install it to the fuel tank.


b.
A194658E04
2.354,0.531 2.417,0.156 2.417,0.156 2.531,0.156 false 2.354,1.479 2.76,1.479 false 2.802,1.385 3.031,1.583 0.229,0.198 10 true *b 2.563,0.083 2.854,0.271 0.292,0.188 10 true *a

Align the protrusion of the fuel suction with pump and gauge tube assembly with the groove of the fuel tank.

Text in Illustration
*a Protrusion
*b Groove


c.

Install the fuel suction with pump and gauge tube assembly into the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



d.
A387302C02
0.948,1.5 0.948,0.896 true 0.948,1.333 1.292,1.333 1.292,1.333 1.292,1.021 true 0.865,1.51 1.177,1.667 0.313,0.156 10 false *a
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the fuel suction with pump and gauge tube assembly.

HINT:

Perform this procedure when replacement of the fuel suction with pump and gauge tube assembly is necessary.



e.
A391908C01
2.531,0.771 2.823,0.521 2.823,0.521 3.031,0.521 false 1.667,0.885 1.875,0.885 1.875,0.885 2.323,0.823 true 3.031,0.417 3.344,0.573 0.313,0.156 10 false *a 1.5,0.771 1.813,0.927 0.313,0.156 10 false *b
*a Rotational Start Point Mark (Fuel Tank Assembly Side)
*b Rotational Start Point Mark (Fuel Pump Gauge Retainer Side)


Temporarily place the fuel pump gauge retainer by aligning the rotational start point mark of a new fuel pump gauge retainer with the rotational start point mark of the fuel tank assembly while pressing the fuel suction with pump and gauge tube into the fuel tank assembly.


f.
A390961C01
1.229,2.885 1.427,2.885 1.427,2.885 1.625,2.573 true 0.646,0.302 0.833,0.302 0.833,0.302 0.896,0.51 true 1.313,0.771 1.479,0.646 1.479,0.646 1.635,0.646 true 1.979,2.365 2.135,2.094 2.135,2.094 2.292,2.094 true 1,1.99 1.188,1.99 1.188,1.99 1.656,2.49 true 1.063,4.604 1.26,4.604 1.26,4.604 1.646,4.26 true 2.344,1.979 2.656,2.135 0.313,0.156 10 false *1 0.479,0.177 0.792,0.333 0.313,0.156 10 false *a 1.052,2.792 1.365,2.948 0.313,0.156 10 false *b 0.833,1.875 1.146,2.031 0.313,0.156 10 false *c 0.875,4.49 1.188,4.646 0.313,0.156 10 false *d 1.688,0.542 2,0.698 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (claw set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




g.
A390962C01
0.677,2.031 0.906,2.031 0.906,2.031 1.094,1.823 true 2.104,1.313 2.25,1.094 2.25,1.094 2.438,1.094 true 0.708,0.74 0.938,0.74 0.938,0.74 1.354,1.021 true 2.49,0.979 2.802,1.135 0.313,0.156 10 false *1 0.531,0.635 0.844,0.792 0.313,0.156 10 false *a 0.5,1.938 0.813,2.094 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.


h.
A390959C01
0.76,0.125 0.958,0.125 0.958,0.125 1.24,0.281 true 2.802,1.583 2.802,1.406 2.802,1.406 2.646,1.198 true 0.563,0.031 0.875,0.188 0.313,0.156 10 false *a 2.74,1.594 3.052,1.75 0.313,0.156 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).


i.
A387317C03
0.615,1.198 0.854,1.198 0.854,1.198 1.333,0.906 true 1.74,1.083 2.573,1.083 true 2.604,1 2.917,1.198 0.313,0.198 10 true *a 0.427,1.094 0.74,1.25 0.313,0.156 10 false *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


j.
A391923C01
0.917,0.677 1.115,0.677 1.115,0.677 1.313,0.99 false 0.656,2.542 1.052,2.542 false 1.927,0.802 2.208,0.583 2.208,0.583 2.427,0.583 false 1.781,1.146 1.99,1.594 1.99,1.594 2.25,1.594 true 0.771,2.125 0.969,2.125 0.969,2.125 1.375,2.385 false 0.75,0.583 1.063,0.74 0.313,0.156 10 false *1 0.479,2.448 0.813,2.604 0.333,0.156 10 false *a 2.458,0.479 2.771,0.635 0.313,0.156 10 false *b 0.583,2.021 0.896,2.177 0.313,0.156 10 false *c 2.281,1.5 2.594,1.656 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V100135

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


k.
A390960C02
0.792,0.823 0.792,0.354 true 0.438,0.354 1.271,0.354 1.271,0.354 1.271,0.948 true 0.281,0.198 0.594,0.354 0.313,0.156 10 false *a 0.479,1.365 0.667,1.604 0.188,0.24 10 true *c 2.813,0.604 3,0.844 0.188,0.24 10 true *b
*a Co-rotation Prevention Check Mark
*b Tightening Start Position
*c One and Half Rotation Position


While one person presses the fuel suction with pump and gauge tube assembly into the fuel tank assembly, have another person firmly press the fuel pump gauge retainer into the threads of the fuel tank assembly and tighten approximately one and a half turns.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel suction with pump and gauge tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.




l.

Check the tightening condition of the fuel pump gauge retainer.

i.
A390963C01
2.438,0.615 2.625,0.677 2.625,0.677 2.823,0.677 true 0.74,2.75 0.958,2.75 0.958,2.75 1.198,3.021 false 2.333,2.802 2.625,2.542 2.625,2.542 2.823,2.542 false 0.438,4.229 0.656,4.229 0.656,4.229 0.979,3.875 false 0.948,1.354 1.146,1.354 1.146,1.354 1.385,1.083 true 2.521,2.031 2.521,1.792 2.521,1.792 2.344,1.542 true 0.583,2.646 0.896,2.802 0.313,0.156 10 false *1 0.26,4.125 0.573,4.281 0.313,0.156 10 false *2 2.823,2.427 3.135,2.583 0.313,0.156 10 false *a 0.76,1.271 0.958,1.49 0.198,0.219 10 true *b 2.646,3.479 2.958,3.635 0.313,0.156 10 false *c 2.458,2.073 2.656,2.292 0.198,0.219 10 true *b 2.833,0.583 3.052,0.802 0.219,0.219 10 true *b
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a Vernier Caliper
*b Measurement Position
*c Measurement Height


Using a vernier caliper, measure the upper surface dimensions of the fuel tank assembly at the 3 positions as shown in the illustration.

Standard:

Measurement difference is within 3 mm.


NOTICE:

If the measurement difference is approximately 6 mm, the threads misaligned by 1 threads (6 mm) and the fuel pump gauge retainer must be installed again.




m.
A390964C01
0.708,1.333 0.927,1.333 0.927,1.333 1.104,1.219 true 0.5,1.229 0.813,1.385 0.313,0.156 10 false *a 2.479,1.625 2.792,1.781 0.313,0.156 10 false *b 3.052,0.458 3.365,0.615 0.313,0.156 10 false *c
*a SST (Plate)
*b Person in Charge of Tightening
*c Person in Charge of Supporting


While one person presses the fuel tank vent tube assembly into the fuel tank assembly, have another person slowly tighten approximately half turns.


n.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


o.
A390965C01
1.813,3.75 1.813,3.51 1.813,3.51 1.948,3.094 true 0.979,0.521 1.26,0.25 1.26,0.25 1.469,0.25 true 0.74,1.427 0.74,1.208 0.74,1.208 1.01,1.063 true 1.49,0.146 1.802,0.302 0.313,0.156 10 false *a 0.656,1.448 0.969,1.604 0.313,0.156 10 false *b 2.021,4.281 2.333,4.438 0.313,0.156 10 false *c 1.729,3.781 2.042,3.938 0.313,0.156 10 false *d 2.854,2.656 3.167,2.813 0.313,0.156 10 false *e 2.49,2 2.802,2.156 0.313,0.156 10 false *f 2.99,0.708 3.271,0.938 0.281,0.229 10 false *g
*a SST (Handle)
*b SST (Plate)
*c Tightening Complete Position
*d Rotational Start Point Mark of Fuel Pump Gauge Retainer
*e Rotational Start Point Mark of Fuel Tank Assembly
*f Person in Charge of Tightening
*g Person in Charge of Supporting
V100135

Tighten


While one person presses the fuel suction with pump and gauge tube assembly onto the fuel tank sub-assembly, have another person use SST (handle) and slowly tighten the fuel pump gauge retainer until it reaches the tightening complete position.


Hide 4.INSTALL FUEL PRESSURE SWITCHING VALVE ASSEMBLY

Hide 77100 5.INSTALL FUEL TANK ASSEMBLY

a.

Install the fuel tank assembly (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL TANK>INSTALLATION).