Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1424/24    Solar Sensor Circuit (Driver Side)

for Preparation Click here


DESCRIPTION

E107008E01
The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output voltage from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The A/C amplifier detects output voltage from the solar sensor.

DTC No.
DTC Detection Condition
Trouble Area
B1424/24
Open or short in driver side solar sensor circuit
  1. Solar sensor
  2. Harness or connector between solar sensor and A/C amplifier
  3. Harness or connector between solar sensor and body ECU
  4. A/C amplifier
  5. Body ECU

WIRING DIAGRAM


E109253E30


INSPECTION PROCEDURE

HINT:
  1. If DTC B1244 is output at the same time, troubleshoot DTC B1244 first (Click here).
  2. If the check is performed in a dark place, DTC B1421/21 or B1424/24 (solar sensor circuit abnormal) may be output even though the system is normal.

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Expose the sensing portion of the solar sensor to light.

    HINT:
    Use an incandescent light for inspection.

  1. Select the item below in the Data List, and read the display on Techstream.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (D Side)
    Driver side solar sensor / min.: 0, max.: 255
    Driver side solar sensor value increases as brightness increases
    -

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR)


    E124476E31
  1. Disconnect the solar sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-6 (CLTB) - A25-3 (CLTE)
    Ignition switch ON
    11 to 14 V
    A25-6 (CLTB) - A25-3 (CLTE)
    Ignition switch OFF
    Below 1 V



OK
Go to step 4
NG


3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - BODY ECU)


    C160415E06
  1. Disconnect the body ECU connector.



    E124476E31
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B6-6 (CLTB) - A25-6 (CLTB)
    Always
    Below 1 Ω
    B6-4 (CLTE) - A25-3 (CLTE)
    Always
    Below 1 Ω
    B6-6 (CLTB) - Body ground
    Always
    10 kΩ or higher
    B6-4 (CLTE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BODY ECU 

4.CHECK SOLAR SENSOR


    E109215E32
  1. Remove the solar sensor with its connector still connected.

  1. Connect the positive (+) lead from the battery to terminal 6 (CLTB), and the negative (-) lead to terminal 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-1 (TSL) - A25-3 (CLTE)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    A25-1 (TSL) - A25-3 (CLTE)
    Sensor is covered with a cloth
    Below 0.8 V

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
    2. As the inspection light is moved away from the sensor, the voltage increases.



NG
REPLACE SOLAR SENSOR
OK


5.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - A/C AMPLIFIER)


    E124476E33
  1. Disconnect the solar sensor connector.



    E143742E33
  1. Disconnect the A/C amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-31 (TSD) - A25-1 (TSL)
    Always
    Below 1 Ω
    A9-31 (TSD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER