ANTI-LOCK BRAKE SYSTEM > TEST MODE PROCEDURE |
| SPEED SENSOR SIGNAL CHECK (WHEN USING SST CHECK WIRE): |
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position (Automatic Transmission) or apply the parking brake (Manual Transmission).
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() |
Check that the ABS warning light is blinking in the Test Mode.
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here or Click here
|
Start the engine.
Using SST, perform the speed sensor signal check in Test Mode.
Drive the vehicle straight forward.
Accelerate the vehicle to a speed of 28 mph (45 km/h) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC |
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Read the number of blinks of the ABS warning light.

After performing the check, disconnect the SST from terminals TS and CG, TC and CG of the DLC3 and turn the ignition switch off.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Speed sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Speed sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Speed sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Speed sensor rotor |
| SPEED SENSOR SIGNAL CHECK (WHEN USING TECHSTREAM): |
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position.
Set Techstream to Test Mode (select "Signal Check").
![]() |
Check that the ABS warning light is blinking in the Test Mode.
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here or Click here
|
Start the engine.
Using Techstream, perform the speed sensor signal check in Test Mode.
Drive the vehicle straight forward.
Accelerate the vehicle to a speed of 28 mph (45 km/h) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC |
Read the DTC(s) by following the tester screen.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Speed sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Speed sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Speed sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Speed sensor rotor |