Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E07
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. High HC concentration levels can cause increase in exhaust emission levels. Extremely high concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the Crankshaft Position (CKP) sensor. The VVT sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Intake system
  15. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
When multiple DTCs for misfiring cylinders are set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 20 to 50 misfires per 1,000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and sets a DTC when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
  1. At a high engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.

  1. Misfire Monitor for Mexico Models
    The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
    1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.
    2. An excessive misfiring rate (approximately 500 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
    The ECM flashes the MIL and sets a DTC when the following condition, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
    1. A catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors / Components (Main)
Injector, Ignition coil, Spark plug
Required Sensors / Components (Related)
Crankshaft, Camshaft, Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 to 4000 crankshaft revolutions: Emission related misfire
200 to 600 crankshaft revolutions: Catalyst damaged misfire
MIL Operation
2 driving cycles: Emission related misfire
MIL flashes immediately: Catalyst damaged misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
The monitor will run whenever these DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0100, P0102, P0103 (MAF meter)
P0110, P0112, P0113 (IAT sensor)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (CKP sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0500 (Vehicle speed sensor)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
450 to 6500 rpm
Either of the following conditions is met
Condition (a) or (b)
(a) Engine start ECT
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel-cut
OFF

Monitor period of emission related misfire: 
First 1000 revolutions after engine start, or check mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damage-misfire (MIL blinks): 
All of the following conditions 1, 2 and 3 are met
Crankshaft 200 revolutions
1. Driving cycle
1st
2. Check mode
OFF
3. Engine RPM
Less than 2600 rpm
Except above (MIL blinks immediately)
Crankshaft 200 revolutions x 3
  1. FOR MEXICO MODELS:

Misfire: for Mexico models 
The monitor will run whenever these DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0100, P0102, P0103 (MAF meter)
P0110, P0112, P0113 (IAT sensor)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (CKP sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0500 (Vehicle speed sensor)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
450 to 4500 rpm
ECT
More than 65°C (149°F)
Fuel cut
OFF

Monitor period of emission-related-misfire: for Mexico models 
First 1000 revolutions after engine start, or check mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks): for Mexico models 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions
1. Driving cycles
1st
2. Check mode
OFF
Except above
Crankshaft 200 revolutions x 3

TYPICAL MALFUNCTION THRESHOLDS


Monitor period of emission-related-misfire: 
Misfire rate
1% or more

Monitor period of catalyst-damage-misfire (MIL blinks): 
Number of misfire per 200 revolutions
94 or more (varies with intake air amount and RPM)
Paired cylinders misfire (MIL blinks immediately)
Detected
  1. FOR MEXICO MODELS:

Monitor period of emission-related-misfire: for Mexico models 
Misfire rate
33.2 % or more: for 1st 1000 revolutions
16.6 % or more: after 1st 1000 revolutions

Monitor period of catalyst-damaged-misfire (MIL blinks): for Mexico models 
Number of misfire per 200 revolutions
94 or more (varies with intake air amount and RPM)
Paired cylinder misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM

Refer to DTC P0351 for wiring diagram of the ignition system .

A162495E02


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to the ON position.
  3. Turn the tester on.
  4. Record the DTC(s) and freeze frame data.
  5. Using the tester, switch the ECM from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (CYL #1 to #6) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Cylinder #1 Misfire Rate to Cylinder #6 Misfire Rate in the Data List.

    HINT:
    1. In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Cylinder #1 Misfire Rate to Cylinder #6 Misfire Rate in the Data List.

    Engine RPM
    Duration
    Idling
    3.5 minutes or more
    1000
    3 minutes or more
    2000
    1.5 minutes or more
    3000
    1 minute or more

  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the ignition switch OFF and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
    1. There was insufficient fuel volume in the tank.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
  5. After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Rate to Cylinder #6 Misfire Rate).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern after finishing repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine RPM. If misfires occur only in high engine RPM areas, only DTC P0300 is set.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the tester.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.
  8. When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be Rich (-20% or less) or Lean (+20% or more).
  9. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire have occurred only while warming up the engine.
  1. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs detection.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


3.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is correctly connected and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the tester.

    Result:
    Data List
    Tester Display
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM
  1. (a) Enter the following menus:
    1. Select: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Rate, #2, #3, #4, #5 and #6.
  2. (b) Read each value for CYL #1 to #6 displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:
    1. (1) Start the engine and let it idle.
    2. (2) Move the shift lever to the D position.
    3. (3) Check the CYL #1 to #6.
    4. (4) If misfire counts are still not displayed, perform steps (c) and (d).
  3. (c) Drive the vehicle with the MISFIRE RPM and MISFIRE LOAD noted in the "READ VALUE USING THE TECHSTREAM (MISFIRE RPM and MISFIRE LOAD )" procedures above.
  4. (d) Read the Cylinder #1 Misfire Rate to #6 or DTCs displayed on the tester.

    Result:

    Misfire Count
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 18
A


7.CHECK SPARK PLUG


    A126880E03
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Maximum gap:
    1.3 mm (0.0512 in.)

  1. Check the electrode for carbon deposits.
    Recommended spark plug: 
    Manufacturer
    Product
    DENSO
    FK20HR11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 29
OK


9.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR)


    A114616E08
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the E11 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard:
    Cylinder No. 1:
    Tester Connection
    Specified Condition
    I23-1 - Ground
    11 to 14 V
    I23-2 - Ground
    10 kΩ or higher
    I23-1 - #10 (E11-2)
    Below 1 Ω
    Cylinder No. 2:
    Tester Connection
    Specified Condition
    I24-1 - Ground
    11 to 14 V
    I24-2 - Ground
    10 kΩ or higher
    I24-1 - #20 (E11-3)
    Below 1 Ω
    Cylinder No. 3:
    Tester Connection
    Specified Condition
    I25-1 - Ground
    11 to 14 V
    I25-2 - Ground
    10 kΩ or higher
    I25-1 - #30 (E11-4)
    Below 1 Ω
    Cylinder No. 4:
    Tester Connection
    Specified Condition
    I26-1 - Ground
    11 to 14 V
    I26-2 - Ground
    10 kΩ or higher
    I26-1 - #40 (E11-5)
    Below 1 Ω
    Cylinder No. 5:
    Tester Connection
    Specified Condition
    I27-1 - Ground
    11 to 14 V
    I27-2 - Ground
    10 kΩ or higher
    I27-1 - #50 (E11-6)
    Below 1 Ω
    Cylinder No. 6:
    Tester Connection
    Specified Condition
    I28-1 - Ground
    11 to 14 V
    I28-2 - Ground
    10 kΩ or higher
    I28-1 - #60 (E11-7)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE)


    A162489E04
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    #10 (E11-2) - E01 (E9-7)
    9 to 14 V
    #20 (E11-3) - E01 (E9-7)
    9 to 14 V
    #30 (E11-4) - E01 (E9-7)
    9 to 14 V
    #40 (E11-5) - E01 (E9-7)
    9 to 14 V
    #50 (E11-6) - E01 (E9-7)
    9 to 14 V
    #60 (E11-7) - E01 (E9-7)
    9 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
OK


12.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage (Click here).

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


14.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)


    A135015E01
  1. Remove the cylinder head covers RH and LH.

  1. Turn the crankshaft to align the timing marks of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the timing marks of the camshaft pulley and camshaft bearing cap align.

  1. Turn the crankshaft clockwise by 360° if the timing marks do not align. Check if they align once again.

    OK:
    The timing marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING
OK


15.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


16.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 95°C (167°F and 203°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


17.READ VALUE USING TECHSTREAM (MASS AIR FLOW METER)

NOTICE:
  1. Perform the mass air flow (MAF) meter inspection by following the procedures below.
  2. Only replace the MAF meter when the MAF value in the DATA LIST (with the engine stopped) are not within the normal operating range or there is foreign matter on the MAF meter platinum hot wire (heater).

  1. Read the values using the Techstream (MAF).

NOTICE:
  1. Perform the inspection with the vehicle indoors and on a level surface.
  2. Perform the inspection of the MAF meter while it is installed to the air cleaner case (installed to the vehicle).
  3. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Wait 30 seconds, and read the values on the Techstream.

    Standard condition:
    Less than 0.70 g/s

    1. If the result is not as specified, replace the MAF meter.
    1. If the result is within the specified range, inspect the cause of the extremely rich or lean air fuel ratio.



NG
REPLACE MASS AIR FLOW METER
OK

REPLACE ECM 

18.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage (Click here).

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


19.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)


    A135015E01
  1. Remove the cylinder head covers RH and LH.

  1. Turn the crankshaft to align the timing marks of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the timing marks of the camshaft pulley and camshaft bearing cap align.

  1. Turn the crankshaft clockwise by 360° if the timing marks do not align. Check if they align once again.

    OK:
    The timing marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING
OK


20.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


21.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 95°C (167°F and 203°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


22.READ VALUE USING TECHSTREAM (MASS AIR FLOW METER)

NOTICE:
  1. Perform the mass air flow (MAF) meter inspection by following the procedures below.
  2. Only replace the MAF meter when the MAF value in the DATA LIST (with the engine stopped) are not within the normal operating range or there is foreign matter on the MAF meter platinum hot wire (heater).

  1. Read the values using the Techstream (MAF).

NOTICE:
  1. Perform the inspection with the vehicle indoors and on a level surface.
  2. Perform the inspection of the MAF meter while it is installed to the air cleaner case (installed to the vehicle).
  3. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Wait 30 seconds, and read the values on the Techstream.

    Standard condition:
    Less than 0.70 g/s

    1. If the result is not as specified, replace the MAF meter.
    1. If the result is within the specified range, inspect the cause of the extremely rich or lean air fuel ratio.



NG
REPLACE MASS AIR FLOW METER
OK


23.CHECK SPARK PLUG


    A126880E03
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Maximum gap:
    1.3 mm (0.0512 in.)

  1. Check the electrode for carbon deposits.
    Recommended spark plug: 
    Manufacturer
    Product
    DENSO
    FK20HR11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG
OK


24.CHECK FOR SPARKS AND IGNITION (SPARK TEST)


    A136826
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 29
OK


25.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


26.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR)


    A114616E08
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the E11 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard:
    Cylinder No. 1:
    Tester Connection
    Specified Condition
    I23-1 - Ground
    11 to 14 V
    I23-2 - Ground
    10 kΩ or higher
    I23-1 - #10 (E11-2)
    Below 1 Ω
    Cylinder No. 2:
    Tester Connection
    Specified Condition
    I24-1 - Ground
    11 to 14 V
    I24-2 - Ground
    10 kΩ or higher
    I24-1 - #20 (E11-3)
    Below 1 Ω
    Cylinder No. 3:
    Tester Connection
    Specified Condition
    I25-1 - Ground
    11 to 14 V
    I25-2 - Ground
    10 kΩ or higher
    I25-1 - #30 (E11-4)
    Below 1 Ω
    Cylinder No. 4:
    Tester Connection
    Specified Condition
    I26-1 - Ground
    11 to 14 V
    I26-2 - Ground
    10 kΩ or higher
    I26-1 - #40 (E11-5)
    Below 1 Ω
    Cylinder No. 5:
    Tester Connection
    Specified Condition
    I27-1 - Ground
    11 to 14 V
    I27-2 - Ground
    10 kΩ or higher
    I27-1 - #50 (E11-6)
    Below 1 Ω
    Cylinder No. 6:
    Tester Connection
    Specified Condition
    I28-1 - Ground
    11 to 14 V
    I28-2 - Ground
    10 kΩ or higher
    I28-1 - #60 (E11-7)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


27.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE)


    A162489E04
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    #10 (E11-2) - E01 (E9-7)
    9 to 14 V
    #20 (E11-3) - E01 (E9-7)
    9 to 14 V
    #30 (E11-4) - E01 (E9-7)
    9 to 14 V
    #40 (E11-5) - E01 (E9-7)
    9 to 14 V
    #50 (E11-6) - E01 (E9-7)
    9 to 14 V
    #60 (E11-7) - E01 (E9-7)
    9 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
OK


28.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE ECM 

29.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 30
OK

REPLACE SPARK PLUG  

30.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER


NG
REPLACE ECM
OK

REPLACE IGNITION COIL