Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > TEST MODE PROCEDURE

for Preparation Click here



TEST MODE PROCEDURE

HINT:
  1. Operation of the tire pressure warning reset switch can be checked in TEST MODE.
  2. During TEST MODE, the system is not initialized by pushing the tire pressure warning reset switch. The circuit of the tire pressure warning reset switch can be inspected during this mode.

  1. Turn the ignition switch OFF.

  2. Connect Techstream to the DLC3.

  3. Turn the ignition switch ON.

  4. Check that the tire pressure warning light turns on for 3 seconds and then goes off.

  5. Turn the tester ON.

  6. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.



  7. F100632E06
  8. Confirm that the tire pressure warning light in the combination meter blinks at 0.125 seconds intervals.


PERFORM SIGNAL CHECK

HINT:
  1. When entering signal check mode, the tire pressure warning ECU sets all the signal check DTCs first.
    After completing the signal check for each inspection item, the DTCs for systems that are determined to be normal by the tire pressure warning ECU will be erased.
    The DTCs for other inspection items may not be erased when only a certain signal is inspected.
  2. When signal check returns to normal mode, all the signal check DTCs will be erased.

  1. Turn the ignition switch OFF.

  2. Connect Techstream to the DLC3.

  3. Turn the ignition switch ON and the tester ON.

  4. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

    HINT:
    Every time the test mode DTC erasure conditions are satisfied, the tire pressure warning light turns on for 1 second. Then, the tire pressure warning light blinks at 0.125 seconds intervals.

  5. Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

  6. Check that the tire pressure warning system test mode DTCs are erased.

    Test Mode DTC
    Test Signal
    Test Mode DTC Clear Condition
    C2181/81 to C2184/84
    Transmitter Data
    Receive data from the transmitter which has a registered ID in the tire pressure warning ECU
    C2191/91
    Vehicle Speed Signal
    Vehicle speed of 20 km/h (12 mph) or more is detected for 3 seconds or more

  7. Check the tire pressure warning reset switch.

    1. Press the tire pressure warning reset switch.

    2. Check the tire pressure warning light.

      Test Signal
      Normal Condition
      Tire Pressure Warning Reset Switch
      1. Switch ON: Tire pressure warning light turns on.
      2. Switch OFF: Tire pressure warning light blinks at 0.125 seconds intervals.

  8. Result

    HINT:
    After the signal check is completed, check for a signal check DTC to confirm the system status.


    Condition
    Procedure
    Test mode DTC is output
    Repair the faulty part and enter SIGNAL CHECK again
    Test mode DTCs are cleared
    No problem

  9. End of SIGNAL CHECK

    1. After completing the test mode (SIGNAL CHECK), turn the ignition switch OFF and disconnect the tester.

  10. DTC of SIGNAL CHECK (TEST DIAGNOSIS)

    1. If a trouble code is displayed during the test mode DTC check, check the circuit listed for that code. For details of each code, refer to the "See page" below.

      DTC Code
      Detection Item
      Trouble Area
      See page
      C2181/81
      Transmitter ID1 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Wire harness or connector
      4. Tire pressure warning ECU
      Click here
      C2182/82
      Transmitter ID2 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Wire harness or connector
      4. Tire pressure warning ECU
      Click here
      C2183/83
      Transmitter ID3 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Wire harness or connector
      4. Tire pressure warning ECU
      Click here
      C2184/84
      Transmitter ID4 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Wire harness or connector
      4. Tire pressure warning ECU
      Click here
      C2191/91
      Vehicle speed signal error
      1. Combination meter
      2. Wire harness or connector
      3. Vehicle speed signal circuit
      4. Tire pressure warning ECU
      Click here