Home › ENGINE › 2GR-FE COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A128115E03
  1. Install a new water pump gasket and the water pump assembly with the 16 bolts.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Bolt B and C:
    11 N*m{ 112 kgf*cm , 8 in.*lbf }

    NOTICE:
    1. Make sure that there is no oil on the threads of bolts A.
    2. Be sure to replace 2 bolts C with new ones or reuse them after applying adhesive 1344.

      Adhesive:
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



2. INSTALL WATER INLET HOUSING


    A128122
  1. Install a new water inlet housing gasket and water outlet pipe O-ring.



    A133375E04
  1. Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful not to allow the O-ring to get caught between the parts.

  1. Connect the water hose.



3. INSTALL WATER PUMP PULLEY


    A128112E01
  1. Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



4. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A161449
  1. Install the V-ribbed belt tensioner assembly with the 5 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A195781E01
  1. Install the 2 idler pulley cover plates, 2 No. 2 idler pulley cover plates and 2 No. 2 idler pulley sub-assemblies with the 2 bolts.

    Torque:
    54 N*m{ 550 kgf*cm , 40 ft.*lbf }

    HINT:
    Plate diameter:
    Idler pulley cover plate: 33.6 mm (1.32 in.)
    No. 2 idler pulley cover plate: 37.8 mm (1.49 in.)



6. INSTALL NO. 1 ENGINE FRONT MOUNTING BRACKET LH


    A129646
  1. Install the No. 1 engine front mounting bracket LH with the 6 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



7. INSTALL GENERATOR ASSEMBLY


    A135391
  1. Install the bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A128066
  1. Install the wire harness clamp stay.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    A162683E01
  1. Connect the wire harness clamp.

  1. Install the generator assembly to the cylinder block with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A133866
  1. Install the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A133865
  1. Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 2 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.



8. INSTALL COMPRESSOR AND MAGNETIC CLUTCH


    E146649E01
  1. Using a "TORX" socket wrench (E8), install the compressor and magnetic clutch with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

    HINT:
    Tighten the stud bolts in the order shown in the illustration.



    E146650E01
  1. Install the compressor and magnetic clutch with the 2 bolts and the 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts and nuts in the order shown in the illustration.

  1. Connect the 2 clamps and wire harness.

  1. Connect the connector.



9. INSTALL ENGINE HANGERS


    A129635E12
  1. Install the 4 bolts, and 2 engine hangers.



10. REMOVE ENGINE STAND


11. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Click here



12. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Remove the air drain cock plug from the water inlet housing.



    A162799E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    11.3 liters (12.0 US qts, 10.0 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



13. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.



    A161453
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.