Home › ENGINE › 2GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR


    A129648
  1. Using a 19 mm deep socket wrench, install the engine coolant temperature sensor and a new gasket.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }



2. INSTALL KNOCK CONTROL SENSOR


    A132951E01
  1. Install the 2 knock control sensors with the 2 bolts as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 knock control sensor connectors.



3. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    P012478E01
  1. Clean the threads of the oil pressure switch. Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent



    A139194
  1. Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation to prevent oil leaks.



4. INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY


    A132992
  1. Install the bolt and No. 1 vacuum switching valve.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. INSTALL RADIO SETTING CONDENSER


    A132991
  1. Install the 2 bolts and 2 radio setting condensers.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL NO. 1 ENGINE FRONT MOUNTING BRACKET LH


    A129646
  1. Install the No. 1 engine front mounting bracket LH with the 6 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



7. INSTALL WATER PUMP PULLEY


    A128112E01
  1. Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



8. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A186537E02
  1. Install the No. 2 idler pulley sub-assembly and 2 plates with the bolt.

    Torque:
    54 N*m{ 550 kgf*cm , 40 ft.*lbf }

    HINT:
    Plate diameter:
    Idler pulley cover plate: 33.6 mm (1.32 in.)
    No. 2 idler pulley cover plate: 37.8 mm (1.49 in.)



9. INSTALL NO. 2 TIMING GEAR COVER


    A132987
  1. Install the No. 2 timing gear cover with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



10. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A129644E01
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

    HINT:
    Each bolt length is as follows:
    A: 70 mm (2.76 in.)
    B: 33 mm (1.30 in.)

  1. Install the V-ribbed belt tensioner by tightening the bolt 1 and bolt 2 in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



11. INSTALL GENERATOR ASSEMBLY


    A135391
  1. Install the bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A128066
  1. Install the wire harness clamp stay.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    A162683E01
  1. Connect the wire harness clamp.

  1. Install the generator assembly to the cylinder block with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A133866
  1. Install the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A133865
  1. Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 2 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.



12. INSTALL COOLER COMPRESSOR ASSEMBLY


    E146649E01
  1. Using a "TORX" socket wrench (E8), install the compressor and magnetic clutch with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

    HINT:
    Tighten the stud bolts in the order shown in the illustration.



    E146650E01
  1. Install the compressor and magnetic clutch with the 2 bolts and the 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts and nuts in the order shown in the illustration.

  1. Connect the 2 clamps and wire harness.

  1. Connect the connector.



13. INSTALL ENGINE MOUNTING BRACKET RR (for 4WD)


    A143881
  1. Install the engine mounting bracket RR with the 3 bolts.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



14. INSTALL DRIVE SHAFT BEARING BRACKET (for 2WD)


    A163583
  1. Install the drive shaft bearing bracket with the 3 bolts.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



15. INSTALL ENGINE MOUNTING BRACKET RH


    A129642
  1. Install the engine mounting bracket RH with the 3 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



16. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A129649E01
  1. Install a new gasket as shown in the illustration.



    A129641E01
  1. Install the exhaust manifold sub-assembly LH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



17. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A140784
  1. Install the No. 2 insulator with the 3 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



18. INSTALL NO. 2 MANIFOLD STAY


    A140783E01
  1. Install the No. 2 manifold stay with the bolt and nut in the order shown in the illustration.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



19. INSTALL OIL LEVEL GAUGE GUIDE SUB-ASSEMBLY


    A155017
  1. Install 2 new O-rings to the oil level gauge guide.

  1. Apply a light coat of engine oil to the O-rings.

  1. Push in the oil level gauge guide end into the guide hole.

  1. Install the No. 1 oil level gauge guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the No. 2 oil level gauge guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the oil level gauge.



20. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A129650E01
  1. Install a new gasket as shown in the illustration.



    A140781E01
  1. Install the exhaust manifold sub-assembly RH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



21. INSTALL INTAKE MANIFOLD

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Intake Manifold and Cylinder Head Sub-assembly RH
Intake Manifold and Cylinder Head Sub-assembly LH



    A134933
  1. Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Make sure that the gasket is installed in the correct direction.

  1. Set the intake manifold on the cylinder heads.

  1. Install and tighten the 6 bolts and 4 nuts uniformly in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



22. INSTALL NO. 2 ENGINE MOUNTING STAY RH


    A162388
  1. Install the No. 2 mounting stay RH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



23. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 6 ignition coil assemblies with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



24. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Surge Tank and Intake Manifold
No. 1 Surge Tank Stay and Cylinder Head Cover
No. 1 Surge Tank Stay and Surge Tank
Throttle Body Bracket and Cylinder Head Cover
Throttle Body Bracket and Surge Tank

  1. Install a new gasket to the intake air surge tank.



    A139209
  1. Using a 5 mm hexagon socket wrench, install the 4 bolts and 2 nuts.

    Torque:
    Bolt:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Install the throttle body bracket, No. 1 surge tank stay and 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A129467
  1. Connect the connector.

  1. Connect the No. 1 ventilation hose.



    A129464E04
  1. Install the clamp and connect the throttle with motor body assembly connector.

  1. Connect the vapor feed hose.

  1. Connect the 2 water by-pass hoses to the throttle with motor body assembly.



25. INSTALL VENTILATION HOSE


    A162372
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to the intake air surge tank assembly and ventilation valve.



26. INSTALL ENGINE HANGERS


    A129635E12
  1. Install the 4 bolts, and 2 engine hangers.



27. REMOVE ENGINE STAND


28. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A129631E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011   (09213-70020)
    09330-00021  



    P000601E04
  1. Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent




      A132243E01
    1. Install the front spacer, drive plate and rear spacer on the crankshaft.

    2. Install and tighten the 8 mounting bolts uniformly in several steps.

      Torque:
      83 N*m{ 850 kgf*cm , 61 ft.*lbf }



29. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD)

HINT:
Click here.



30. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for 4WD)

HINT:
.



31. INSTALL TRANSFER STIFFENER PLATE RH


    D030512
  1. Install the transfer stiffener plate RH with 5 bolts to the transfer and engine mounting bracket RR.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



32. INSTALL MANIFOLD STAY


    A155023
  1. Install the bolt, nut, and manifold stay.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



33. INSTALL ENGINE FRONT MOUNTING BRACKET


    D030470
  1. Install the engine mounting bracket front to the automatic transaxle with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



34. INSTALL STARTER ASSEMBLY


    A160252
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 380 kgf*cm , 26 ft.*lbf } for bolt



    A160251
  1. Connect the starter connector.

  1. Install the terminal nut and cover the nut with the cap.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf } for nut



35. INSTALL ENGINE WIRE


36. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the inboard joint shaft assembly with ATF.



    C083851
  1. Align the shaft splines and install the drive shaft assembly with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing down.
    2. Be careful not to damage the drive shaft dust cover, boot and oil seal.
    3. Move the drive shaft assembly while keeping it level.



37. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)


    C080304
  1. Using a screwdriver, install a new bearing bracket hole snap ring.

    NOTICE:
    Do not damage the oil seal and boot.

  1. Install the bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



38. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Install the RH side using the same procedures as for the LH side.

NOTICE:
  1. Set the snap ring with the opening side facing downward.
  2. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.



39. INSTALL FRONT FRAME ASSEMBLY


    A163266E01
  1. Install the engine mounting insulators RH and LH with the 2 nuts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



    A155019
  1. Install the engine mounting insulator FR with the bolt.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }



    A155018
  1. Install the engine mounting insulator RR with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }



    A155022
  1. Connect the connector and clamp.



40. INSTALL POWER STEERING LINK


    D029979
  1. Install the power steering gear assembly with the 2 bolts and nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



41. INSTALL FRONT STABILIZER BAR

HINT:
(Click here).



42. REMOVE ENGINE HANGERS


    A129635E12
  1. Remove the 4 bolts and 2 engine hangers.



43. INSTALL VANE PUMP ASSEMBLY


    A139216
  1. Install the vane pump with the 2 bolts and nut.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A155024
  1. Install the 2 pressure feed tube clamp nuts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the power steering oil pressure switch connector.



44. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine assembly with transaxle on the engine lifter.

  1. Install the engine assembly to the vehicle.



    A162364
  1. Install the frame side rail plates RH and LH with the 6 bolts and 2 nuts.

    Torque:
    A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    B:
    32 N*m{ 329 kgf*cm , 24 ft.*lbf }



    A162363
  1. Install the front suspension member brace rear RH and LH with the 6 bolts and 2 nuts.

    Torque:
    A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    B:
    32 N*m{ 329 kgf*cm , 24 ft.*lbf }



45. RECONNECT SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring onto the suction hose sub-assembly.



    E145265
  1. Install the suction hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



46. RECONNECT DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring onto the discharge hose sub-assembly.



    E145264
  1. Install the discharge hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



47. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    D029986E02
  1. Align the matchmarks on the intermediate shaft assembly and steering gear assembly.

  1. Install the steering intermediate shaft assembly with the bolt.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }



    D030704E02
  1. Install the dust cover to the hole cover. Check that the 3 clips of the dust cover are securely fitted into the groove on the hole cover.



48. INSTALL FRONT AXLE ASSEMBLY LH


    F047689E06
  1. Install the drive shaft assembly LH to the front axle assembly LH.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.



49. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



50. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM LH


    F040142
  1. Install the lower ball joint to the front suspension arm sub-assembly lower with the bolt and nuts.

    Torque:
    127 N*m{ 1,300 kgf*cm , 94 ft.*lbf }



51. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.



52. INSTALL TIE ROD ASSEMBLY LH
  1. Install the tie rod end to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut up to 60° further.



53. INSTALL TIE ROD ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



54. INSTALL FRONT SPEED SENSOR LH


    F040147
  1. Install the speed sensor to the steering knuckle with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Prevent foreign matter from adhering to the speed sensor.



    C083022
  1. Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the clip of sensor on knuckle.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.



55. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



56. INSTALL FRONT AXLE HUB NUT LH
  1. Clean the threaded parts on the drive shaft and front axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C068609
  1. Using a socket wrench (30 mm), install a new axle hub LH nut.

    Torque:
    294 N*m{ 3,000 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the axle hub LH nut.



57. INSTALL FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.



58. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    F040136
  1. Install the stabilizer link assembly LH with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with nut. use a hexagon (6 mm) wrench to hold the stud.



59. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



60. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    C092265E01
  1. Align the matchmarks on the propeller shaft assembly rear flange and differential companion flange, and connect the shaft with the 4 bolts, washers and nuts.



    G024034E01
  1. Remove SST(s) from the extension housing.

  1. Insert the yoke into the extension housing.

    NOTICE:
    1. Be careful not to damage the oil seal.
    2. Be careful not to damage the universal joint boot when installing the propeller shaft.



    C083005
  1. Install the 2 adjusting shims and propeller shaft w/ center bearing, and loosely tighten the 4 bolts.



    C092265
  1. Tighten the 4 nuts.

    Torque:
    74 N*m{ 750 kgf*cm , 54 ft.*lbf }



61. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    F040503E01
  1. Remove the cloth from the joint.

  1. Using a hexagon wrench (6 mm), tighten the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F040527E03
  1. With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft, as shown in the illustration.



    F040528E01
  1. Adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion to 12.5 +- 1.0 mm (0.492 +- 0.039 in.) respectively as shown in the illustration, then torque the bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Check that the center line of the bracket is at right angles to the shaft axial direction.



  1. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.

    1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

    2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

    3. Remove the transfer dynamic damper.

    4. Using SST(s), measure the installation angle of the transfer extension housing (A) and front propeller shaft (B).

      SST
      09370-50010  

      No. 1 joint angle:
      A minus B = -0.4° to -1.6°



    5. Using SST(s), measure the installation angle of the rear propeller shaft (C) and rear differential (D).

      SST
      09370-50010  

      No. 2 joint angle:
      C minus D = -1.6° to -3.6°



      F040924E03

      If the measured angle is not within the specification, adjust with the center support bearing adjusting shim.

      Center support bearing adjusting shim thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      3.2 (0.126)
      4.5 (0.177)
      6.5 (0.256)
      9.0 (0.354)

  1. Install the transfer dynamic damper.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



62. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2WD)
  1. Install the front exhaust pipe assembly .



63. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 4WD)
  1. Install front exhaust pipe assembly .



64. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install center exhaust pipe assembly .



65. CONNECT ENGINE WIRE


    A163267
  1. Install the 2 bolts and 2 ground cables.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



    A155030
  1. Install the bolt and 2 clamps to the body.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



    A155037
  1. Connect the wire to the engine room junction block. Then, install it with the nut.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the engine wire to the body with the 2 nuts.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



66. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE


    A155029
  1. Using pliers, grip the claws of the clip and slide the clip to connect the No. 1 oil reservoir to pump hose to the oil reservoir tank.



67. CONNECT RETURN TUBE SUB-ASSEMBLY


    A052327
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to connect 2 return tube sub-assemblies.

    NOTICE:
    Take care not to damage the hose protector.



68. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C090579
  1. Connect the control cable to the control cable clamp.



    D025414E04
  1. Install the transmission control cable assembly to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C089134E02
  1. Connect the transmission control cable assembly to the bracket with a new clip.



69. CONNECT FUEL TUBE SUB-ASSEMBLY


    B012944
  1. Push in the fuel tube connector to the fuel pipe until the fuel tube makes a "click" sound.

    NOTICE:
    1. Check for damage or contamination on the connected part of the pipe.
    2. Check if the pipe and the connector are securely connected by trying to pull them apart.



    A155045
  1. Install the No. 1 fuel pipe clamp.



70. CONNECT NO. 1 OIL COOLER OUTLET HOSE


    A155031
  1. Using pliers, grip the claws of the clip and slide the clip to connect the No. 1 oil cooler outlet hose to the No. 1 oil cooler outlet tube.



71. CONNECT NO. 1 OIL COOLER INLET HOSE


    A155032
  1. Using pliers, grip the claws of the clip and slide the clip to connect the No. 1 oil cooler inlet hose to the No. 1 oil cooler inlet tube.



72. CONNECT HEATER WATER INLET HOSE B


    A155043
  1. Using pliers, grip the claws of the clip and slide the clip to connect the heater water inlet hose to water outlet.



73. CONNECT HEATER WATER OUTLET HOSE B


    A155044
  1. Using pliers, grip the claws of the clip and slide the clip to connect the heater water outlet hose to water outlet.



74. INSTALL RADIATOR INLET HOSE


    A155046
  1. Using pliers, grip the claws of the clip and slide the clip to connect the radiator inlet hose to the water outlet.



75. INSTALL RADIATOR OUTLET HOSE


    A155038
  1. Using pliers, grip the claws of the clip and slide the clip to connect the radiator outlet hose to the water inlet.



76. CONNECT UNION TO CHECK VALVE HOSE


    A162374
  1. Using pliers, grip the claws of the clip and slide the clip to connect the union to check valve hose to the intake air surge tank assembly.



77. CONNECT NO. 1 FUEL VAPOR FEED HOSE


    A155036
  1. Install the clamp and connect the No. 1 fuel vapor feed hose.



78. INSTALL ENGINE MOVING CONTROL ROD


    A162369
  1. Temporarily install the engine moving control rod with the 3 bolts.

  1. First install the bolts A, and then the remaining bolt B.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }



79. INSTALL NO. 2 ENGINE MOUNTING STAY RH


    A139217
  1. Temporarily install the No. 2 engine mounting stay RH with the bolt.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }

  1. Tighten the 2 nuts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



80. INSTALL INTAKE AIR RESONATOR SUB-ASSEMBLY


    A155042
  1. Install the intake air resonator with the bolt and clip.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



81. INSTALL AIR CLEANER BRACKET


    A155041
  1. Remove the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



82. INSTALL BATTERY


    A155033
  1. Install the battery and battery tray.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Nut:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the positive battery terminal.

  1. Connect the negative battery terminal.



83. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A155039
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose.

  1. Connect the vacuum switching valve connector.



84. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Install the air cleaner filter element sub-assembly.



85. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A161845
  1. Install the air cleaner filter element, and air cleaner cap sub-assembly with the 2 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }



    A162723E01
  1. Connect the 3 vacuum hoses.



    A162726
  1. Tighten the bolt, connect the 2 connectors, and install the 2 vacuum hoses.



86. INSTALL NO. 1 AIR CLEANER INLET


    A155040
  1. Install the No. 1 air cleaner inlet with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



87. INSTALL NO. 2 AIR CLEANER INLET


    A133004
  1. Install the No. 2 air cleaner inlet with the 2 clamps and 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



88. CONNECT VACUUM HOSES



A133002E01



89. INSTALL V-RIBBED BELT


    A162386E01
  1. Install the V-ribbed belt.

  1. Using SST, turn the belt tensioner counterclockwise and remove the bar.

    SST
    09249-63010  



    A129623E02
  1. If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the tensioner pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the tensioner pulley and idler pulley.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.



90. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


    A162367
  1. Install the front outer cowl top panel sub-assembly with the 7 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A162368
  1. Install the 2 clips.

  1. Install the fuel pump resistor with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



91. INSTALL NO. 1 COWL TOP TO COWL BRACE INNER


    A162366
  1. Install the No. 1 cowl top to cowl brace inner.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



92. INSTALL FRONT WIPER MOTOR AND LINK


    I035791E01
  1. Install the wiper motor & link assembly with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



93. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    A165365
  1. Push the ventilator louver in the direction indicated by the arrow in the illustration. Attach the 6 claws to install the ventilator louver.



94. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, and stop the windshield wiper motor assembly to the automatic stop position.



    E058837E18
  1. Scrape off the serration part of the wiper arm with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    I035782E01
  1. Install the front wiper arm LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 14.8 ft.*lbf }

    HINT:
    Hold down the arm hinge by hand to fasten the nut.



95. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
  1. Scrape off the serration part of the wiper arm with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    I035783E01
  1. Install the front wiper arm RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold down the arm hinge by hand to fasten the nut.

  1. Operate the wiper while running the water or the washer fluid over the window, and check the wiping condition and that the front wiper does not hit against the vehicle body.



96. INSTALL FRONT WIPER ARM HEAD CAP


    A165364E01
  1. Install the front wiper arm head caps.



97. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



98. ADD ENGINE OIL
  1. Add clean engine oil and install the oil filler cap.

    Engine oil:

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    5W-30

    Capacity: 
    Item
    Standard Condition
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 lmp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 lmp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 lmp. qts)



99. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Remove the air drain cock plug from the water inlet housing.



    A162799E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    11.3 liters (12.0 US qts, 10.0 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



100. ADD AUTOMATIC TRANSAXLE FLUID


101. CHECK AUTOMATIC TRANSAXLE FLUID

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. Park the vehicle on a level surface and set the parking brake.



    D025120E05
  1. With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put the dipstick back all the way.

  1. Take out the dipstick again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
    If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
    If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.



102. ADD POWER STEERING FLUID


103. BLEED POWER STEERING FLUID
  1. Check the fluid level .

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the steering wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the steering wheel left or right to the full lock position and keep it in that position for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.

    2. Repeat this procedure several times.

  1. Stop the engine.



    C137876E01
  1. Check for foaming or emulsification.

    HINT:
    If the system has to be bled twice because of forming or emulsification, be sure to check for fluid leaks in the system.

  1. Check the fluid level .



104. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    3. Turn the Techstream main switch on.

    4. Select the following menu items: Power train / Engine and ECT / Active Test / Control the Fuel Pump Speed.

    5. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, ECM and wiring connector.

  1. Inspect for fuel leaks (*1).

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



105. INSPECT FOR ENGINE OIL LEAK


106. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.



    A161453
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



107. INSPECT FOR EXHAUST GAS LEAK


108. CHECK SHIFT LEVER POSITION


    C099453E01
  1. Loosen the 2 bolts of the park/neutral position switch and move the shift lever to the N position.

  1. Align the groove with the neutral basic line.

  1. Hold the switch in position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. After adjustment, perform the inspection described in park/neutral position switch assembly operation.



109. CHECK AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
(Click here).



110. CHECK IGNITION TIMING
  1. Warm up the engine.

  1. When using the Techstream:
    Check the ignition timing.

    1. Connect Techstream to the DLC3.

    2. Enter DATA LIST mode with the Techstream.

      Ignition timing:
      8 to 12° BTDC at idle

      HINT:
      Refer to the Techstream operator's manual for help when selecting the DATA LIST.



    A122830E14
  1. When not using the Techstream:
    Check the ignition timing.

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor is turned off.

    2. Remove the V-bank cover.



    3. A132997
    4. Pull out the red lead wire harness.

    5. Connect the tester terminal of the timing light to the red lead wire as shown in the illustration.

      NOTICE:
      Use a timing light which can detect the first signal.

    6. Check the ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC at idle

      NOTICE:
      When checking the ignition timing, the transmission should be in neutral.

      HINT:
      Run the engine at 1000 to 1300 rpm for 5 seconds, and then check that the engine rpm returns to idle speed.

    7. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    8. Check the ignition timing at idle.

      Ignition timing:
      7 to 24° BTDC at idle

    9. Confirm that the ignition timing moves to the advanced angle side when the engine rpm is increased.

    10. Remove the timing light.



111. CHECK ENGINE IDLE SPEED
  1. Warm up the engine.

  1. When using the Techstream:
    Check the idle speed.

    1. Connect the Techstream to the DLC3.

    2. Enter DATA LIST mode with the Techstream.

      Idle speed:
      600 to 700 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in neutral.
      2. Check the idle speed with the cooling fan off.
      3. Switch off all accessories and air conditioning before connecting the Techstream.

      HINT:
      Refer to the Techstream operator's manual for further details.



    A122830E15
  1. When not using the Techstream:
    Check the idle speed.

    1. Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Check the idle speed.

      Idle speed:
      600 to 700 rpm



112. CHECK CO/HC
  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idling.

  1. Check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    Check regulations and restrictions in your area when performing 2 mode CO/HC concentration testing (engine check at both idle speed and at 2500 rpm).
    If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.


    1. Check air fuel ratio sensor and heated oxygen sensor operation.

    2. See the table below for possible causes, and then inspect and repair.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty fuel pressure regulator
        2. Defective ECT sensor
        3. Defective MAF meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor



113. CHECK FUNCTION OF THROTTLE BODY ASSEMBLY
  1. Listen to the throttle control motor operating sounds.

    1. Turn the ignition switch to ON.

    2. When pressing the accelerator pedal position sensor lever, listen to the running motor. Make sure that no friction noise comes from the motor.
      If friction noise exists, replace the throttle body.

  1. Inspect the throttle position sensor.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Check that the MIL turns off.

    4. Turn the Techstream to ON.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position.

    6. Depress the accelerator pedal. When the throttle valve is fully opened, check that the value of Throttle Position is within the specification.

      Standard throttle valve opening percentage:
      60% or more

      If the percentage is less than 60%, replace the throttle body.

      NOTICE:
      When checking the throttle valve opening percentage, the transmission should be in neutral.



114. INSTALL FRONT FENDER APRON SEAL RH


    A162371
  1. Install the front fender apron seal RH with the 2 bolts and clip.



115. INSTALL FRONT FENDER APRON SEAL LH


    A162370
  1. Install the front fender apron seal LH with the 2 bolts and clip.



116. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY


    A162362
  1. Install the No. 1 engine under cover sub-assembly with the 8 bolts and 4 clips.



117. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.



118. CHECK ABS SPEED SENSOR SIGNAL
Click here


119. RESET MEMORY

HINT:
Click here.