Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C0200/31    Right Front Wheel Speed Sensor Signal

DTC    C0205/32    Front Speed Sensor LH Circuit

DTC    C1235/35    Foreign Object is Attached on Tip of Front Speed Sensor RH

DTC    C1236/36    Foreign Object is Attached on Tip of Front Speed Sensor LH

for Preparation Click here


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the ABS control system. The front and rear rotors have 48 serrations each.
F000010E12
When the rotors rotate, the magnetic field emitted by the permanent magnet in the speed sensor generates AC voltage. Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the ECU to detect the speed of each wheel.

DTC Code
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When any of the following is detected:
  1. At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 1 sec. or more.
  2. Momentary interruption of sensor signal of faulty wheel occurs 7 times or more.
  3. Sensor signal circuit is open for 0.5 sec. or more.
  1. Right front and left front speed sensor
  2. Each speed sensor circuit
  3. Speed sensor rotor
  4. Sensor installation
C1235/35
C1236/36
When either of the following is detected:
  1. At a vehicle speed of 20 km/h (12 mph) or more, sensor signal of faulty wheel generated noise for 5 sec. or more.
  2. At a vehicle speed of 10 km/h (6 mph) or more, and noise is input once per rotor rotation for 15 sec. or more.
  1. Right front and left front speed sensor
  2. Sensor installation

HINT:
  1. DTC C0200/31 and C1235/35 are for the right front speed sensor.
  2. DTC C0205/32 and C1236/36 are for the left front speed sensor.


WIRING DIAGRAM


F040884E11


INSPECTION PROCEDURE

1.READ VALUE ON TECHSTREAM (FRONT SPEED SENSOR)
  1. Connect Techstream to the DLC3.

  1. Start the engine.

  1. Select the Data List mode on Techstream.

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    FR Wheel Speed
    Wheel speed sensor (FR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    FL Wheel Speed
    Wheel speed sensor (FL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed

  1. Check that there is no difference between the speed value output from the speed sensor displayed on Techstream and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference from the displayed speed value.

    HINT:
    There is tolerance of +- 10 % in the speedometer indication.



NG
Go to step 3
OK


2.CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS


  1. INSPECTION USING OSCILLOSCOPE

    1. Connect the oscilloscope to terminal FR+ and FR- or FL+ and FL- of the skid control ECU.



    2. W004200E17
    3. Drive the vehicle at about 19 mph (30 km/h), and check the signal waveform.

      OK:
      A waveform as shown in a figure should be output.

      HINT:
      1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the fluctuation in the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to the speed sensor rotor's scratches, looseness or foreign matter attached to it.

      NOTICE:
      When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
Go to step 6
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 

3.INSPECT FRONT SPEED SENSOR
  1. Make sure that there is no looseness at the connectors' locking part and connecting part of connector.

  1. Disconnect the speed sensor connector.



    C093876E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    A3-1 (FL+) - A3-2 (FL-)
    0.6 to 2.5 kΩ
    RH:
    Tester Connection
    Specified Condition
    A4-1 (FR+) - A4-2 (FR-)
    0.6 to 2.5 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    A3-1 (FL+) - Body ground
    10 kΩ or higher
    A3-2 (FL-) - Body ground
    10 kΩ or higher
    RH:
    Tester Connection
    Specified Condition
    A4-1 (FR+) - Body ground
    10 kΩ or higher
    A4-2 (FR-) - Body ground
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR - SKID CONTROL ECU)
  1. Disconnect the skid control ECU connector and the front speed sensor connector.



    C136018E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    S3-18 (FL+) - A3-1 (FL+)
    Below 1 Ω
    S3-4 (FL-) - A3-2 (FL-)
    Below 1 Ω
    RH:
    Tester Connection
    Specified Condition
    S3-3 (FR+) - A4-1 (FR+)
    Below 1 Ω
    S3-17 (FR-) - A4-2 (FR-)
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    S3-18 (FL+) - Body ground
    10 kΩ or higher
    S3-4 (FL-) - Body ground
    10 kΩ or higher
    RH:
    Tester Connection
    Specified Condition
    S3-3 (FR+) - Body ground
    10 kΩ or higher
    S3-17 (FR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS


  1. INSPECTION USING OSCILLOSCOPE

    1. Connect the oscilloscope to terminal FR+ and FR- or FL+ and FL- of the skid control ECU.



    2. W004200E18
    3. Drive the vehicle at about 19 mph (30 km/h), and check the signal waveform.

      OK:
      A waveform as shown in a figure should be output.

      HINT:
      1. As the vehicle speed (Wheel revolution speed) increases, a cycle of the waveform narrows and the fluctuation in the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to the speed sensor rotor's scratches, looseness or foreign matter attached to it.

      NOTICE:
      When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
Go to step 6
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 

6.CHECK FRONT SPEED SENSOR INSTALLATION


    BR03795E45
  1. Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly. There is no clearance between the sensor and the front steering knuckle.

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

NOTICE:
Check the speed sensor signal after the replacement (Click here).



NG
INSTALL FRONT SPEED SENSOR CORRECTLY
OK


7.CHECK FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after the replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


8.CHECK SPEED SENSOR ROTOR
  1. Remove the front drive shaft (Click here).



    R000948E06
  1. Check the sensor rotor serrations.

    OK:
    No scratches, missing teeth or foreign matter on the rotors.

    HINT:
    If there is foreign matter in the rotor, remove it and check the output waveform after reassembly.

    NOTICE:
    1. Check the speed sensor signal after the replacement (Click here).
    2. When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
REPLACE FRONT DRIVE SHAFT ASSEMBLY (SPEED SENSOR ROTOR)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY