VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT BULB CHECK |
![]() |
Check the warning lights.
Release parking brake pedal.
When the ignition switch is turned to the ON position, check that the ABS warning light, BRAKE warning light, VSC warning light, TRAC OFF indicator light (2WD) and SLIP indicator light stay on for approx. 3 seconds.
| Trouble Area | See procedure |
| ABS warning light circuit |
Click here or Click here
|
| VSC warning light circuit |
Click here or Click here
|
| BRAKE warning light circuit |
Click here
|
| TRAC OFF indicator light circuit (2WD) |
Click here or Click here
|
| SLIP indicator light circuit |
Click here or Click here
|
| SENSOR SIGNAL CHECK BY TEST MODE (SIGNAL CHECK) (WHEN USING TECHSTREAM): |
When having replaced the skid control ECU and/or yaw rate and deceleration sensor, perform zero point calibration of the yaw rate and deceleration sensor.
Procedures for test mode.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Check that the steering wheel is in the straight ahead position and move the shift lever to the P position.
Turn the ignition switch to the ON position.
Set Techstream to test mode (select "Signal Check").
![]() |
Check that the ABS warning light and VSC warning light blink (test mode).
| Trouble Area | See procedure |
| ABS warning light |
Click here or Click here
|
| VSC warning light |
Click here or Click here
|
| MASTER CYLINDER PRESSURE SENSOR CHECK (WHEN USING TECHSTREAM): |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second or more.
Check the ABS warning light stays on for 3 seconds.
| SPEED SENSOR CHECK (WHEN USING TECHSTREAM): |
Check the backward signal.
Drive the vehicle in reverse for more than 1 second at 3 km/h (2 mph) or higher.
Check the forward signal.
Drive the vehicle straight forward. Drive the vehicle at a speed of 45 km/h (28 mph) or higher for several seconds and check that the ABS warning light goes off.
![]() |
Stop the vehicle.
| YAW RATE SENSOR CHECK (WHEN USING TECHSTREAM): |
Check the output of the yaw rate sensor.
Move the shift lever to the D position, drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.
Stop the vehicle and move the shift lever to the P position. Check that the skid control buzzer sounds for 3 seconds.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| DTC Code | Detection Item | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Speed sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Speed sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Speed sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Speed sensor rotor |
| C1279/79 | Acceleration sensor output voltage malfunction |
|
| C1281/81 | Master cylinder pressure sensor output malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| C0371/71 | Yaw rate sensor | Yaw rate and deceleration sensor |
| SENSOR SIGNAL CHECK BY TEST MODE (SIGNAL CHECK) (WHEN USING SST CHECK WIRE): |
When having replaced the skid control ECU and/or yaw rate and deceleration sensor, perform zero point calibration of the yaw rate and deceleration sensor.
Procedures for test mode.
Turn the ignition switch off.
Check that the steering wheel is in the straightahead position and move the shift lever to the P position.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() |
Check that the ABS warning light and VSC warning light blink (test mode).
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here or Click here
|
| VSC warning light circuit |
Click here or Click here
|
| MASTER CYLINDER PRESSURE SENSOR CHECK (WHEN USING SST CHECK WIRE): |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second or more.
Check the ABS warning light stays on for 3 seconds.
| SPEED SENSOR CHECK (WHEN USING SST CHECK WIRE): |
Check the speed sensor signal.
Drive the vehicle straight forward. Drive the vehicle at a speed of 45 km/h (28 mph) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| YAW RATE SENSOR CHECK (WHEN USING SST CHECK WIRE): |
Check the zero point voltage of the yaw rate sensor.
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
Check the output of the yaw rate sensor.
Move the shift lever to the D position, drive the vehicle at a speed of approximately 3 mph (5 km/h), and turn the steering wheel either to the left or right 90° or more until the vehicle makes 180° turn.
Stop the vehicle and move the shift lever to the position. Check that the skid control buzzer sounds for 3 seconds.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION |
| DTC Code | Detection Item | Trouble Area |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH | Speed sensor rotor |
| C1276/76 | Abnormal change in output signal of front speed sensor LH | Speed sensor rotor |
| C1277/77 | Abnormal change in output signal of rear speed sensor RH | Speed sensor rotor |
| C1278/78 | Abnormal change in output signal of rear speed sensor LH | Speed sensor rotor |
| C1279/79 | Acceleration sensor output voltage malfunction |
|
| C1281/81 | Master cylinder pressure sensor output malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| C0371/71 | Yaw rate sensor | Yaw rate and deceleration sensor |