Home › BRAKE › BRAKE › REAR DISC BRAKE

REAR DISC BRAKE > REASSEMBLY

for Preparation Click here



1. INSTALL REAR DISC


    F041543E13
  1. Aligning the matchmarks, install the rear disc.

    HINT:
    Select the installation position where the disc has the minimum runout.



2. INSPECT DISC RUNOUT
  1. Inspect rear axle hub bearing backlash and deviation.

    1. for 2WD: Click here
    2. for 4WD: Click here

  1. Install the disc with the 5 hub nuts.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



    C190875E01
  1. Using a dial indicator, measure the disc runout 10 mm (0.39 in.) away from the outer edge of the disc.

    Maximum disc runout:
    0.10 mm (0.0039 in.)

  1. If the runout exceeds the maximum value, change the installation position of the disc to minimize runout. If the runout exceeds the maximum even when the installation position is changed, grind the disc. If the disc thickness is less than the minimum, replace the rear disc.

  1. Remove the 5 hub nuts.



3. ADJUST PARKING BRAKE SHOE CLEARANCE


    F040026E02
  1. Temporarily install the hub nuts.

  1. Remove the hole plug, and turn the adjuster and expand the shoes until the disc locks.

  1. Contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches

  1. Check that the brake disc rotates smoothly.

  1. Install the hole plug.



4. TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG
  1. Temporarily install the rear disc brake bleeder plug to the disc brake cylinder assembly rear LH.



5. INSTALL REAR DISC BRAKE BLEEDER PLUG CAP


6. INSTALL PISTON SEAL


    C189006E01
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of a new piston seal.

  1. Install the piston seal to the disc brake cylinder assembly rear LH.

    NOTICE:
    Securely install the piston seal to the groove of the disc brake cylinder assembly rear LH.



7. INSTALL REAR DISC BRAKE PISTON


    C190876E01
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.

  1. Install the cylinder boot to the rear disc brake piston.

  1. Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake piston, and install it to the disc brake cylinder assembly rear LH.

    NOTICE:
    Do not install the piston forcibly in the disc brake cylinder.



8. INSTALL CYLINDER BOOT


    G024294
  1. Install the cylinder boot to the rear disc brake cylinder sub-assembly.

    NOTICE:
    Install the boot securely to the grooves of the cylinder and piston.

  1. Using a screwdriver, install the set ring.

    NOTICE:
    Do not damage the cylinder boot.



9. INSTALL REAR DISC BRAKE BUSH DUST BOOT


    C190376E01
  1. Apply a light layer of lithium soap base glycol grease to the contact and inner surfaces of 2 new rear disc brake bush dust boots.

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bush dust boot.

  1. Install the 2 rear disc brake bush dust boots to the rear disc brake cylinder mounting LH.



10. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN


    C189004E01
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and sealing surfaces of the 2 rear disc brake cylinder slide pins.

  1. Install the 2 rear disc brake cylinder slide pins to the rear disc brake cylinder mounting LH.