Home › BODY › ENGINE HOOD / DOOR › SLIDE DOOR (w/o Power Slide Door)

SLIDE DOOR (w/o Power Slide Door) > INSTALLATION

for Preparation Click here



1. INSTALL SLIDE DOOR ROLLER ASSEMBLY UPPER


    B067498
  1. Apply MP grease to the rotating areas of the roller.

  1. Install the roller with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



2. INSTALL SLIDE DOOR HINGE ASSEMBLY CENTER LH


    B067496E01
  1. Apply MP grease to the rotating areas of the hinge.

  1. Install the hinge with the 3 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



3. INSTALL SLIDE DOOR ROLLER ASSEMBLY LOWER LH


    B067499
  1. Apply MP grease to the rotating areas of the roller.

  1. Install the roller lower with the 3 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



4. INSTALL SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH


    B067501E01
  1. Apply MP grease to the sliding and rotating areas of the lock.

  1. Install the lock with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 cables.



5. INSTALL SLIDE DOOR RAILS
  1. Install the rail center with the 3 screws.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Install the rear side rail with the 2 screws.

    Torque:
    19.5 N*m{ 200 kgf*cm , 14 ft.*lbf }

  1. Install the rail upper with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 8 ft.*lbf }

  1. Install the roof headlining (Click here).



6. INSTALL SLIDE DOOR


    B069212E01
  1. Put in the slide door hinge center from the rear part of the slide door rail center.



    B069213E02
  1. Move the slide door forward and then put in the slide door roller upper into the cut area of the slide door rail upper.



    B060924E01
  1. Rotate the base of the slide door roller lower in the direction indicated by arrow in the illustration and then put in the roller lower into the cut area of the rail lower of the body.



    B067901
  1. Install the open stop with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    B069321E02
  1. Install the bracket center No. 2 with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    B068589E01
  1. Install the rail end moulding.

  1. Install the upper rail cushion to the rail upper.



    B068386
  1. Install the wire with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 connectors.



7. REPLACE SLIDE DOOR HALF OPEN STOPPER SUB-ASSEMBLY


    B067518
  1. Install the half open stopper with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the control cable to the half open stopper.



    B069065E01
  1. Connect the control cable to the open striker with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. REPLACE SLIDE DOOR HALF OPEN STOPPER CONTROL ASSEMBLY


    B067521E01
  1. Install the control cable, as shown in the illustration.

    Dimension (A):
    3.9 +- 1.5 mm (0.154 +- 0.059 in.)



    B067520E02
  1. Install the half open stopper control with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



9. REPLACE SLIDE DOOR OPEN STRIKER LH


    B067519E01
  1. Install the open striker with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



10. REPLACE SLIDE DOOR OPEN STRIKER RH

HINT:
Use the same procedures for the LH side.



11. REPLACE SLIDE DOOR OPEN STOP LH


    B067901
  1. Install the open stop with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



12. REPLACE SLIDE DOOR OPEN STOP RH

HINT:
Use the same procedures for the LH side.