Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Door Lock Control Function does not Operate

for Preparation Click here


DESCRIPTION

The door control receiver receives a signal from the transmitter and sends this signal to the multiplex network body ECU. Then, the multiplex network body ECU controls operation of the door locks and power windows.
Then, the power slide door ECU causes the power slide door to open or close when it receives a signal from the transmitter via the door control receiver and multiplex network body ECU. Also, the power back door ECU causes the power back door to open or close when it receives a signal from the transmitter via the door control receiver and multiplex network body ECU.

WIRING DIAGRAM


B129147E02


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check the wireless door lock control system (Click here).



OK
END
NG


2.REPLACE TRANSMITTER BATTERY
  1. After replacing the transmitter battery with a new or normal one, check that the doors can lock and unlock, using the transmitter LOCK/UNLOCK switch.



OK
REPLACE TRANSMITTER BATTERY
NG


3.CHECK WIRELESS DOOR LOCK (STANDARD OPERATION)
  1. Using the transmitter to LOCK/UNLOCK doors in standard operation, check that the doors can lock and unlock.

    NOTICE:
    Standardized test procedure: Press the transmitter switch for 1 second, directing the beam to driver's door outside handle from a distance of 1 m (39.4 in.). The transmitter should be pointed directly at the door handle, i.e at 90° angle to the vehicle body.



NG
REPLACE DOOR CONTROL TRANSMITTER
OK


4.CHECK WIRELESS DOOR LOCK BUZZER
  1. Check that the wireless door lock buzzer sounds.

    Result 
    Condition
    Proceed to
    Buzzer sounds
    A
    Buzzer does not sound
    Go to "No Answer-Back (Hazard Warning Light and Wireless Door Lock Buzzer)" (Click here)


A


5.SWITCH TO SELF DIAGNOSTIC MODE
  1. When using the Techstream:
    Switch to the self-diagnostic mode on the Techstream.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch ON and push the Techstream main switch ON.

      HINT:
      Please refer to the Techstream operator's manual for further details.

  1. When not using the Techstream:
    Switch to the self-diagnostic mode by operating the ignition key cylinder.

    1. Insert the key into the ignition key cylinder and remove it under the initial vehicle condition (Click here).

    2. Within 5 seconds after the above step, insert the key into the ignition key cylinder and turn the ignition switch from ON to OFF once.

    3. Within 30 seconds after the above step, turn the ignition switch from ON to OFF 9 times.

      NOTICE:
      If operation has failed, the system will return to the normal mode.

      HINT:
      1. Operation of the ignition switch from OFF to ON will end the self-diagnostic mode.
      2. Do not lock or unlock doors during the self-diagnostic mode.



    B110075E01
  1. Check that the system has switched to self-diagnostic mode by the answer-back of the wireless door lock buzzer sound.



NG
Go to step 10
OK


6.CHECK SELF DIAGNOSTIC MODE


  1. Inspect the diagnosis outputs when the door control transmitter switch is held down (The diagnosis outputs can be checked with the sound of the wireless door lock buzzer).


    B110076E13


    Result 
    Condition
    Proceed to
    Normal waves patterns from the wireless door lock buzzer are output for LOCK, UNLOCK, PANIC or PWR DOOR
    A
    Unmatched recognition code is output.
    B
    No diagnostic outputs are recorded
    C



A
Go to step 18

C
Go to step 8
B


7.REGISTER RECOGNITION CODE
  1. Check that the system can switch to rewrite mode or add mode and also check wether a recognition code can be registered.



NG
Go to step 9
OK

END 

8.CHECK DOOR CONTROL RECEIVER
  1. When a new or normal door control transmitter switch for the same type vehicle is held down, check that a diagnosis of unmatching recognition code is output.



NG
Go to step 14
OK

REPLACE DOOR CONTROL TRANSMITTER 

9.REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver with normal one.

    OK:
    The system returns to normal operation.



NG
Go to step 18
OK

REPLACE DOOR CONTROL RECEIVER 

10.CONFIRM SELF DIAGNOSTIC MODE
  1. When the input method for switching the system to self-diagnostic mode is correct, proceed to A.

  1. When the input method for switching the system to self-diagnostic mode is incorrect, proceed to B.



B
Go to step 5
A


11.READ VALUE USING DATA LIST
  1. Using the Techstream, check the DATA LIST for proper functioning of the un-lock warning switch.

    BODY (Multiplex network body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Un-lock warning switch signal/ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -



OK
Go to step 14
NG


12.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY


    B113629E05
  1. Inspect the resistance of the un-lock warning switch.

    Standard resistance:
    Terminal No.
    Condition
    Specified Condition
    1 - 2
    Switch free
    (Key removed)
    10 kΩ or higher
    1 - 2
    Switch pushed
    (Key set)
    Below 1 Ω



NG
REPLACE UN-LOCK WARNING SWITCH ASSEMBLY
OK


13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK BODY ECU - UN-LOCK WARNING SWITCH)


    B110078E06
  1. Disconnect the B6 ECU connector and K4 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Symbol (Terminal No.)
    Specified Condition
    KSW (B6-21) - K4-2
    Below 1 Ω
    KSW (B6-21) - Body ground
    10 kΩ or higher
    K4-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BODY GROUND)


    B059092E04
  1. Disconnect the D4 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard:
    Symbol (Terminal No.)
    Specified Condition
    +B (D4-5) - Body ground
    10 to 14 V
    GND (D4-1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK DOOR CONTROL RECEIVER (OUTPUT)


    B051174
  1. Reconnect the D4 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard:
    Terminal No.
    Condition
    Specified Condition
    RDA (D4-2) - Body ground
    No key in ignition key cylinder, all doors closed and each transmitter switch OFF → ON
    Below 1 V → Approx. 6 to 7 V → Below 1 V



OK
Go to step 17
NG


16.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK BODY ECU - DOOR CONTROL RECEIVER)


    B068693E03
  1. Disconnect the D4 receiver connector and B9 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Symbol (Terminal No.)
    Specified Condition
    RDA (D4-2) - RDA (B9-12)
    Below 1 Ω
    RDA (D4-2) - Body ground
    10 kΩ or higher
    RDA (B9-12) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver with normal one.

    OK:
    The system returns to normal operation.



OK
REPLACE DOOR CONTROL RECEIVER
NG


18.REPLACE MULTIPLEX NETWORK BODY ECU
  1. Replace the multiplex network body ECU with normal one.

    OK:
    The system returns to normal operation.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MULTIPLEX NETWORK BODY ECU