Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

ANTI-LOCK BRAKE SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

If the ECU detects a trouble, it turns on the brake warning light at the same time of prohibiting ABS control.
At this time, the ECU records a DTC in memory.
Connect terminals TC and CG of the DLC3 to make the brake warning light blink and output the DTC.

WIRING DIAGRAM


C160966E01


INSPECTION PROCEDURE

1.CHECK DTC
  1. Check if the ABS DTC is output (Click here).

    Result:

    Condition
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2.INSPECT SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
  1. Check the skid control ECU connector's connecting condition.

    OK:
    The connector should be securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    10 to 14 V



NG
INSPECT CHARGING SYSTEM
OK


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL VOLTAGE)
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the on position.



    C122930E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S3-3 (IG1) - Body ground
    Ignition switch ON (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)
  1. Disconnect the skid control ECU connector.



    C058919E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-1 (GND1) - Body ground
    Below 1 Ω
    S3-23 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.INSPECT PARKING BRAKE SWITCH
  1. Disconnect the parking brake switch connector.



    C106667E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P6-1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    P6-1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH
OK


7.CHECK HARNESS AND CONNECTOR
  1. Disconnect the skid control ECU connector and parking brake switch.



    C122972E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-12 (PKB) - P6-1
    Below 1 Ω
    S3-12 (PKB) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PKB CIRCUIT)
OK


8.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
  1. Remove the reservoir tank cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.



    C119428E01
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-1 - B1-2
    Float up
    (Switch OFF)
    1.9 to 2.1 kΩ
    B1-1 - B1-2
    Float down
    (Switch ON)
    Below 1 Ω

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
OK


9.INSPECT HARNESS AND CONNECTOR (BETWEEN BRAKE FLUID LEVEL WARNING SW AND COMBINATION METER)
  1. Disconnect the combination meter connector.



    C119429E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    C10-13 - B1-1
    Below 1 Ω
    C10-13 - Body ground
    10 kΩ or higher
    B1-2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH CIRCUIT)
OK


10.CHECK HARNESS AND CONNECTOR (BETWEEN SKID CONTROL ECU AND COMBINATION METER ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the combination meter connector.



    C111162E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-19 (BRL) - C10-14
    Below 1 Ω
    S3-19 (BRL) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT COMBINATION METER ASSEMBLY
  1. Check the combination meter assembly (Click here).

HINT:
If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY
OK

REPLACE BRAKE ACTUATOR ASSEMBLY