Home › BODY › MIRROR › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Position Sensor Circuit

for Preparation Click here


DESCRIPTION

  1. When SET and 1 or 2 are pressed, the position sensor detects the mirror position and sends the signal to the outer mirror control ECU. Then when position 1 or 2 is pressed, the outer mirror control ECU drives the mirror motor based on the memorized sensor positions.

    HINT:
    The power mirror control system is part of the multiplex communication system. This system features shared communication wiring that reduces the wiring complexity of the communication lines. The first step in any repair is to confirm the proper operation of the communication system. Proceed with troubleshooting after the communication has been verified (See Multiplex Communication System) (Click here).


WIRING DIAGRAM


B112560E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Ignition switch on.

  1. Read the DATA LIST according to the display on the tester.


Mirror L/Mirror R 
Tester Display
Measurement Item/Range
Normal condition
Diagnostic Note
Mirror Position Sensor (V)
Vertical mirror position/MIN: 0, MAX 5 V
Within range from 0 to 5 V
-
Mirror Position Sensor (H)
Horizontal mirror position/MIN: 0, MAX 5 V
Within range from 0 to 5 V
-

OK:
Tester displayed is 0 V to 5 V.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - OUTER MIRROR CONTROL ECU)


    B112554E03
  1. Disconnect the O10 or O12 ECU connector.

  1. Disconnect the O13 or O14 outer mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    O13-15 - O10-5 (DVC) (*1)
    Always
    Below 1 Ω
    O14-15 - O12-5 (PVC) (*2)
    Always
    Below 1 Ω
    O13-16 - O10-13 (HSSR) (*1)
    Always
    Below 1 Ω
    O14-16 - O12-13 (HSSR) (*2)
    Always
    Below 1 Ω
    O13-17 - O10-6 (VSSR) (*1)
    Always
    Below 1 Ω
    O14-17 - O12-6 (VSSR) (*2)
    Always
    Below 1 Ω
    O13-18 - O10-14 (DE2) (*1)
    Always
    Below 1 Ω
    O14-18 - O12-14 (PE2) (*2)
    Always
    Below 1 Ω
    O10-5 (DVC) - Body ground (*1)
    Always
    10 kΩ or higher
    O12-5 (PVC) - Body ground (*2)
    Always
    10 kΩ or higher
    O10-13 (HSSR) - Body ground (*1)
    Always
    10 kΩ or higher
    O12-13 (HSSR) - Body ground (*2)
    Always
    10 kΩ or higher
    O10-6 (VSSR) - Body ground (*1)
    Always
    10 kΩ or higher
    O12-6 (VSSR) - Body ground (*2)
    Always
    10 kΩ or higher
    O10-14 (DE2) - Body ground (*1)
    Always
    10 kΩ or higher
    O12-14 (PE2) - Body ground (*2)
    Always
    10 kΩ or higher

    *1: LH side
    *2: RH side



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU