POWER SLIDE DOOR SYSTEM > OPERATION CHECK |
| CHECK OPENING OPERATION |

Conditions necessary for the power slide door to open:
Power slide door main switch is in the ON position.
Slide door is positioned between the fully closed position and the half-open position (When the slide door is fully closed, the door must be unlocked).
Shift lever is in the P position when the ignition switch is ON (When the ignition switch is OFF, power slide door can operate in any position of the shift lever).
No key is inserted into the ignition key cylinder when the transmitter is used.
Fuel lid is closed.
![]() |
Press the satellite switch for the power slide door.
Check that the power slide door opens when the switch has been pressed for more than 0.8 seconds.
Check that the power slide door reverses operation and moves to the fully closed position when the same switch is pressed again during opening.
![]() |
Press the transmitter switch for the power slide door.
Check that the power slide door opens when the switch has been pressed for more than 0.8 seconds.
Check that the power slide door reverses operation and moves to the fully closed position when the same switch is pressed again during opening.
![]() |
Press the power slide door control switch.
Check that the power slide door opens when the switch is pressed.
Check that the power slide door reverses operation and moves to the fully closed position when the same switch is pressed again during opening.
![]() |
Pull the outside / inside handle for the power slide door.
Check that the power slide door opens when the handle is pulled.
Check that the power slide door reverses operation and moves to the fully closed position when the same handle is pulled again during opening.
| CHECK CLOSING OPERATION |

Conditions necessary for the power slide door to close:
Power slide door main switch is in the ON position.
Slide door is positioned between the fully open position and the half-open position.
No key is inserted into the ignition key cylinder when the transmitter is used.
![]() |
Press the satellite switch for the power slide door.
Check that the power slide door closes when the switch has been pressed for more than 0.8 seconds.
Check that the power slide door reverses operation and moves to the fully open position when the same switch is pressed again during closing.
![]() |
Press the transmitter switch for the power slide door.
Check that the power slide door closes when the switch has been pressed for more than 0.8 seconds.
Check that the power slide door reverses operation and moves to the fully open position when the same switch is pressed again during closing.
![]() |
Press the power slide door control switch.
Check that the power slide door closes when the switch is pressed.
Check that the power slide door reverses operation and moves to the fully open position when the same switch is pressed again during closing.
![]() |
Pull the outside / inside handle for the power slide door.
Check that the power slide door closes when the handle is pulled.
Check that the power slide door reverses operation and moves to the fully open position when the same handle is pulled again during closing.
| CHECK JAM PROTECTION FUNCTION |
![]() |
[a] Check the jam protection function while the power slide door is closing.
Fully open the slide door.
Press the switch that operates the power slide door to activate it to close.
![]() |
While the slide door is closing, press the touch sensor using the handle of a hammer or the equivalent.
![]() |
Check that the jam protection function is immediately activated and the power slide door reverses operation to the fully open position.
![]() |
[b] Check the jam protection function while the power slide door is opening.
Fully open the slide door.
Press the switch that operates the power slide door to activate it to close.
![]() |
While the slide door is opening, hold the slide door by using a tire or equivalent, as shown in the illustration, so that the operating speed decreases.
![]() |
Check that the jam protection function is immediately activated and the power slide door reverses operation to the fully closed position.
![]() |
Check operation of the power slide door when the jam protection function is consecutively activated.
Check that power slide door operation is cancelled and switched to manual operation mode (not electrically controlled) when the jam protection function has been activated 2 or more consecutive times and when the 2nd or most recent activation has occurred during closing.
| CHECK FUEL LID STOPPER SYSTEM |

Check that the slide door cannot be opened when the fuel lid is open.
Check that the power slide door is switched to manual operation mode when the fuel lid is opened while the power slide door is moving.
| SLIDE DOOR HALF-OPEN STOPPER SYSTEM |

Check that the slide door is forced to stop at approx. 105 mm (4.13 in.) from the fully open position when the window is open 150 mm (5.91 in.) or more.
| SLIDE DOOR FULL OPEN STOP LOCK |

Check that the slide door is fixed at the fully open position by the slide door full open stop lock when fully open.
| CHECK WARNING BUZZER |
Check the warning buzzer sounding function that notifies that the power slide door is open or is opening while the vehicle is moving (when the shift lever is moved into any position except the P position).
While the slide door is open, check that the warning buzzer sounds at a cycle of 0.3 seconds if the shift lever is moved into any position except the P position with the ignition switch ON.
Turn the ignition switch ON and move the shift lever into any position except the P position. Check that the warning buzzer sounds at a cycle of 0.3 seconds when the power slide door system is activated to open using the switches or handles.
Check that the warning buzzer stops sounding when the slide door is fully closed or the shift lever is moved into the P position.