POWER BACK DOOR SYSTEM > OPERATION CHECK |
| CHECK OPENING OPERATION |

Conditions necessary for the power back door to open:
Power back door main switch is in the ON position.
Back door is positioned between the fully closed position and the half-open position (When the back door is fully closed, the door must be unlocked).
Shift lever is in the P position when the ignition switch is ON (When the ignition switch is OFF, power back door can operate in any position of the shift lever).
No key is inserted into the ignition key cylinder when the transmitter is used.
![]() |
Press the satellite switch for the power back door.
Check that the power back door is unlatched and then opens when the switch has been pressed for more than 0.8 seconds.
Check that the power back door reverses operation and moves to the fully closed position when the same switch is pressed again during opening operation.
![]() |
Press the transmitter switch for the power slide door.
Check that the power back door is unlatched and then opens when the switch has been pressed for more than 0.8 seconds.
Check that the power back door reverses operation and moves to the fully closed position when the same switch is pressed again during opening operation.
Pull the outside handle for the power back door.
Open the back door and pull the handle while it is opening. Check that the power back door immediately reverses operation and moves to the fully closed position.
| CHECK CLOSING OPERATION |

Conditions necessary for the power back door to close:
Power back door main switch is in the ON position.
Back door is positioned between the fully open position and the half-open position.
No key is inserted into the ignition key cylinder when the transmitter is used.
![]() |
Press the satellite switch for the power back door.
Check that the power back door closes when the switch has been pressed for more than 0.8 seconds.
Check that the power back door reverses operation and moves to the fully open position when the same switch is pressed again during closing operation.
![]() |
Press the transmitter switch for the power back door.
Check that the power back door closes when the switch has been pressed for more than 0.8 seconds.
Check that the power back door reverses operation and moves to the fully open position when the same switch is pressed again during closing operation.
Pull the strap on the power back door.
Check that the power back door starts closing when the back door is manually moved approximately 12 cm (4.7 in.) within 0.5 seconds by pulling the strap and continues to move to the fully closed position.
Check that the power back door reverses operation and moves to the fully open position when the outside handle is pulled during closing operation.
| CHECK JAM PROTECTION FUNCTION |
[A] Check the jam protection function while the power back door is closing.
Fully open the back door.
[a] Press the switch that operates the power back door to activate it to close, and perform procedure [b], [c] and [d] respectively.
![]() |
[b] While the back door is closing, press the touch sensor using the handle of a hammer or the equivalent, as shown in the illustration.
![]() |
[c] While the back door is closing, insert a tire or equivalent between the door panel and vehicle body, as shown in the illustration, in order to interrupt closing operation.
![]() |
[d] Check that the jam protection function is immediately activated and the power back door reverses operation to the fully open position.
[B] Check the jam protection function while the power back door is opening.
Fully close the back door.
Press the switch that operates the power back door to activate it to open.
![]() |
While the back door is opening, press the outside surface of the back door panel that is moving by hand so that the operating speed decreases, as shown in the illustration.
![]() |
Check that the jam protection function is immediately activated and the power back door reverses operation to the fully closed position.
![]() |
Check operation of the power back door when the jam protection function is activated consecutively.
Check that power back door operation is canceled and switched to manual operation mode (not electrically controlled) when the jam protection function has been activated 2 or more consecutive times and when the 2nd or most recent activation has occurred during closing.
| CHECK WARNING BUZZER |
Check the warning buzzer sounding function that notifies that the power back door is open or is opening while the vehicle is moving (when the shift lever is moved into any position except the P position).
While the back door is open, check that the warning buzzer sounds at a cycle of 0.3 seconds if the shift lever is moved into any position except the P position with the ignition switch ON.
Turn the ignition switch ON and move the shift lever into any position except the P position. Check that the warning buzzer sounds at a cycle of 0.3 seconds when the power back door system is activated to open using the switches.
Check that the warning buzzer stops sounding when the back door is fully closed or the shift lever is moved into the P position.
Check that the warning buzzer that notifies the start of opening of the power back door sounds at 2 cycles of 0.5 seconds when the power back door is activated to open.
| DOOR LOCK |
When the battery is reconnected:
The back door is locked and cannot be opened. Therefore, it is necessary to unlock the back door using the door control switch or transmitter switch.
| RESET |
When the back door w/ motor lock is replaced:
The ECU cannot receive a switch signal from the lock. This may cause the power back door system to enter fail-safe mode and DTC B2215 to set and also may make the system disabled.
When the lock is replaced, be sure to perform the following: first properly connect the lock, second clear the DTC using the Techstream and finally recheck that no DTC is output.
Reset the power back door system:
The power back door ECU records the fully open position and the fully closed position of the power back door in its memory and the power back door fully opens and fully closed based on this memory.
The power back door cannot operate without this memory. In the case where the battery has been removed, manually close the back door fully to reset the power back door system. However, if the battery is removed/installed when the back door is fully open, the power back door operates normally, thus the resetting the system is unnecessary.
Replacing drive unit will also cause the memory of the door positions to be last. Therefore, in such a case resetting the system is necessary.
Reset the power back door system as follows:
Fully close the power back door if opened.
Check that the back door fully open and fully close.