FRONT WHEEL ALIGNMENT > ADJUSTMENT |
| 1. INSPECT TIRE |
| 2. MEASURE VEHICLE HEIGHT |
![]() |
Bounce the vehicle at the corners up and down to stabilize the suspension and inspect the vehicle height.
| Front (A - B) | Rear (D - C) |
| 115.5 mm (4.55 in.) | -27.5 mm (-1.08 in.) |
| Front (A - B) | Rear (D - C) |
| 116 mm (4.57 in.) | -45.5 mm (-1.79 in.) |
| 3. INSPECT TOE-IN |
![]() |
Inspect the toe-in.
| Toe-in (total) | - |
| A + B: C - D: | -1.2' +/- 12' (-0.02° +/- 0.2°) -0.2 +/- 2 mm (-0.01 +/- 0.08 in.) |
| Toe-in (total) | - |
| A + B: C - D: | 2.4' +/- 12' (0.04° +/- 0.2°) 0.4 +/- 2 mm (0.02 +/- 0.08 in.) |
| 4. ADJUST TOE-IN |
Remove the rack boot set clips.
Loosen the tie rod end lock nuts.
Turn the right and left rack ends by an equal amount to adjust the toe-in.
![]() |
Make sure that the lengths of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
Place the boots on the seats and install the clips.
| 5. INSPECT WHEEL ANGLE |
![]() |
Turn the steering wheel fully and measure the turning angle.
| Inside wheel | Outside wheel |
| 42°45' +/- 2° (42.75° +/- 2°) | 36°21' (36.35°) |
| Inside wheel | Outside wheel |
| 42°42' +/- 2° (42.70° +/- 2°) | 36°16' (36.27°) |
| 6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION |
![]() |
Install the camber-caster-kingpin gauge or position the vehicle on the wheel alignment tester.
Inspect the camber, caster and steering axis inclination.
| Camber Right-left error | Caster Right-left error | Steering axis inclination Right-left error |
| -0°17' +/- 45' (-0.28° +/- 0.75°) 30' (0.5°) or less | 3°09' +/- 45' (3.15° +/- 0.75°) 30' (0.5°) or less | 10°25' +/- 45' (10.42° +/- 0.75°) 30' (0.5°) or less |
| Camber Right-left error | Caster Right-left error | Steering axis inclination Right-left error |
| -0°17' +/- 45' (-0.28° +/- 0.75°) 30' (0.5°) or less | 3°00' +/- 45' (3.00° +/- 0.75°) 30' (0.5°) or less | 10°12' +/- 45' (10.20° +/- 0.75°) 30' (0.5°) or less |
| 7. ADJUST CAMBER |
Remove the front wheel.
![]() |
Remove the 2 nuts on the lower side of the shock absorber. (Procedure "B")
Clean the installation surfaces of the shock absorber and the steering knuckle.
Temporarily install the 2 nuts.
![]() |
Adjust the camber by pushing or pulling the lower side of the shock absorber in the direction in which the camber adjustment is required.
Tighten the nuts.
Install the front wheel.
Check the camber.

Perform the procedure mentioned above again. At procedure "B", replace 1 or 2 selected bolts.
| 8. FRONT WHEELS FACING STRAIGHT AHEAD (w/ VSC) |
| 9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ VSC) |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ VSC) |
| 11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION (w/ VSC) |
| 12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION (w/ VSC) |