Home › BODY › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > Power Back Door Warning Buzzer does not Sound

for Preparation Click here


DESCRIPTION

  1. The power back door system uses a warning buzzer built into the back door, which has 3 ways of sounding that are used differently according to the situations:
    1. When all the following conditions are met, the warning buzzer sounds at a cycle of 0.3 seconds:
      1. The ignition switch is turned ON.
      2. The shift lever is moved into any position except P position.
      3. The back door is open or the power back door is activated to open.
        The warning buzzer continues to sound until the back door is fully closed or the shift lever is moved into the P position.
    2. While the power back door is operating, the warning buzzer sounds at a cycle of 0.7 seconds. The warning buzzer turns off when the power back door stops. This way of sounding is set to OFF at factory (default setting) and can be customized when required.
    3. When the power back door is activated to open, the warning buzzer that notifies the start of opening of the power back door sounds at 2 cycles of 0.5 seconds. At the start of opening of the power back door, a wireless buzzer (built into the engine room) also sounds.
  2. The power back door ECU directly sends a signal to the warning buzzer.

HINT:
  1. Only item 2 can be customized (Click here).
  2. If all items occur at the same time, item 1 is prior to the others.


WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Select the ACTIVE TEST and then check that the power back door warning buzzer operates.

    HINT:
    During the ACTIVE TEST, the Techstream sends a signal to the power back door ECU to drive the warning buzzer. If the warning buzzer operates, the warning buzzer itself and the wire harness between the warning buzzer and power back ECU are considered to be functioning normally.


    OK (Power back door ECU): 
    Item
    Normal Condition
    Diagnostic Note
    PBD Clutch
    Power back door buzzer is sound
    OFF / ON
    -



OK
REPLACE POWER BACK DOOR ECU
NG


2.CHECK WIRE HARNESS (POWER BACK DOOR WARNING BUZZER WIRE HARNESS SIDE)


    B067759E05
  1. Remove the buzzer connector.



  1. Inspect the buzzer connector side voltage.


    B120077E01

    NOTICE:
    Use an oscilloscope to check the output voltages of the buzzer.


    Voltage:

    Terminal No.
    Measurement Condition
    Specified Condition
    P17-1 - Body ground
    Condition that causes buzzer to sound are met (See CIRCUIT DESCRIPTION)
    1. 10 to 14 V (a cycle of 0.3 sec. or 0.7 sec.)
    2. 10 to 14 V (2 cycles of approx. 0.5 sec.)



NG
Go to step 4
OK


3.INSPECT POWER BACK DOOR WARNING BUZZER


    B068880
  1. Check the resistance of the buzzer.

    Resistance:
    Terminal No.
    Specified Condition
    1 - 2
    Approx. 1 kΩ

    NOTICE:
    1. The circuit that causes the buzzer to sounds is built into the back door ECU, not around the buzzer.
    2. Directly applying battery voltage to the buzzer does not cause the buzzer to sound.



NG
REPLACE POWER BACK DOOR WARNING BUZZER
OK


4.CHECK WIRE HARNESS (POWER BACK DOOR WARNING BUZZER - POWER BACK DOOR ECU)


    B068453E03
  1. Disconnect the P17 buzzer and the P13 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    P17-1 - P13-2 (BZR+)
    Below 1 Ω
    P17-2 - P13-1 (BZR-)



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER BACK DOOR ECU