Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Reading the Data List displayed on the Techstream enables values, including those of the switches, sensors, and actuators, to be checked without removing any parts. Reading the Data List as the first step in troubleshooting is one method to shorten diagnostic time.

NOTICE:
In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Start the engine.

  5. Turn the tester ON.

  6. Select the following menu items: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.

    Tester Display
    Measurement Item/Range
    Normal Condition*
    Diagnostic Note
    Vehicle Speed
    Vehicle speed: Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on speedometer
    Engine Speed
    Engine speed: Min.: 0 rpm, Max.: 16383.75 rpm
    600 to 700 rpm: Idling
    -
    Calculate Load
    Load calculated by ECM: Min.: 0%, Max.: 100%
    1. 10 to 20%: Idling
    2. 10 to 20%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load: Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from MAF meter: Min.: 0 g/sec., Max.: 655.35 g/sec.
    2 to 5 g/sec.: Idling
    8 to 19 g/sec.: 2500 rpm
    If value is approximately 0.0 g/ sec.:
    1. Mass air flow meter power source circuit open
    2. VG circuit open or shorted
    If value is 160.0 g/sec. or more:
    1. E2G circuit open
    Atmosphere Pressure
    Atmospheric pressure: Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F)
    80 to 100°C (176 to 212°F): After warming up
    1. If value is -40°C (-40°F): sensor circuit open
    2. If value is 140°C (284°F): sensor circuit shorted
    Intake Air
    Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F)
    Equivalent to ambient air temperature
    1. If value is -40°C (-40°F): sensor circuit open
    2. If value is 140°C (284°F): sensor circuit shorted
    Vapor Pressure (Calculated)
    Vapor pressure: (calculated) Min.: -5.632 kPa, Max.: 715.264 kPa
    0 kPa: Fuel tank cap removed
    Pressure inside fuel tank monitored by vapor pressure sensor
    Engine Run Time
    Engine run time: Min.: 0 second, Max.: 65535 seconds
    Time after engine start
    Service data
    Initial Engine Coolant Temp
    Initial engine coolant temperature: Min.: -40°C (-40°F), Max.: 120°C (248°F)
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    Initial intake air temperature: Min.: -40°C (-40°F), Max.: 120°C (248°F)
    Close to ambient air temperature
    Service data
    Battery Voltage
    Battery voltage: Min.: 0 V, Max.: 65.535 V
    9 to 14 V: Idling
    -
    Accel Sens. No. 1 Volt %
    Absolute Accelerator Pedal Position (APP) No. 1: Min.: 0%, Max.: 100%
    10 to 22%: Accelerator pedal released
    54 to 86%: Accelerator pedal fully depressed
    -
    Accel Sens. No. 2 Volt %
    Absolute APP No. 2: Min.: 0 %, Max.: 100 %
    12 to 42%: Accelerator pedal released
    66 to 98%: Accelerator pedal fully depressed
    -
    Accel Sensor Out No. 1
    APP sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Accel Sensor Out No. 2
    APP sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Accel Sensor Out No. 1
    APP sensor No. 1 voltage: Min.: 0 V, Max.: 5 V
    0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed
    -
    Accel Sensor Out No. 2
    APP sensor No. 2 voltage: Min.: 0 V, Max.: 5 V
    1.2 to 2.0 V: Accelerator pedal released
    3.4 to 5.0 V: Accelerator pedal fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle: ON or OFF
    ON: Idling
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No. 1 (AD): Min.: 0, Max.: 4.9804 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1: Min.: 0, Max.: 124.512
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2: Min.: 0, Max.: 124.512
    -
    ETCS service data
    Throttle Sensor Volt %
    Absolute throttle position sensor: Min.: 0%, Max.: 100%
    1. 10 to 24%: Throttle fully closed
    2. 64 to 96%: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Sensor #2 Volt %
    Throttle sensor positioning #2: Min.: 0%, Max.: 100%
    -
    Calculated value based on VTA2
    ST1
    Starter signal: ON or OFF
    ON: Cranking
    -
    System Guard
    System guard: ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction: ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle: ON or OFF
    ON: Idling
    -
    Throttle Require Position
    Throttle requirement position: Min.: 0 V, Max.: 5 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    Throttle sensor positioning: Min.: 0%, Max.: 100%
    10 to 18%: Idling
    Calculated value based on VTA1
    Throttle Position No. 1
    Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Throttle Position No. 2
    Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Throttle Position No. 1
    Throttle position No. 1: Min.: 0 V, Max.: 5 V
    1. 0.5 to 1.2 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully opened
    -
    Throttle Position No. 2
    Throttle position No. 2: Min.: 0 V, Max.: 5 V
    1. 2.0 to 2.9 V: Throttle fully closed
    2. 4.6 to 5.0 V: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Position Command
    Throttle position command value: Min.: 0 V, Max.: 4.9804 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.9804 V
    2.2 to 2.6 V
    ETCS service data
    Throttle Sens Open #1 (AD)
    Throttle sensor opener position No. 1 (AD): Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle motor control permitted: ON or OFF
    ON: Idling
    Read value with ignition switch on (Do not start engine)
    Throttle Motor Current
    Throttle motor current: Min.: 0 A, Max.: 20 A
    0 to 3.0 A: Idling
    -
    Throttle Motor Duty
    Throttle motor: Min.: 0%, Max.: 100%
    0.5 to 40%: Idling
    -
    Throttle Motor Current
    Throttle motor current: Min.: 0 A, Max.: 19.92A
    0 to 3.0 A: Idling
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio: Min.: 0% , Max.: 100%
    0 to 40%: Idling
    1. When accelerator pedal is depressed, duty ratio increased
    2. Read value with ignition switch ON (Do not start engine)
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio: Min.: 0% , Max.: 100%
    0 to 40%: Idling
    1. When accelerator pedal is increased quickly, duty ratio increased
    2. Read value with ignition switch ON (Do not start engine)
    Throttle Motor Duty (Open)
    Throttle motor duty ratio (open): Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle motor duty ratio (close): Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value): Min.: 0 V, Max.: 5 V
    0.4 to 0.8 V
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power input: ON or OFF
    ON: Idling
    -
    +BM Voltage
    +BM voltage: Min.: 0, Max.: 19.92182
    10 to 15 V: Idling
    ETCS service data
    Actuator Power Supply
    Actuator power supply: ON or OFF
    ON: Idling
    ETCS service data
    Clutch Current
    Clutch current: Min.: 0 A, Max.: 2.49 A
    -
    -
    Fail Safe Drive
    Whether or not fail safe function executed: ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail safe function executed (Main CPU): ON or OFF
    ON: ETCS has failed
    -
    Injector (Port)
    Injection period of No. 1 cylinder: Min.: 0 ms, Max.: 32.64 ms
    1.2 to 2.4 ms: Idling
    -
    Injection Volume (Cylinder 1)
    Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.048 ml
    Max.: 0.5 ml
    Quantity of fuel injected in 10 injections
    Fuel Pump Speed Control
    Fuel pump speed control status:
    ON or OFF
    -
    Active Test support status
    Fuel Pump / Speed Status
    Fuel pump/status: ON or OFF
    -
    Active Test support data
    Vacuum Pump
    Key-off EVAP system pump status: ON or OFF
    -
    Active Test support data
    EVAP (Purge) VSV
    EVAP (Purge) VSV control duty: Min.: 0%, Max.: 100%
    0 to 100%: Idling
    Commanded signal from ECM
    EVAP Purge Flow
    EVAP purge flow
    -
    -
    Purge Density Learn Value
    Learning value of purge density: Min.: -50, Max.: 350
    -40 to 0%: Idling
    Service data
    Vapor Pressure Pump
    Vapor pressure: Min.: 33.853 kPa, Max.: 125.596 kPa
    0 kPa: Fuel tank cap removed
    Pressure inside fuel tank monitored by vapor pressure sensor
    Tank Bypass VSV *1
    Tank bypass VSV: ON or OFF
    -
    ON: Open
    OFF: Close
    Canister control VSV *1
    Canister control VSV ON or OFF
    -
    ON: Open
    OFF: Close
    EVAP Purge VSV
    VSV status for EVAP control: ON or OFF
    -
    Active Test support data
    Target Air-Fuel Ratio
    Air-fuel ratio: Min.: 0, Max.: 1.999
    0.8 to 1.2: Idling
    -
    AF Lambda B1 S1
    Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air-fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2 S1
    Short-term fuel trim associated with bank 2 sensor 1: Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air-fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1 S1
    A/F sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of ACTIVE TEST enables technician to check voltage output of sensor
    AFS Voltage B2 S1
    A/F sensor output voltage for bank 2 sensor 1: Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of ACTIVE TEST enables technician to check voltage output of sensor
    AFS Current B1 S1
    A/F sensor current:
    Min.: -128 mA, Max.: 127.99 mA
    -
    -
    AFS Current B2 S1
    A/F sensor current:
    Min.: -128 mA, Max.: 127.99 mA
    -
    -
    O2S B1 S2
    Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V: Driving 44 mph (70 km/h)
    Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of ACTIVE TEST enables technician to check voltage output of sensor
    O2S B2 S2
    Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V: Driving 44 mph (70 km/h)
    Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of ACTIVE TEST enables technician to check voltage output of sensor
    O2S Impedance B1 S2
    Sub heated oxygen sensor impedance (bank 1 sensor 2):
    Min.: 0 Ω, Max.: 21247.68 Ω
    -
    -
    O2S Impedance B2 S2
    Sub heated oxygen sensor impedance (bank 2 sensor 2):
    Min.: 0 Ω, Max.: 21247.68 Ω
    -
    -
    Short FT #1
    Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
    Total FT #1
    Total fuel trim of bank 1
    Average value for fuel trim system of bank 1: Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Short FT #2
    Short-term fuel trim of bank 2: Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #2
    Long-term fuel trim of bank 2: Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
    Total FT #2
    Total fuel trim of bank 2
    Average value for fuel trim system of bank 2: Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (Bank 1): OL or CL or OLDRIVE or OLFAULT or CLFAULT
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to become a closed loop
    2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
    3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    4. OL FAULT: Open loop due to detected system fault
    5. CL FAULT: Closed loop but air fuel ratio sensor, used for fuel control, malfunctions
    Fuel System Status #2
    Fuel system status (Bank 2): OL or CL or OLDRIVE or OLFAULT or CLFAULT
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
    3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    4. OL FAULT: Open loop due to detected system fault
    5. CL FAULT: Closed loop but air fuel ratio sensor, used for fuel control, malfunctions
    IGN Advance
    Ignition timing advance for No. 1 cylinder: Min.: -64 deg., Max.: 63.5 deg.
    BTDC 7 to 24°: Idling
    -
    Knock Feedback Value
    Feedback value of knocking: Min.: -64 °CA, Max.: 1984 °CA
    -22 to 0° CA Driving, 44 mph (70 km/h)
    Service data
    Knock Correct Learn Value
    Correction learning value of knocking: Min.: -64 °CA, Max.: 1984 °CA
    0 to 22° CA: Driving, 44 mph (70 km/h)
    Service data
    ACIS VSV
    VSV for Acoustic Control Induction System Status: ON or OFF
    -
    ON: Open
    OFF: Close
    AICV
    AICV: ON or OFF
    -
    -
    VVT Control Status #1
    VVT control (bank 1) status: ON or OFF
    -
    Active Test support data
    VVT Control Status #2
    VVT control (bank 2) status: ON or OFF
    -
    Active Test support data
    VVT Aim Angle #1
    VVT aim angle (bank 1 Intake side): Min.: 0%, Max.: 100%
    -
    VVT duty signal value during intrusive operation
    VVT Change Angle #1
    VVT change angle (bank 1 Intake side): Min.: 0° FR, Max.: 60° FR
    0 to 5° FR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #1
    VVT OCV (bank 1 Intake side) operation duty: Min.: 0%, Max.: 100%
    0 to 100%
    Requested duty value for intrusive operation
    VVT Aim Angle #2
    VVT aim angle (bank 2 Intake side): Min.: 0%, Max.: 100%
    -
    VVT duty signal value during intrusive operation
    VVT Change Angle #2
    VVT change angle (bank 2 Intake side): Min.: 0° FR, Max.: 60° FR
    0 to 5° FR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #2
    VVT OCV (bank 2 Intake side) operation duty: Min.: 0%, Max.: 100%
    0 to 100%:
    Requested duty value for intrusive operation
    VVT Ex Hold Lrn Val #1
    VVT exhaust hold duty ratio learning value (bank 1 Exhaust side): Min.: 0%, Max.: 100%
    0 to 50%: Idling
    Requested duty value for intrusive operation
    VVT Ex Chg Angle #1
    VVT change angle (bank 1 Exhaust side): Min.: 0° FR, Max.: 60° FR
    0 to 5° FR: Idling
    Displacement angle during intrusive operation
    VVT Ex OCV Duty #1
    VVT OCV (bank 1 Exhaust side) operation duty: Min.: 0%, Max.: 100%
    0 to 100%
    Requested duty value for intrusive operation
    VVT Ex Hold Lrn Val #2
    VVT exhaust hold duty ratio learning value (bank 2 Exhaust side): Min.: 0%, Max.: 100%
    10 to 50%: Idling
    Requested duty value for intrusive operation
    VVT Ex Chg Angle #2
    VVT change angle (bank 2 Exhaust side): Min.: 0° FR, Max.: 60° FR
    0 to 5° FR: Idling
    Displacement angle during intrusive operation
    VVT Ex OCV Duty #2
    VVT exhaust (bank 2 Exhaust side) operation duty: Min.: 0%, Max.: 100%
    0 to 100%
    Requested duty value for intrusive operation
    Catalyst Temp B1 S1
    Catalyst temperature (Bank 1, Sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Catalyst Temp B2 S1
    Catalyst temperature (Bank 2, Sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Catalyst Temp B1 S2
    Catalyst temperature (Bank 1, Sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Catalyst Temp B2 S2
    Catalyst temperature (Bank 2, Sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    -
    -
    Starter Signal
    Starter signal: ON or OFF
    ON: Cranking
    -
    Starter Control
    Starter switch signal: ON or OFF
    -
    -
    Power Steering Signal Record
    Power steering signal: ON or OFF
    ON: Power steering operation
    -
    Starter Relay
    Starter relay: ON or OFF
    ON: Cranking
    -
    Power Steer. Sig. Record
    Power steering signal: ON or OFF
    ON: Steering wheel is first turned after ignition switch is turned on
    This signal status is usually ON until ignition switch is turned off
    ACC Relay
    ACC Relay: ON or OFF
    ON: Cranking
    -
    Neutral Position SW Signal
    PNP switch status: ON or OFF
    ON: P or N position
    -
    Stop Light Switch
    Stop light switch: ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C signal: ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch: ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Electrical Load Signal
    Electrical load signal: ON or OFF
    ON: Headlights or defogger turned ON
    -
    Check Mode
    Check mode: 0: OFF, 1: ON
    ON: Check mode ON
    Click here
    SPD Test Result
    Check mode result for vehicle speed sensor: 0: Compl, 1: Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor: 0: Compl, 1: Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for HO2 sensor (bank 1): 0: Compl, 1: Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for HO2 sensor (bank 2): 0: Compl, 1: Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air-fuel ratio sensor (bank 2): 0: Compl, 1: Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air-fuel ratio sensor (bank 1): 0: Compl, 1: Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive Component Monitor: Not Avl / Avail
    -
    -
    Fuel System Monitor
    Fuel System Monitor: Not Avl / Avail
    -
    -
    Misfire Monitor
    Misfire Monitor: Not Avl / Avail
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater Monitor: Not Avl / Avail
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater Monitor: Compl / Incmpl
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) Monitor: Not Avl / Avail
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) Monitor: Compl / Incmpl
    -
    -
    EVAP Monitor
    EVAP Monitor: Not Avl: Avail
    -
    -
    EVAP Monitor
    EVAP Monitor: Compl / Incmpl
    -
    -
    Catalyst Monitor
    Catalyst Monitor: Not Avl / Avail
    -
    -
    Catalyst Monitor
    Catalyst Monitor: Compl / Incmpl
    -
    -
    Component Monitor ENA
    Component Monitor: Unable or Enable
    -
    -
    Component Monitor CMPL
    Component Monitor Compl: Complete or Incomplete
    -
    -
    Fuel System Monitor ENA
    Fuel System Monitor: Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel System Monitor Compl: Complete or Incomplete
    -
    -
    Misfire Monitor ENA
    Misfire Monitor: Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire Monitor Compl: Complete or Incomplete
    -
    -
    EGR/VVT Monitor ENA
    O2S (A/FS) heater Monitor: Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR Monitor: Unable or Enable
    -
    -
    Heater Monitor ENA
    Heater Monitor Compl: Complete or Incomplete
    -
    -
    Heater Monitor CMPL
    Heater Monitor Compl: Complete or Incomplete
    -
    -
    O2S (A/FS) Monitor ENA
    O2S (A/FS) Monitor: Unable or Enable
    -
    -
    O2S (A/FS) Monitor CMPL
    O2S (A/FS) Monitor Compl: Complete or Incomplete
    -
    -
    A/C Monitor ENA
    A/C Monitor: Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C Monitor Compl: Complete or Incomplete
    -
    -
    2nd Air Monitor ENA
    2nd Air Monitor: Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd Air Monitor Compl: Complete or Incomplete
    -
    -
    EVAP Monitor ENA
    EVAP Monitor: Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP Monitor Compl: Complete or Incomplete
    -
    -
    Heater Cat Monitor ENA
    Heater Cat Monitor: Unable or Enable
    -
    -
    Heater Cat Monitor CMPL
    Heater Cat Monitor Compl: Complete or Incomplete
    -
    -
    Catalyst Monitor ENA
    Catalyst Monitor: Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst Monitor Compl: Complete or Incomplete
    -
    -
    #Codes (Include History)
    #Codes: Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status: ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    MIL ON Run Distance: Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
    Distance driven after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON: Min.: 0 minute, Max.: 65535 minutes
    Running time after MIL ON
    -
    Time after DTC Cleared
    Time after DTC cleared: Min.: 0 minute, Max.: 65535 minutes
    Time after DTCs erased
    -
    Distance from DTC Cleared
    Distance after DTC cleared: Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
    Distance driven after DTCs erased
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared: Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    OBD Requirements
    OBD Requirement:
    OBD2 (CARB)
    -
    Number of Emission DTC
    Number of Emission related DTC
    -
    -
    TC and TE1
    TC and TE1 terminals of DLC3: ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter: Min.: 0, Max.: 600
    0 to 600
    -
    Cylinder #1 Misfire Count
    Misfire ratio of cylinder 1: Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #2 Misfire Count
    Misfire ratio of cylinder 2: Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #3 Misfire Count
    Misfire ratio of cylinder 3: Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #4 Misfire Count
    Misfire ratio of cylinder 4: Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #5 Misfire Count
    Misfire ratio of cylinder 5: Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #6 Misfire Count
    Misfire ratio of cylinder 6: Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    All Cylinders Misfire Count
    All cylinders misfire rate: Min.: 0, Max.: 255
    0 to 35
    -
    Misfire RPM
    Engine RPM for first misfire range: Min.: 0 rpm, Max.: 6,375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring: Min.: -100%, Max.: 99.22%
    -100 to 99.2%
    Misfire detecting margin
    Catalyst OT MF F/C
    Catalyst overheat misfire prevention fuel cut availability:
    Not Avl or Avail
    Avail: Catalyst OT MF F/C available
    Not Avl: Catalyst OT MF F/C not available
    Service data
    Cat OT MF F/C History
    Catalyst overheat misfire prevention fuel cut history:
    ON or OFF
    ON: Fuel cut operation history exists
    Service data
    Cat OT MF F/C Cylinder#1
    Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected): ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder#2
    Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected): ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder#3
    Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected): ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder#4
    Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected): ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder#5
    Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected): ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder#6
    Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected): ON or OFF
    ON: Fuel cut is operating
    -
    ACM
    VSV for ACM duty control:
    Min.: 0%, Max.: 255%
    -
    Active Test support data
    Electric Fan Motor
    Electric fan motor: ON or OFF
    -
    Active Test support data
    Idle Fuel Cut
    Fuel cut idle: ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut = ON when throttle valve is fully closed and engine speed is over 2800 rpm
    FC TAU
    Fuel cut TAU: Fuel cut with very light load: ON or OFF
    ON: Fuel cut operation
    Fuel cut being performed with very light load to prevent incomplete engine combustion
    Model Code
    Model code information
    -
    Identifying model code: GSL2#
    Engine Type
    Engine type information
    -
    Identifying engine type: 2GRFE
    Cylinder Number
    Cylinder number: Min.: 0, Max.: 255
    -
    Identifying cylinder number: 6
    Destination
    Destination
    -
    Identifying destination: A (America)
    Model Year
    Model year: Min.: 1900 MY, Max.: 2155 MY
    -
    Identifying model year: 200#
    System Identification
    System Identification
    -
    Identifying engine system: gasoline engine
    Normal condition: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.
    *1: Only for Mexico Models.


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with the Techstream. Performing an Active Test in the first step in troubleshooting is one method to shorten diagnostic time.
Data List can be displayed during Active Test.

  1. Connect the Techstream to the DLC3.

  2. Start the engine.

  3. Turn the tester ON.

  4. Select the following menu items: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Test by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change the injection volume
    Between -12.5% and 24.8%
    1. All injectors tested at the same time
    2. Perform test at less than 3000 rpm
    3. Injection volume can be changed by 1% within control range
    Control the Injection Volume A/F Sensor
    Change the injection volume
    Lower by 12.5% or increase by 24.8%
    1. Perform test at less than 3000 rpm
    2. Control the Injection Volume for A/F sensor Operation enables to check and to graph A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs
    3. To conduct test, select following menu items: Active Test / Control the Injection volume for A/F sensor / A/F Control System / AFS B1S1 or AFS B2S1 and O2S B1S2 or O2S B2S2 then press the graph button on the Data List view.
    Activate the Fuel Pump Speed Control
    Fuel pump speed control
    ON (low speed) / OFF (high speed)
    Test possible when following conditions met:
    Ignition switch ON
    Engine is stopped
    Activate the VSV for Intake Control
    Activate the VSV for Acoustic Control Induction System (ACIS)
    ON / OFF
    -
    Activate the VSV for Evap Control
    Activate EVAP VSV control
    ON / OFF
    -
    Control the Fuel Pump / Speed
    Activate fuel pump (C/OPN Relay)
    ON / OFF
    -
    Control the ACM Inhibit
    Control the ACM inhibit
    ON / OFF
    Test is possible while engine is idling
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON / OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON / OFF
    -
    Prohibit the Catalyst OT Misfire prevent F/C
    Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
    ON: Fuel cut is prohibited
    Confirm that the vehicle is stopped and engine speed is 3000 rpm or less.
    Control the Electric Cooling Fan
    Control the electric cooling fan
    ON / OFF
    -
    Activate the Starter Relay
    Starter
    ON / OFF
    -
    Activate the ACC Cut Relay
    Active ACC cut relay
    ON / OFF
    Test is possible when following conditions are met:
    1. Ignition switch is ON position
    2. Ignition is stopped
    Control the ETCS Open Slow Speed
    Control the ETCS (throttle motor) opening slow speed
    1: Throttle valve opens slowly
    Test is possible when the following conditions are met:
    1. Ignition switch on
    2. Engine does not start
    3. Accelerator pedal fully depressed (APP: 58 degrees or more)
    Control the ETCS Close Slow Speed
    Control the ETCS (throttle motor) closing slow speed
    2: Throttle valve closes slowly
    Same as above
    Control the ETCS Open Fast Speed
    Control the ETCS (throttle motor) opening fast speed
    3: Throttle valve opens fast
    Same as above
    Control the ETCS Close Fast Speed
    Control the ETCS (throttle motor) closing fast speed
    4: Throttle valve closes fast
    Same as above
    Control the VVT Linear (Bank 1)
    Control the VVT (bank 1 Intake Side)
    Between -128 and 127%
    This valve added to present OCV control duty
    100%: Maximum retard
    -100% : Maximum advance
    Engine stalls or idles roughly when VVT actuator operated by 100%. Test is possible while idling.
    Control the VVT System (Bank 1)
    Turn on and off OCV (Oil Control Valve) for VVT (Bank 1)
    ON: Exhaust side camshaft moves to retard side
    OFF: Exhaust side camshaft moves to advance side
    1. Engine stalls or idles roughly when OCV on
    2. Engine running or idling normally when OCV off
    Control the VVT Linear (Bank 2)
    Control the VVT (bank 2 Intake Side)
    Between -128% and 127%
    Same as above
    Control the VVT System (Bank 2)
    Turn on and off OCV (Oil Control Valve) for VVT (Bank 2)
    ON: Exhaust side camshaft moves to retard side
    OFF: Exhaust side camshaft moves to advance side
    1. Engine stalls or idles roughly when OCV on
    2. Engine running or idling normally when OCV off
    Control the VVT Exhaust Linear (Bank 1)
    Control the VVT (bank 1 Exhaust Side)
    This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    Same as above
    Control the VVT Exhaust Linear (Bank 2)
    Control the VVT (bank 2 Exhaust Side)
    Same as above
    Same as above
    Activate the Vacuum Pump
    Activate the Vacuum Pump built into pump module
    ON / OFF
    -
    Activate the VSV for Vent Valve
    Activate the VSV for Vent Valve built into pump module
    ON / OFF
    -
    Activate the VSV for AICS
    Activate the VSV for Air Intake Control System (AICS)
    ON / OFF
    -
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON / OFF
    Test possible while vehicle stopped and engine idling*1
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON / OFF
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON / OFF
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON / OFF
    Control the Cylinder #5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON / OFF
    Control the Cylinder #6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON / OFF

    NOTICE:
    *1: If the display of the Data List's Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling. If the display of the Data List's Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
    1. Stop the engine and turn the ignition switch to the ON position to turn Control the Cylinder #1 Fuel Cut (to #6 Fuel Cut) ON.
    2. Start the engine.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of the multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.

  1. Connect the Techstream to the DLC3.

  2. Start the engine.

  3. Turn the tester ON.

  4. Select the following menu items: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Notes
    Evaporative System Check
    (Automatic Mode)
    Perform 5 steps in order to operate EVAP key-off monitor automatically
    35°C (95°F) or less
    1. If no DTCs in Pending after performing this test, system functioning normally.
    2. Refer to EVAP System (Click here)
    Evaporative System Check
    (Manual Mode)
    Perform 5 steps in order to operate EVAP key-off monitor manually
    35°C (95°F) or less
    1. Used to detect malfunctioning parts.
    2. Refer to EVAP System (Click here)