DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
DTC P0430 Catalyst System Efficiency Below Threshold (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | Oxygen Storage Capacity (OSC) value is smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|
| P0430 | OSC value is smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|
| Related DTCs | P0420: Catalyst Deterioration P0430: Catalyst Deterioration |
| Required Sensors / Components (Main) | TWC |
| Required Sensors / Components (Related) | A/F sensor, heated oxygen sensor, intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Approximately 30 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0010, P0020 (OCV bank 1, 2) P0011, P0021 (VVT system bank 1, 2 - advance) P0012, P0022 (VVT system bank 1, 2 - retard) P0013, P0023 (Exhaust OCV bank 1, 2) P0014, P0024 (Exhaust VVT system bank 1, 2 - advance) P0015, P0025 (Exhaust VVT system bank 1, 2 - retard) P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052 (A/F sensor heater) P0037, P0038, P0057, P0058 (HO2 sensor heater) P0100, P0102, P0103 (MAF meter) P0115, P0117, P0118 (ECT sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0136, P0137, P0138 (HO2 sensor bank 1) P0156, P0157, P0158 (HO2 sensor bank 2) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (CKP sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0606 (HO2 sensor - sensor 2) P2195, P2196, P2197, P2198 (A/F sensor - rationality) P2237, P2240 (A/F sensor - open) P2238, P2241, P2252, P2255 (A/F sensor - low impedance) P2239, P2242, P2253, P2256 (A/F sensor - high impedance) P2A00, P2A03 (A/F sensor - slow response) |
| Battery voltage | 11 V or more |
| IAT | -10°C (14°F) or more |
| ECT | 75°C (167°F) or more |
| Atmospheric pressure | 0.75 or more |
| Idle | OFF |
| Engine RPM | Less than 3200 rpm |
| A/F sensor | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 70% |
| All of the following conditions are met | Conditions 1, 2 and 3 |
| 1. Mass air flow rate | 5 to 60 g/sec. |
| 2. Front catalyst temperature (estimated) | 600 to 800°C (1112 to 1472°F) |
| 3. Rear catalyst temperature (estimated) | 100 to 900°C (212 to 1652°F) |
| EVAP system monitor | The monitor has not run yet or the vacuum introduction has been completed |
| A/F sensor monitor | Completed |
| Rear HO2S monitor | Completed |
| Shift position | 4th or more |
| Oxygen Storage Capacity (OSC) of catalyst | Less than 0.046 g (0.000101 lb) |


| A/F CONTROL |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.1 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.5 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0420 and/or P0430 | A |
| P0420 and/or P0430 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.1 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.5 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Status AFS B1S1 or AFS B2S1 | Status O2S B1S2 or O2S B2S2 | A/F Condition and A/F and HO2 Sensor Conditions | Misfires | Suspected Trouble Areas | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
| Rich | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
| Lean/Rich | Lean | HO2 sensor malfunction | - |
| C |
| Lean/Rich | Rich | HO2 sensor malfunction | - |
| C |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| A |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0420 | A |
| P0430 | B |
| P0420 and P0430 | A and B |
|
| ||||
| A | |
| 5.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH |
Replace exhaust manifold sub-assembly RH .
| NEXT | ||
| ||
| 6.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
Replace exhaust manifold sub-assembly LH .
| NEXT | ||
| ||