Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0441    Evaporative Emission Control System Incorrect Purge Flow

for Preparation Click here


DTC SUMMARY


DTCs
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0441
Purge VSV (Vacuum Switching Valve) stuck open
Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. 0.02 inch leak pressure standard is measured at start and end of leak check.
If stabilized pressure is higher than [second 0.02 inch leak pressure standard x 0.2], ECM determines that purge VSV is stuck open
  1. Purge VSV
  2. Purge VSV circuit (between purge VSV and ECM)
  3. Leakage from EVAP line (between purge VSV and intake manifold)
  4. EVAP line clogged (between purge VSV and canister)
  5. ECM
While ignition switch OFF
2 trip
P0441
Purge VSV stuck closed
After EVAP leak check is performed, purge VSV is turned ON (open), and atmospheric air is introduced into EVAP system. 0.02 inch leak pressure standard is measured at the start and end of leak check.
If pressure does not return to near atmospheric pressure, ECM determines that purge valve is stuck closed
While ignition switch OFF
2 trip
P0441
Purge flow
While engine running, the following conditions are successively met:
  1. Negative pressure is not created in EVAP system when purge VSV is turned ON (open)
  2. EVAP system pressure change is less than 0.5 kPa (3.75 mmHg) when vent valve is turned ON (closed)
  3. Atmospheric pressure change before and after purge flow monitor is less than 0.1 kPa (0.75 mmHg)
While ignition switch OFF
2 trip

DESCRIPTION

The circuit description can be found in the EVAP (Evaporative Emission) System .

INSPECTION PROCEDURE

Refer to the EVAP System .

MONITOR DESCRIPTION

The two monitors, Key-Off and Purge Flow, are used to detect malfunctions relating to DTC P0441. The Key-off monitor is initiated by the ECM internal timer, known as the soak timer, 5 hours*1 after the ignition switch is turned off. The purge flow monitor runs while the engine is running.

KEY-OFF MONITOR
5 hours*1 after the ignition switch is turned off, the electric leak detection pump creates negative pressure (vacuum) in the EVAP (Evaporative Emission) system. The ECM monitors for leaks and actuator malfunctions based on the EVAP pressure.

HINT:
*1: If the engine coolant temperature is not below 35°C (95°F) 5 hours after the ignition switch is turned off, the monitor check starts 2 hours later. If it is still not below 35°C (95°F) 7 hours after the ignition switch is turned off, the monitor check starts 2.5 hours later.

Sequence
Operation
Description
Duration
-
ECM activation
Activated by soak timer, 5 hours (7 or 9.5 hours) after ignition switch turned off.
-
A
Atmospheric pressure measurement
Vent valve is turned OFF (vent) and EVAP system pressure is measured by ECM in order to register atmospheric pressure.
If pressure in EVAP system is not between 70 kPa and 110 kPa (525 mmHg and 825 mmHg), ECM cancels EVAP system monitor.
10 seconds
B
First 0.02 inch leak pressure measurement
In order to determine 0.02 inch leak pressure standard, leak detection pump creates negative pressure (vacuum) through 0.02 inch orifice and then ECM checks if leak detection pump and vent valve operate normally.
60 seconds
C
EVAP system pressure measurement
Vent valve is turned ON (closed) to shut EVAP system.
Negative pressure (vacuum) is created in EVAP system, and EVAP system pressure is then measured.
Write down measured value as it will be used in leak check.
If EVAP pressure does not stabilize within 15 minutes, ECM cancels EVAP system monitor.
15 minutes*2
D
Purge VSV monitor
Purge VSV is opened and then EVAP system pressure is measured by ECM.
Large increase indicates normal.
10 seconds
E
Second 0.02 inch leak pressure measurement
After second 0.02 inch leak pressure measurement, leak check is performed by comparing first and second 0.02 inch leak pressure standards.
If stabilized system pressure is higher than second 0.02 inch leak pressure standard, ECM determines that EVAP system leaking.
60 seconds
F
Final check
Atmospheric pressure is measured and then monitoring result is recorded by ECM.
-
*2: If only a small amount of fuel is in the fuel tank, it takes longer for the EVAP pressure to stabilize.


A096746E38



  1. Purge VSV stuck open
    In operation C, the leak detection pump creates negative pressure (vacuum) in the EVAP (Evaporative Emission) system. The EVAP system pressure is then measured by the ECM using the canister pressure sensor. If the stabilized system pressure is higher than [second 0.02 inch leak pressure standard x 0.2], the ECM interprets this as the purge VSV (Vacuum Switching Valve) being stuck open. The ECM illuminates the MIL and sets the DTC (2 trip detection logic).


    G036775E10



  2. Purge VSV stuck closed
    In operation D, the canister pressure sensor measures the EVAP (Evaporative Emission) system pressure. The pressure measurement for purge VSV monitor is begun when the purge VSV is turned on (open) after the EVAP leak check. When the measured pressure indicates an increase of 0.3 kPa (2.25 mmHg) or more, the purge VSV is functioning normally. If the pressure does not increase, the ECM interprets this as the purge VSV being stuck closed. The ECM illuminates the MIL and sets the DTC (2 trip detection logic).


    G036776E18


PURGE FLOW MONITOR
The purge flow monitor consists of the two step monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.
Atmospheric pressure check:
In order to ensure reliable malfunction detection, the variation between the atmospheric pressures, before and after conduction of the purge flow monitor, is measured by the ECM.
A071563E17
  1. The 1st monitor
    While the engine is running and the purge VSV (Vacuum Switching Valve) is on (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If negative pressure is not created, the ECM begins the 2nd monitor.
  2. The 2nd monitor
    The vent valve is turned on (closed) and the EVAP pressure is then measured. If the variation in the pressure is less than 0.5 kPa (3.75 mmHg), the ECM interprets this as the purge VSV being stuck closed, and illuminates the MIL and sets DTC P0441 (2 trip detection logic).

OBD II MONITOR SPECIFICATIONS


Key-off Monitor

Monitor Strategy 
Required Sensors/Components
Purge VSV
Canister pump module
Frequency of Operation
Once per driving cycle
Duration
Within 15 minutes (varies with fuel in tank)
MIL Operation
2 driving cycles
Sequence of Operation
None

Typical Enabling Conditions 
EVAP key-off monitor runs when all of following conditions are met
-
Atmospheric pressure
70 to 110 kPa (525 to 825 mmHg)
Battery voltage
10.5 V or more
Vehicle speed
Below 2.5 mph (4 km/h)
Ignition switch
OFF
Time after key off
5, 7 or 9.5 hours
Canister pressure sensor malfunction (P0450, P0452 and P0453)
Not detected
Purge VSV
Not operated by scan tool
Vent valve
Not operated by scan tool
EVAP leak detection pump
Not operated by scan tool
Both of following conditions are met before key off
Conditions 1 and 2
1. Duration that vehicle driven
5 minutes or more
2. EVAP purge operation
Performed
Engine coolant temperature
4.4 to 35°C (40 to 95°F)
Intake air temperature
4.4 to 35°C (40 to 95°F)

Typical Malfunction Thresholds 
Purge VSV stuck open:
-
EVAP pressure when vacuum introduction complete
Higher than reference pressure x 0.2

Purge VSV stuck closed:
-
EVAP pressure change after purge VSV ON (open)
Less than 0.3 kPa (2.25 mmHg)

OBD II MONITOR SPECIFICATIONS


Purge Flow Monitor

Monitor Strategy 
Required Sensors/Components
Purge VSV
Canister pump module
Frequency of Operation
Once per driving cycle
Duration
Within 10 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

Typical Enabling Conditions 
Monitor runs whenever following DTCs are not present
None
Engine
Running
Engine coolant temperature
4.4°C (40°F) or more
Intake air temperature
4.4°C (40°F) or more
Canister pressure sensor malfunction
Not detected
Purge VSV
Not operated by scan tool
EVAP system check
Not operated by scan tool
Battery voltage
10 V or more
Purge duty cycle
8% or more

Typical Malfunction Thresholds 
Both of following conditions are met
Conditions 1 and 2
1. EVAP pressure change when purge operation started
Less than 0.1 kPa (0.75 mmHg)
2. EVAP pressure change during purge flow when EVAP pressure closed
Less than 0.5 kPa (3.8 mmHg)

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).