DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | Deviations in crankshaft and camshaft position sensor (for intake camshaft) 1 signals (2 trip detection logic) |
|
| P0018 | Deviations in crankshaft and camshaft position sensor (for intake camshaft) 2 signals (2 trip detection logic) |
| Related DTCs | P0016: Deviation in crankshaft position sensor signal and camshaft position sensor signal (Bank 1) P0018: Deviation in crankshaft position sensor signal and camshaft position sensor signal (Bank 2) |
| Required Sensors / Components (Main) | P0016 and P0018: VVT actuator |
| Required Sensors / Components (Related) | P0016 and P0018: Camshaft position sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Less than 60 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0010, P0020 (OCV bank 1, 2) P0100, P0102, P0103 (MAF meter) P0115, P0117, P0118 (ECT sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) |
| Engine RPM | 500 to 1000 rpm |
| One of the following conditions is met: | Condition 1 or 2 |
| 1. VVT learning value at maximum retarded valve timing | Less than 18.5° CA |
| 2. VVT learning value at maximum retarded valve timing | More than 43.5° CA |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0016 AND P0018) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0016 or P0018 | A |
| P0016 or P0018 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OIL CONTROL VALVE FOR INTAKE CAMSHAFT) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine idle speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Select the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read the DTCs using the tester.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND A JUMPED TOOTH OF TIMING CHAIN) |
![]() |
Remove the cylinder head covers RH and LH.
Turn the crankshaft to align the matchmarks of the crankshaft.
Align the notch of the crankshaft pulley to the "0" position.
Check if the matchmarks of the camshaft pulley and camshaft bearing cap align.
Turn the crankshaft clockwise by 360° if the matchmarks do not align. Check if they align once again.
Confirm that the DTC output does not recur.
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Clear the DTCs (Click here).
Select the check mode using the tester (Click here).
Start the engine and warm it up.
Allow the engine to idle for 1 minute or more, and then drive the vehicle for 1 minute or more.
Confirm that no DTC is set using the tester.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
Remove the camshaft timing oil control valve (OCV).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
![]() |
Apply the positive battery voltage to terminal 1 and the negative battery voltage to terminal 2. Check the valve operation.
Reinstall the OCV.
|
| ||||
| OK | |
| 6.CHECK OIL PIPE AND OIL CONTROL VALVE FILTER |
![]() |
Remove the oil pipe No. 1 or oil pipe assembly.
Remove the oil control valve filter.
Check that the filter and pipe are not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Select the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Confirm that no DTC is set using the tester.
|
| ||||
| OK | ||
| ||