Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0365    Camshaft Position Sensor "B" Circuit (Bank 1)

DTC    P0367    Camshaft Position Sensor "B" Circuit Low Input (Bank 1)

DTC    P0368    Camshaft Position Sensor "B" Circuit High Input (Bank 1)

DTC    P0390    Camshaft Position Sensor "B" Circuit (Bank 2)

DTC    P0392    Camshaft Position Sensor "B" Circuit Low Input (Bank 2)

DTC    P0393    Camshaft Position Sensor "B" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.
When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
  1. Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 4seconds, when 2 or more seconds have elapsed after turning ignition switch to the ON position
    (1 trip detection logic)
  2. Missing VVT sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or more
    (1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0367
P0392
Output voltage of VVT sensor is 0.3 V or less for 4 seconds
(1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0368
P0393
Output voltage of VVT sensor is 4.7 V or more for 4 seconds
(1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM

MONITOR DESCRIPTION

If no signal is transmitted by the VVT (for exhaust camshaft) sensor despite the engine revolving, or the rotations of the exhaust camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0365: Exhaust VVT Position sensor (Bank 1) range check / rationality
P0365: Exhaust VVT Position sensor (Bank 1) range check (chattering)
P0367: Exhaust VVT Position sensor (Bank 1) range check (low voltage)
P0368: Exhaust VVT Position sensor (Bank 1) range check (high voltage)
P0390: Exhaust VVT Position sensor (Bank 2) range check / rationality
P0390: Exhaust VVT Position sensor (Bank 2) range check (chattering)
P0392: Exhaust VVT Position sensor (Bank 2) range check (low voltage)
P0393: Exhaust VVT Position sensor (Bank 2) range check (high voltage)
Required Sensors / Components (Main)
Exhaust VVT Position sensor (Bank 1 and 2)
Required Sensors / Components (Related)
Exhaust VVT Position sensor
Frequency of Operation
Continuous
Duration
5 seconds: Exhaust camshaft sensor range check / rationality (After starting engine)
4 seconds: Others
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever these DTCs are not present
None

Exhaust VVT Position Sensor Range Check / Rationality: 
Engine RPM
600 rpm or more
Starter
OFF
Battery voltage
8 V or more
Ignition Switch
ON

Exhaust VVT Position Sensor Range Check (Chattering, Low voltage, High voltage): 
Starter
OFF
Ignition Switch ON and time after ignition switch is OFF to ON
2 seconds or more
Battery voltage
8 V or more

TYPICAL MALFUNCTION THRESHOLDS


Exhaust VVT Position Sensor Range Check / Rationality: 
Exhaust camshaft sensor signal
No signal

Exhaust VVT Position Sensor Range Check (Chattering): 
Exhaust camshaft sensor signal
Less than 0.3 V, or more than 4.7 V

Exhaust VVT Position Sensor Range Check (Low voltage): 
Exhaust camshaft sensor signal
Less than 0.3 V

Exhaust VVT Position Sensor Range Check (High voltage): 
Exhaust camshaft sensor signal
More than 4.7 V

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR POWER SOURCE)


    A107149E59
  1. Disconnect the C21 or C20 VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC2 (C20-3) - Body ground
    4.5 to 5.0 V
    VC2 (C21-3) - Body ground
    4.5 to 5.0 V



NG
Go to step 7
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)


    A165549E02
  1. Disconnect the C21 or C20 VVT sensor for exhaust camshaft connector.

  1. Disconnect the E11 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Check for open:
    Tester Connection
    Specified Condition
    EX+ (C21-1) - EV1+ (E11-25)
    Below 1 Ω
    EX- (C21-2) - EV1- (E11-24)
    Below 1 Ω
    EX+ (C20-1) - EV2+ (E11-23)
    Below 1 Ω
    EX- (C20-2) - EV2- (E11-22)
    Below 1 Ω
    Check for short:
    Tester Connection
    Specified Condition
    EX+ (C21-1) - EV1+ (E11-25) - Body ground
    10 kΩ or higher
    EX- (C21-2) - EV1- (E11-24) - Body ground
    10 kΩ or higher
    EX+ (C20-1) - EV2+ (E11-23) - Body ground
    10 kΩ or higher
    EX- (C20-2) - EV2- (E11-22) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR - ECM)
OK


3.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR INSTALLATION)


    BR03795E18
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE VVT SENSOR
OK


4.CHECK EXHAUST CAMSHAFT
  1. Check the teeth of the camshaft.



NG
REPLACE EXHAUST CAMSHAFT
OK


5.REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT)
  1. Replace the VVT sensor (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the Techstream on.

  1. Clear the DTCs.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P0365, P0352, P0353, P0354, P0355 or P0356
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

7.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)


    A165583E02
  1. Disconnect the C21 or C20 VVT sensor connector.

  1. Disconnect the E9 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Check for open:
    Tester Connection
    Specified Condition
    VC2 (C20-3) - VC (E9-23)
    Below 1 Ω
    VC2 (C21-3) - VC (E9-23)
    Below 1 Ω
    Check for short:
    Tester Connection
    Specified Condition
    VC2 (C20-3) or VC (E9-23) - Body ground
    10 kΩ or higher
    VC2 (C21-3) or VC (E9-23) - Body ground
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR - ECM)
OK

REPLACE ECM (Click here)