DTC P0504 Brake Switch "A" / "B" Correlation |
DTC P0724 Brake Switch "B" Circuit High |
| Signals | Brake Pedal Released | In Transition | Brake Pedal Depressed |
| STP | OFF | ON | ON |
| ST1- | ON | ON | OFF |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0504 | Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch in the ON position (b) Brake pedal released (c) STP signal OFF when ST1- signal OFF |
|
| P0724 | The stop light switch remains ON even when the vehicle is driven in a STOP (less than 2 mph (3 km/h)) and GO (19 mph (30 km/h) or more) fashion 5 times. (2 trip detection logic) |
|
| Related DTCs | P0724: Stop light switch/Rationality |
| Required sensors/Components | Stop light switch, Vehicle speed sensor |
| Frequency of operation | Continuous |
| Duration | GO and STOP 5 times |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present | None |
| Ignition switch | ON |
| Starter | OFF |
| Battery voltage | 8 V or more |
| GO (Vehicle speed is 18.65 mph (30 km/h) or more) | Once |
| STOP (Vehicle speed is less than 1.86 mph (3 km/h)) | Once |
| Switch status ON stuck | Remain ON during GO and STOP 5 times |

| 1.CHECK OPERATION OF STOP LIGHT |
Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.
|
| ||||
| OK | |
| 2.INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() |
Remove the S12 stop light switch assembly.
Measure the resistance according to the value(s) in the table below.
| Switch Position | Tester Connection | Specified Condition |
| Switch pin free | 1 - 2 | Below 1 Ω |
| Switch pin free | 3 - 4 | 10 kΩ or higher |
| Switch pin pushed in | 1 - 2 | 10 kΩ or higher |
| Switch pin pushed in | 3 - 4 | Below 1 Ω |
Reinstall the stop light switch assembly.
|
| ||||
| OK | |
| 3.READ VALUE USING TECHSTREAM (STP SIGNAL AND ST1 - VOLTAGE) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
Check the STP signal when the brake pedal is depressed and released.
| Brake Pedal Operation | Specified Condition |
| Depressed | STP signal ON |
| Released | STP signal OFF |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Operation | Specified Condition |
| ST1- (E4-16) - E1 (E11-1) | Depressed | Below 1.5 V |
| ST1- (E4-16) - E1 (E11-1) | Released | 7.5 to 14 V |
|
| ||||
| NG | |
| 4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM) |
![]() |
Disconnect the S12 stop light switch connector.
Disconnect the E4 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| Stop light switch (S12-1) - STP (E4-15) | Below 1 Ω |
| Stop light switch (S12-4) - ST1- (E4-16) | Below 1 Ω |
| Tester Connection | Specified Condition |
| Stop light switch (S12-1) or STP (E4-15) - Body ground | 10 kΩ or higher |
| Stop light switch (S12-4) or ST1- (E4-16) - Body ground | 10 kΩ or higher |
Reconnect the stop light switch connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||