DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic) |
|
| P2123 | VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more (b) VPA is between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 is 0.02 V or less (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less |
|
| Trouble Areas | Accelerator Position No. 1 When AP Released | Accelerator Position No. 2 When AP Released | Position No. 1 When AP Depressed | Position No. 2 When AP Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.0 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 5.0 V |
| Related DTCs | P2120: Accelerator Pedal Position (APP) sensor 1 range check (fluctuating) P2122: APP sensor 1 range check (low voltage) P2123: APP sensor 1 range check (high voltage) P2125: APP sensor 2 range check (fluctuating) P2127: APP sensor 2 range check (low voltage) P2128: APP sensor 2 range check (high voltage) P2138: APP sensor range check (correlation) |
| Required Sensors / Components (Main) | APP sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P2120, P2122, P2125 and P2127 2.0 seconds: P2123, P2128 and P2138 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Throttle actuator power | ON |
| Either of the following conditions is met | Condition A or B |
| A. VPA voltage when VPA2 is 0.04 V or more | 0.4 V or less |
| B. VPA voltage | 4.8 V or more |
| VPA voltage when VPA2 is 0.04 V or more | 0.4 V or less |
| VPA voltage | 4.8 V or more |
| Either of the following conditions is met | Condition A or B |
| A. VPA2 voltage when VPA is 0.04 V or more | 1.2 V or less |
| B. VPA2 voltage when VPA is 0.4 to 3.45 V | 4.8 V or more |
| VPA2 voltage when VPA is 0.04 V or more | 1.2 V or less |
| VPA2 voltage when VPA is 0.4 to 3.45 V | 4.8 V or more |
| Either of following conditions is met: | Condition A or B |
| Condition A | - |
| Difference between VPA and VPA 2 voltages | 0.02 V or less |
| Condition B | - |
| VPA voltage | 0.4 V or less |
| VPA2 voltage | 1.2 V or less |
| Parameter | Standard Value |
| VPA voltage | 0.4 V to 4.8 V |
| VPA2 voltage | 1.2 V to 4.8 V |
| Difference between VPA and VPA2 voltages | More than 0.02 V |

| 1.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION NO. 1 AND NO. 2) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the values displayed on the tester.
| Accelerator Pedal Operation | Accelerator Position No. 1 | Accelerator Position No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A15 Accelerator Pedal Position (APP) sensor connector.
Disconnect the E4 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VPA1 (A15-6) - VPA (E4-18) | Below 1 Ω |
| EP1 (A15-5) - EPA (E4-20) | Below 1 Ω |
| VCP1 (A15-4) - VCPA (E4-26) | Below 1 Ω |
| VPA2 (A15-3) - VPA2 (E4-19) | Below 1 Ω |
| EP2 (A15-2) - EPA2 (E4-21) | Below 1 Ω |
| VCP2 (A15-1) - VCP2 (E4-27) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VPA1 (A15-6) or VPA (E4-18) - Body ground | 10 kΩ or higher |
| EP1 (A15-5) or EPA (E4-20) - Body ground | 10 kΩ or higher |
| VCP1 (A15-4) or VCPA (E4-26) - Body ground | 10 kΩ or higher |
| VPA2 (A15-3) or VPA2 (E4-19) - Body ground | 10 kΩ or higher |
| EP2 (A15-2) or EPA2 (E4-21) - Body ground | 10 kΩ or higher |
| VCP2 (A15-1) or VCP2 (E4-27) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A15 APP sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCPA (E4-26) - EPA (E4-20) | 4.5 to 5.0 V |
| VCP2 (E4-27) - EPA2 (E4-21) | 4.5 to 5.0 V |
Reconnect the APP sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items on the tester: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 | A |
| No output | B |
|
| ||||
| A | ||
| ||