Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here

HINT:
This DTC relates to the Accelerator Pedal Position (APP) sensor.


DESCRIPTION

Refer to DTC P2120 .

DTC No.
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator position (APP) sensor
  2. ECM

MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the voltage outputs of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and the DTC is set.

MONITOR STRATEGY


Related DTCs
P2121: Accelerator pedal position (APP) sensor rationality
Required Sensors / Components (Main)
APP sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
Either of the following conditions is met.
Condition 1 or 2
1. Ignition switch
ON
2. Electronic throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


Difference between VPA1 voltage (learned value) and VPA2 voltage (learned value)
Less than 0.4 V, or more than 1.2 V

FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION NO. 1 AND NO. 2)


    FI07052E14
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Read the values displayed on the tester.

    Standard voltage:
    Accelerator Pedal Operation
    Accelerator Position No. 1
    Accelerator Position No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V



OK
Go to step 4
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A114633E09
  1. Disconnect the A15 Accelerator Pedal Position (APP) sensor connector.

  1. Disconnect the E4 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Check for open:
    Tester Connection
    Specified Condition
    VPA1 (A15-6) - VPA (E4-18)
    Below 1 Ω
    EP1 (A15-5) - EPA (E4-20)
    Below 1 Ω
    VCP1 (A15-4) - VCPA (E4-26)
    Below 1 Ω
    VPA2 (A15-3) - VPA2 (E4-19)
    Below 1 Ω
    EP2 (A15-2) - EPA2 (E4-21)
    Below 1 Ω
    VCP2 (A15-1) - VCP2 (E4-27)
    Below 1 Ω
    Check for short:
    Tester Connection
    Specified Condition
    VPA1 (A15-6) or VPA (E4-18) - Body ground
    10 kΩ or higher
    EP1 (A15-5) or EPA (E4-20) - Body ground
    10 kΩ or higher
    VCP1 (A15-4) or VCPA (E4-26) - Body ground
    10 kΩ or higher
    VPA2 (A15-3) or VPA2 (E4-19) - Body ground
    10 kΩ or higher
    EP2 (A15-2) or EPA2 (E4-21) - Body ground
    10 kΩ or higher
    VCP2 (A15-1) or VCP2 (E4-27) - Body ground
    10 kΩ or higher

  1. Reconnect the APP sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
OK


3.REPLACE ACCELERATOR PEDAL ROD
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2121
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)