Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM3650E _59 Vehicle Exterior _079908 LIGHTING (EXT) _0387818 HEADLIGHT ASSEMBLY N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:
·

Observe the operating instructions for the headlight adjusting device.

·

Do not perform headlight adjustment immediately after lowering the vehicle on the vehicle hoist. In this case, move the vehicle for approx. 15 m on its own wheels before headlight adjustment.



HINT:

Description is for left component only. Procedure on the right side is identical.


PROCEDURE

Hide 1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT

a.

Vehicle parked on level ground.


b.

Check correct adjustment of headlights in relation to engine compartment lid (gap dimensions).

Click hereVehicle Exterior>DOOR / HATCH>HOOD>ON-VEHICLE INSPECTION


c.

Check tire pressure and correct if necessary.


d.

Apply load equivalent to one person on driver's seat (75 kg, 165 lb).


e.

Vehicle with full fuel tank or appropriate additional weight in luggage compartment.


Hide 2. PREPARE FOR HEADLIGHT AIMING (Using a headlight aim test machine)

a.

Adjust the headlight aim in accordance with the headlight aim test machine instructions.


Hide 3. PREPARE FOR HEADLIGHT AIMING (Using a screen)

a.
E443687C01
0.635,1.156 0.948,1.313 0.313,0.156 10 false *a 1.094,1.729 1.406,1.885 0.313,0.156 10 false *b
*a 90°
*b 25 m or 3 m (82 ft. or 9.84 ft.)


Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·
E443688C01
2.333,0.917 3.083,0.917 true 3.125,0.833 3.344,1.021 0.219,0.188 10 true *a
*a Center Mark


Create a 25 m (82 ft.) distance between the vehicle (center marks of the headlight) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 25 m (82 ft.) between the vehicle (center marks of the low beam) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration).



b.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E443689E02
0.896,1.135 0.896,0.708 0.896,0.708 1.167,0.708 true 4.188,1.125 4.188,0.698 4.188,0.698 4.458,0.698 true 1.167,2.26 0.896,2.26 0.896,2.26 0.896,1.802 true 4.458,2.271 4.188,2.271 4.188,2.271 4.188,1.813 true 1.198,1.219 1.656,1.417 0.458,0.198 10 false 90° 4.49,1.219 4.948,1.417 0.458,0.198 10 false 90° 1.229,0.625 2.604,0.823 1.375,0.198 10 false V RH Line 4.51,0.625 5.885,0.823 1.375,0.198 10 false V RH Line 1.229,2.188 2.604,2.385 1.375,0.198 10 false V LH Line 3.354,1.385 3.854,1.573 0.5,0.188 10 false V Line 6.635,1.385 7.135,1.573 0.5,0.188 10 false V Line 4.521,2.188 5.896,2.385 1.375,0.198 10 false V LH Line 0.271,3.479 0.771,3.667 0.5,0.188 10 false H Line 3.563,3.479 4.063,3.667 0.5,0.188 10 false H Line 1.198,3.646 1.656,3.844 0.458,0.198 10 false 90° 4.5,3.646 4.958,3.844 0.458,0.198 10 false 90° 1.365,4.083 2.281,4.281 0.917,0.198 10 false 25 m 4.74,4.094 5.198,4.292 0.458,0.198 10 false 3 m 1.146,0.125 3.583,0.396 2.438,0.271 12 false Alignment distance is 25 m: 4.375,0.125 6.813,0.396 2.438,0.271 12 false Alignment distance is 3 m:

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
E257183C18
1.17,0.275 1.331,0.419 0.161,0.143 10 *a 1.823,0.275 1.984,0.419 0.161,0.143 10 *b 2.446,0.275 2.607,0.419 0.161,0.143 10 *c 2.936,0.851 3.097,0.994 0.161,0.143 10 *d 0.547,1.698 0.708,1.841 0.161,0.143 10 *e
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:
E443688C01
2.333,0.917 3.083,0.917 true 3.125,0.833 3.344,1.021 0.219,0.188 10 true *a
*a Center Mark


Mark the headlight assembly center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight LED unit as the center mark.


i.

H Line (Headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight center marks.


ii.

V LH Line and V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center mark of the headlight).



Hide 4.INSPECT HEADLIGHT AIMING

a.

Start the engine.


b.
E420007

Light switch must be in "low beam/driving light" position (1).

NOTICE:

Do not carry out the headlight adjustment in the "automatic driving lights control" light switch position (2).



c.

Wait 80 seconds after switching on lights. During this time, do not move the vehicle and avoid vibrations.

NOTICE:
·

Wheels must be in the straight-ahead position.

·

Do not move the vehicle and steering wheel during the measuring and adjustment procedures.




d.

Cover the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



e.

Check if the cutoff line matches the preferred cutoff line in the following illustration.

E234067E32
1.167,2.25 1.333,2.25 1.333,2.25 1.49,1.875 false 4.667,2.25 4.833,2.25 4.833,2.25 5,1.875 false 1.99,1.844 2.323,0.75 2.323,0.75 2.5,0.75 true 5.469,1.844 5.802,0.75 5.802,0.75 6,0.75 true 0.354,2.833 3.917,3.781 3.563,0.948 10 false The illustration shown is for an LHD vehicle. RHD vehicles will project a headlight pattern that is a mirror image. 0.917,0.167 3.271,0.688 2.354,0.521 12 false Alignment distance is 25 m: 4.333,0.167 6.615,0.583 2.281,0.417 12 false Alignment distance is 3 m: 0.167,1.5 2,1.75 1.833,0.25 10 false H Line 3.813,1.771 4.354,1.99 0.542,0.219 10 false 30 mm 1.479,2.26 2.083,2.458 0.604,0.198 10 false 250 mm 0.219,1.76 0.802,1.958 0.583,0.198 10 false 250 mm 3.104,1.76 3.729,1.969 0.625,0.208 10 false 700 mm 6.604,1.74 7.104,1.948 0.5,0.208 10 false 84 mm 5.01,2.25 5.531,2.5 0.521,0.25 10 false 30 mm 1.281,1.24 1.802,1.49 0.521,0.25 10 false 50 mm 4.76,1.229 5.281,1.479 0.521,0.25 10 false 6 mm 0.521,2.167 1.188,2.667 0.667,0.5 10 false Preferred Cutoff Line 4.021,2.167 4.688,2.667 0.667,0.5 10 false Preferred Cutoff Line 3.667,1.5 5.5,1.75 1.833,0.25 10 false H Line 1.333,0.667 3.167,0.917 1.833,0.25 10 false V LH Line 4.833,0.667 6.667,0.917 1.833,0.25 10 false V LH Line 1.333,0.917 3.167,1.167 1.833,0.25 10 false V RH Line 4.833,1 6.667,1.25 1.833,0.25 10 false V RH Line 2.583,0.667 3.167,0.917 0.583,0.25 10 false Point A 6.115,0.667 6.708,0.917 0.594,0.25 10 false Point A 5.51,2.26 6.031,2.51 0.521,0.25 10 false 30 mm 2.021,2.26 2.625,2.458 0.604,0.198 10 false 250 mm

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82 ft.):

The low beam cutoff line should be between 50 mm (1.97 in.) and 700 mm (27.6 in.) below the H line as well as 250 mm (9.84 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be between 6 mm (0.227 in.) and 84 mm (3.31 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 25 m (82 ft.):

The horizontal line of the preferred low beam cutoff line is 250 mm (9.84 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.




f.

Turn on the high beams and check if the center of intensity for each high beam matches the preferred center of the intensity in the illustration.

E235330E51
1.99,1.594 2.26,0.583 2.26,0.583 2.406,0.583 true 5.479,1.604 5.76,0.594 5.76,0.594 5.896,0.594 true 1.167,0.083 3.229,0.448 2.063,0.365 12 false Alignment distance is 25 m: 4.667,0.083 6.729,0.448 2.063,0.365 12 false Alignment distance is 3 m: 1.302,0.531 1.958,0.844 0.656,0.313 10 false V LH Line 0.51,1.51 0.938,1.813 0.427,0.302 10 false H Line 4.802,2.198 5.385,2.427 0.583,0.229 10 false 60 mm 1.302,2.208 1.885,2.396 0.583,0.188 10 false 500 mm 4,1.51 4.427,1.813 0.427,0.302 10 false H Line 6.573,1.76 7.156,2.01 0.583,0.25 10 false 30 mm 6.573,1.406 7.094,1.615 0.521,0.208 10 false 21 mm 3.135,1.76 3.719,1.927 0.583,0.167 10 false 250 mm 3.125,1.406 3.781,1.573 0.656,0.167 10 false 175 mm 2.479,0.51 3.688,0.917 1.208,0.406 10 false Center of Intensity 5.948,0.521 7.125,1.115 1.177,0.594 10 false Center of Intensity 1.302,0.823 1.958,1.188 0.656,0.365 10 false V RH Line 4.802,0.521 5.458,0.833 0.656,0.313 10 false V LH Line 4.802,0.813 5.458,1.177 0.656,0.365 10 false V RH Line 2.125,2.208 2.708,2.396 0.583,0.188 10 false 500 mm 5.667,2.198 6.25,2.427 0.583,0.229 10 false 60 mm

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82 ft.):

The high beam center of intensity should be within 175 mm (6.89 in.) above and 250 mm (9.84 in.) below the H line as well as 500 mm (19.7 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 21 mm (0.827 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.




Hide 5.ADJUST HEADLIGHT AIMING

a.
E414435

Turn both covers (1) above the adjusting screws for the light setting by 90° and remove.


b.
E454888

Adjust the aim vertically:

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

When adjusting the vertical axis of the headlight, the horizontal axis will also change. It is necessary to adjust the vertical position first, and then correct the horizontal position.

·

If it is not possible to correctly adjust headlight aim, check the headlight unit and headlight unit lens installation.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.



i.

Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver (1).



c.

Adjust the aim horizontally:

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If it is not possible to correctly adjust headlight aim, check the headlight unit and headlight unit lens installation.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.



i.

Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver (2).



d.
E414435

Install the covers (1) above the adjusting screws for the light setting and turn by 90°.