Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER DAMPER
RM3650E _53 Suspension _079981 REAR SUSPENSION _0387961 REAR SUSPENSION MEMBER DAMPER A

REAR SUSPENSION  REAR SUSPENSION MEMBER DAMPER  INSTALLATION  


PROCEDURE

Hide 51249 1.INSTALL REAR SUSPENSION MEMBER DAMPER

a.

Replace the E12 bolt.


b.

Position the rear suspension member damper and tighten the E12 bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 2.INSTALL VIBRATION ABSORBER

a.

Position the vibration absorber.


b.

Replace the bolt.


c.
C417117C01
1.76,0.927 2.49,0.917 true 1.333,1.385 1.667,1.302 true 1.229,0.969 1.625,0.979 true 2.344,2.031 2.594,2.25 0.25,0.219 10 true *a 0.854,1.333 1.271,1.552 0.417,0.219 10 true SST 0.917,0.885 1.167,1.104 0.25,0.219 10 true *b
*a Torque Wrench Fulcrum Length
*b 13 mm Union Nut Wrench


Tighten the bolt (1) with the special tool 2 444 999, SST and 13 mm union nut wrench.

SST
09961-00950  
09700-WA140  

Torque:
Specified tightening torque : 56 N*m (571 kgf*cm, 41 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 13 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

28 N*m (286 kgf*cm, 21 ft.*lbf)




d.

Using a digital angle torque wrench, tighten the bolt an additional 90°.

HINT:
·
C417458C02
2.5,1.542 2.5,1.208 false 0.49,2.969 0.281,3.208 false 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 2.448,1.583 2.76,1.74 0.313,0.156 10 false *b 0.177,3.229 0.49,3.385 0.313,0.156 10 false *c 0.771,0.156 1.083,0.313 0.313,0.156 10 false *d 2.49,0.448 2.802,0.604 0.313,0.156 10 false *e 1.229,2 1.542,2.156 0.313,0.156 10 false *f 3.104,2.406 3.417,2.563 0.313,0.156 10 false *g 0.938,2.927 1.25,3.083 0.313,0.156 10 false *h
*a Example
*b Before Tightening
*c After Tightening
*d Set Angle Display
*e Setting the Specified Angle
*f Tightening Angle Display
*g LED Notification
*h Buzzer Notification



·

When using the digital angle torque wrench, set the wrench to the specified tightening angle before use.

·

When using the digital angle torque wrench, check the tightening angle display while performing the work.

·

When tightening reaches the set angle, the buzzer will sound and a blue LED will illuminate.