BASIC REPAIR HINT
HINTS ON OPERATIONS
| 1 | Attire | ·
Always wear a clean uniform. ·
A hat and safety shoes must be worn. |
| 2 | Vehicle protection | Prepare a grille cover, fender cover, seat cover and floor mat before starting work. |
| 3 | Safety procedures | ·
When working with 2 or more persons, be sure to check the safety of one another. ·
When working with the engine running, make sure to provide ventilation for exhaust fumes in the workshop. ·
If working on high temperature, high pressure, rotating, moving or vibrating parts, wear appropriate safety equipment and take extra care not to injure yourself or others. ·
When jacking up the vehicle, be sure to support the vehicle at the specified locations with safety stands. ·
When lifting up the vehicle, use appropriate safety equipment. |
| 4 | Preparation of tools and measuring equipment | Before starting work, prepare a tool stand, SST, measuring equipment, oil, and any replacement parts required. |
| 5 | Removal and installation, disassembly and assembly operations | ·
Diagnose with a thorough understanding of proper procedures and of the reported problem. ·
Before removing any parts, check the general condition of the assembly and for deformation and damage. ·
If the procedure is complicated, take notes. For example, note the total number of electrical connections, bolts or hoses removed. Add matchmarks to ensure reassembly of components in the original positions. Temporarily mark hoses and their fittings if needed. ·
Clean and wash the removed parts if necessary and assemble them after a thorough check. |
| 6 | Removed parts | ·
Place the removed parts in a separate box to avoid mixing them up with new parts or contaminating the new parts. ·
For non-reusable parts such as gaskets, O-rings and self-locking nuts, replace them with new ones as instructed in this manual. ·
Retain the removed parts for customer inspection, if requested. |
| 7* | Checks to perform after work is finished | ·
Make sure that removed and installed parts (oil filler cap, level dipstick, floor mat, etc.) are properly installed/tightened. ·
Make sure that none of the cloths or tools that were used have been left in the engine compartment or within the vehicle. ·
Check that there are no oil leaks. |
*: Be sure to perform these checks properly, not performing these checks properly after finishing work can lead to a serious accident or injury.
JACKING UP AND SUPPORTING THE VEHICLE
Care must be taken when jacking up and supporting the vehicle. Be sure to lift and support the vehicle at the proper locations.
| *a | Seal Lock Adhesive |
PRECOATED PARTS
Precoated parts are bolts and nuts that are coated with seal lock adhesive at the factory.
If a precoated part is retightened, loosened or moved in any way, it must be recoated with the specified adhesive.
When reusing a precoated part, clean off the old adhesive and dry the part with compressed air. Then apply new seal lock adhesive appropriately to that part.
Some seal lock agents harden slowly. You may have to wait for the seal lock adhesive to harden.
GASKETS
When necessary, use a sealant on gaskets to prevent leaks.
BOLTS, NUTS AND SCREWS
Carefully follow all of the specifications for tightening torque. Always use a torque wrench.
Make sure that no foreign matter (burrs, paint, etc.) gets trapped under the heads of the bolts and nuts when tightening them.
| *a | NG |
| *b | OK |
FUSES
When inspecting a fuse, check that the wire of the fuse is not broken.
If the wire of a fuse is broken, confirm that there are no shorts in its circuit.
When a fuse is replaced, a fuse with the same amperage rating must be used.
| Illustration | Symbol | Part Name | Abbreviation |
|---|---|---|---|
|
|
FUSE | FUSE |
|
|
MEDIUM CURRENT FUSE | M-FUSE |
|
|
HIGH CURRENT FUSE | H-FUSE |
|
|
FUSIBLE LINK | FL |
|
|
CIRCUIT BREAKER | CB |
|
|
FUSIBLE LINK | FL |
UNLOCKING AND DISCONNECTING DIFFERENT PLUG CONNECTIONS
The document describes unlocking and disconnecting different types of plug connections.
Differences in the details of the size and shape of the plug connections are possible.
Press lock and open release clip in direction of arrow.
Disconnect plug connection.
Press lock and open release clip in direction of arrow.
Disconnect plug connection.
Open release clip in direction of arrow and disconnect plug connection in direction of arrow.
Press lock and disconnect plug connection in direction of arrow.
Press lock and disconnect plug connection in direction of arrow.
Press lock and disconnect plug connection in direction of arrow.
Press lock and disconnect plug connection in direction of arrow.
Press lock and disconnect plug connection in direction of arrow.
Press lock and disconnect plug connection in direction of arrow.
Press the lock and detach plug connection.
Press the lock and detach plug connection.
Press the locks on both sides and detach plug connection.
Press the lock and detach plug connection.
Press lock and open release clip in direction of arrow.
Disconnect plug connection.
Press the lock and detach plug connection.
Pull out lock and press.
Disconnect plug connection.
Press the locks on both sides and detach plug connection.
Press the locks on both sides and detach plug connection.
Press the lock and detach plug connection.
Plug connection on the power distribution box:
Press into the opening (2) using a screwdriver (1).
Pull off plug connection (3) upwards.
Plug connection on the power distribution box:
Lift lock (1) with a screwdriver.
Pull off plug connection (2) upwards.
Vibration resistant high power engine contacts:
For this connector type, increased forces come into play when disconnecting and closing.
Disconnect:
Pull out lock (1) downward in direction of arrow first.
Then press lock (1) down in direction of arrow and pull off connector.
Close:
A. Press connector (1) down to the end position at positions marked with the arrow.
B. Do not press connector (1) down through the lock.
C. Connector (1) is in the end position, lock (2) is not yet locked.
D. Press down lock (2) in the direction of arrow until the tip of the lock (2) at position (3) is visible.
Unlock / lock front light combination plug connection and replace housing after damage:
Press in locking lever at both sides until the lever is unlocked and can be moved.
Move lever upwards until it latches into place in the end position.
Once the lever is locked in the end position, remove plug connection upwards.
Unlock socket housing by lifting up each of the locking tabs.
Slide out after unlocking the socket housing.
Slide in socket housing up to limit position.
Lock socket housing into place in end position.
Sliding in up to limit position.
Activate plug-in procedure by moving lever downwards.
Important: the latch mechanism on both sides only works for a completed plug-in procedure.
Press to unlock on both sides.
15-pin housing:
A and B. To avoid any damage to individual connectors, the given connector assembly consisting of several individual connectors (1) and (2) must be released before disconnecting the plug connection.
C: released connector assembly.
Disconnecting connector assembly:
Release retaining hooks (1) in direction of arrow (detail image shows retaining hooks of individual connector).
Release connector (2) in direction of arrow from connector (1).
Airbag ignition circuit connector:
Note the safety information for working on vehicles with airbag systems prior to disconnecting the plug connection.
Pull the cap (1) in the direction of the arrow to unlock.
CLIPS
The removal and installation methods of typical clips used for vehicle body parts are shown in the table below.
If clips are damaged during a procedure, always replace the damaged clips with new ones.
| Shape (Example) | Removal/Installation |
|---|---|
|
Remove the clips with a clip remover or pliers.
|
|
Remove the clips using a clip remover or a screwdriver with its tip wrapped with protective tape.
|
|
Disengage the clips with a moulding remover to prevent panel damage.
|
|
Remove the clips by prying out the center pin using a clip remover and then prying out the shell.
|
|
Remove the clips by pushing out the center pin using a screwdriver and then prying out the shell.
|
CLAWS
The removal and installation methods of typical claws used for vehicle body parts are shown in the table below.
If claws are damaged during a procedure, always replace the cap or cover that has damaged claws with a new one.
| Shape (Example) | Illustration/Procedures |
|---|---|
|
Disengage the claws using a screwdriver with its tip wrapped with protective tape to remove the caps or covers.
|
|
Disengage the claws using a screwdriver with its tip wrapped with protective tape to remove the caps or covers.
|
|
Disengage the claws using a screwdriver with its tip wrapped with protective tape to remove the caps or covers.
|
HINGES, GUIDES, CLAMPS, PINS, ETC.
The removal and installation methods of typical hinges, guides, clamps and pins used for vehicle body parts are shown in the table below.
If clamps are damaged during a procedure, always replace the cap or cover that has damaged clamps with a new one.
| Shape (Example) | Removal/Installation |
|---|---|
|
Pull away from the pins to disengage.
|
|
Disengage the pins by pulling.
|
|
Remove the clamps with pliers.
|
|
Disengage the pins by pulling.
|
REMOVAL AND INSTALLATION OF VACUUM HOSES
| *a | Incorrect |
| *b | Correct |
To disconnect a vacuum hose, pull and twist it from the end of the hose. Do not pull it from the middle of the hose as this may damage the hose.
When disconnecting vacuum hoses, use tags to identify where they should be reconnected.
After completing any hose related repairs, double-check that the vacuum hoses are properly connected. The label under the hood shows the proper layout.
When using a vacuum gauge, never force the hose onto a connector that is too large. If a hose has been stretched, air may leak. Use a step-down adapter if necessary.
TORQUE WHEN USING TORQUE WRENCH WITH EXTENSION TOOL
Use the formula below to calculate special torque values for situations where SST or an extension tool is combined with a torque wrench.
T' = (L2/(L1 + L2))*T
| T' | Reading of torque wrench (N*m (kgf*cm, ft.*lbf)) |
| T | Torque (N*m (kgf*cm, ft.*lbf)) |
| L1 | Length of SST or extension tool (cm (in.)) |
| L2 | Length of torque wrench (cm (in.)) |
If an extension tool or SST is combined with a torque wrench and used to tighten to a torque specification in this manual, the actual torque will be excessive and parts will be damaged.
ELECTRONIC CONTROL
| *1 | Cable |
| *2 | Negative (-) Battery Terminal |
DISCONNECTING AND RECONNECTING CABLE TO NEGATIVE (-) BATTERY TERMINAL
Before performing work on electronic components, disconnect the cable from the negative (-) battery terminal to prevent damage to the electrical system or components.
When disconnecting the cable, turn the START-STOP button (engine switch) and headlight switch off and loosen the cable nut completely. Perform these operations without twisting or prying on the cable. Then disconnect the cable.
Pressing and holding the AUDIO button changes the power source mode to IG OFF.
Clock settings, radio settings, audio system memory, DTCs and other data will be cleared when the cable is disconnected from the negative (-) battery terminal. Write down any necessary data before disconnecting the cable.
HANDLING OF ELECTRONIC PARTS
To avoid damaging or destroying electrical components as a result of electrostatic discharge, when replacing electrical components, leave the replacement components in their original packaging until immediately before they are to be installed.
Do not open the cover or case of an ECU unless absolutely necessary. If the IC terminals are touched, the IC may be rendered inoperative by static electricity.
Do not touch the terminals of the connector to avoid damaging or destroying electrical components as a result of electrostatic discharge.
Electrical components which are particularly sensitive to electrostatic discharge (ECU, sensors, etc.) are marked with the ESD (Electrostatic Discharge) warning symbol.
Do not pull on the wires when disconnecting electronic connectors. Pull the connector itself.
| *a | Incorrect |
Do not drop electronic components, such as sensors or relays. If they are dropped on a hard surface, they should be replaced.
When cleaning the engine components with a pressure washer, protect the electronic components, air filter and emission-related components from water.
When measuring the resistance between terminals of a connector, insert the tester probe carefully to prevent the terminals from bending.
Never use an impact wrench to remove or install temperature switches or temperature sensors.
REMOVAL AND INSTALLATION OF CONTROL UNITS
Disconnecting the vehicle battery will cancel the fault memories of ECUs. Consequently, before disconnecting the car's battery, always interrogate the fault memories. Investigate stored faults and, once any faults have been remedied, cancel the fault memory.
ECU plugs should only ever be connected and disconnected while the START-STOP button (engine switch) is turned off.
Pressing and holding the AUDIO button changes the power source mode to IG OFF.
The removal and installation of components, relays, fuses etc. can cause faults to be stored in fault memories capable of self diagnosis. Always interrogate the fault memories after completing work on the electrical system.
Investigate stored faults and, once any faults have been remedied, cancel the fault memory.
If necessary, initialize power window unit.
REMOVAL AND INSTALLATION OF FUEL CONTROL PARTS
PLACE FOR REMOVING AND INSTALLING FUEL SYSTEM PARTS
Work in a location with good air ventilation that does not have welders, grinders, drills, electric motors, stoves or any other ignition sources nearby.
Never work in a pit or near a pit as fuel vapors will collect there.
REMOVING AND INSTALLING FUEL SYSTEM PARTS
Prepare a fire extinguisher before starting work.
To prevent static electricity, install a ground wire between the fuel changer and vehicle, and do not spray the surrounding area with water. Be careful when performing work in this area, as the floor surface will become slippery. Do not clean up gasoline spills with water, as this may cause the gasoline to spread, and possibly create a fire hazard.
Avoid using electric motors, work lights and other electric equipment that can cause sparks or high temperatures.
Avoid using iron hammers as they may create sparks.
Dispose of fuel-contaminated cloth separately using a fire resistant container.
REMOVAL AND INSTALLATION OF ENGINE INTAKE PARTS
If any metal particles enter intake system parts, they may damage the engine.
When removing and installing intake system parts, cover the openings of the removed parts and engine openings. Use adhesive tape or other suitable materials.
When installing intake system parts, check that no metal particles have entered the engine or installed parts.
HANDLING OF HOSE CLAMPS
| *1 | Clamp Track |
| *2 | Spring Type Clamp |
Before removing a hose, check the clamp position so that it can be reinstalled in the same position.
Replace any deformed or dented clamps with new ones.
When reusing a hose, attach the clamp on the clamp track portion of the hose.
For a spring type clamp, it may be necessary to spread the tabs slightly after installation by pushing them in the direction of the arrows as shown in the illustration.
FOR VEHICLES EQUIPPED WITH MOBILE COMMUNICATION SYSTEMS
Install the antenna as far away from the ECU and sensors of the vehicle electronic systems as possible.
Install the antenna and feeder at least 20 cm (7.87 in.) away from the ECUs and sensors of the vehicle electronic systems. For details about ECU and sensor locations, refer to the section on the applicable components.
Keep the antenna and feeder separate from other wiring as much as possible. This will prevent signals sent from the communication equipment from affecting vehicle equipment and vice versa.
Check that the antenna and feeder are correctly adjusted.
Do not install a high-powered mobile communication system.
HEADLIGHT INSPECTION OR MAINTENANCE
| *a | Illumination for 3 minutes or more prohibited if covered |
When the headlights are illuminated, do not cover the headlights for 3 minutes or more.
As the headlight outer lens is made of resin, the resulting heat created when covering the headlight for an extended period of time may deform the headlight.
ACTIONS TO BE TAKEN WHEN BATTERIES ARE DISCHARGED
Perform this procedure when the battery is fully discharged.
The following problems indicate that the battery is discharged:
No display appears on the instrument panel when the START-STOP button (engine switch) on (IG).
The engine does not start.
The headlights are dim.
The sound from the horn is weak.
Engage the parking brake.
Turn the START-STOP button (engine switch) off.
Pressing and holding the AUDIO button changes the power source mode to IG OFF.
Open the cover of the jump-starting terminal.
Using booster cables, connect the battery of the rescue vehicle to the battery of the stalled vehicle as shown in the illustration.
| *1 | Jump-starting Terminal | - | - |
| Connecting Sequence | Connecting Location |
|---|---|
| 1 | Jump-starting terminal of stalled vehicle |
| 2 | Positive (+) battery terminal of rescue vehicle |
| 3 | Position shown in the illustration on stalled vehicle |
| 4 | Negative (-) battery terminal of rescue vehicle |
Start the engine of the rescue vehicle and run the engine at a speed slightly higher than usual.
Start the engine of the stalled vehicle.
Once the engine starts, immediately disconnect the booster cable by performing the connection procedure in reverse. Do not leave the booster cables connected because they are not designed for recharging purposes.
PRECAUTIONS WHEN REPLACING PARTS AFTER A COLLISION
FRONT AXLE HUB
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSPECTION
REAR AXLE HUB
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSPECTION
STEERING COLUMN ASSEMBLY
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSPECTION
STEERING INTERMEDIATE SHAFT
Click hereSteering>STEERING COLUMN>STEERING INTERMEDIATE SHAFT>INSPECTION
STEERING GEAR
Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>INSPECTION
PRECAUTIONS FOR TOWING REAR WHEEL DRIVE VEHICLES
Use one of the following methods to tow the vehicle.
If the vehicle has trouble with the chassis or drivetrain, use method 1 (flatbed truck).
Do not use any towing method other than those shown above.
When selecting the shift position to N and rolling the vehicle at short distances.
Start the engine while depressing the brake pedal and enter the driving standby state.
If necessary, release the parking brake.
Depress the brake pedal.
Operate the selector lever and engage the shift position to N.
Stop the engine.
Driving standby state then remains switched on and the vehicle can now roll.
Shift position P is automatically engaged when driving standby state is switched off. There is a danger of damage to property.
Irrespective of driving standby state, shift position P is engaged automatically after approximately 35 minutes.