Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear)
RM3650E _56 Audio / Visual / Telematics _080021 PARK ASSIST / MONITORING _0388111 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


PROCEDURE

Hide 89348A 1.INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the No. 2 ultrasonic sensor retainer is necessary.

·

The illustration is for the LH side.

·

The orientation for the RH side is the opposite of the LH side.



a.

for rear side:

HINT:

If a No. 2 ultrasonic sensor retainer has been removed, replace it with a new one. Install the rear side ultrasonic sensor with a new No. 2 ultrasonic sensor retainer as a set to the rear bumper assembly.


i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Install the ultrasonic sensor O-ring.


iii.
E420782

Attach the claws (1) to install the rear side ultrasonic sensor (2) to a new No. 2 ultrasonic sensor retainer (3).

HINT:

To align the positions of the rear bumper assembly and ultrasonic sensor, assemble the rear side ultrasonic sensor (2) and No. 2 ultrasonic sensor retainer (3) as a single part.



iv.
E420776C01
0,0 0,0 false
V100144

No. 2 Ultrasonic Sensor Retainer Installation Surface


Using sandpaper (#80 is recommended), slightly roughen the installation surfaces of the No. 2 ultrasonic sensor retainer as shown in the illustration.


v.

Using cleaner, clean the areas that were roughened by the sandpaper.

Cleaner:

Cleaner R2



vi.

Peel off the release paper from the No. 2 ultrasonic sensor retainer.

HINT:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



vii.
E420787C01
0,0 0,0 false
V100155

Press area


Align the No. 2 ultrasonic sensor retainer and rear side ultrasonic sensor (2) with the scribed line (1) on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Make sure that the rear bumper assembly and the rear side ultrasonic sensor are properly aligned.

·

Detaching and reattaching a No. 2 ultrasonic sensor retainer will degrade its adhesive performance, so if reattachment is necessary, make sure to clean the installation surface again and replace the No. 2 ultrasonic sensor retainer with a new one.



HINT:

Press the area shown in the illustration with a force of to securely install the No. 2 ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the No. 2 ultrasonic sensor retainer and rear bumper assembly.



viii.

Attach the clamp.



b.

for rear corner side:

HINT:

If a No. 2 ultrasonic sensor retainer has been removed, replace it with a new one. Install the rear corner ultrasonic sensor with a new No. 2 ultrasonic sensor retainer as a set to the rear bumper assembly.


i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.


iii.

Install the ultrasonic sensor O-ring.


iv.
E420783

Attach the claws (1) to install the rear corner ultrasonic sensor (2) to a new No. 2 ultrasonic sensor retainer (3).

HINT:

To align the positions of the rear bumper assembly and ultrasonic sensor, assemble the rear corner ultrasonic sensor (2) and No. 2 ultrasonic sensor retainer (3) as a single part.



v.
E420777C01
0,0 0,0 false
V100144

No. 2 Ultrasonic Sensor Retainer Installation Surface


Using sandpaper (#80 is recommended), slightly roughen the installation surfaces of the No. 2 ultrasonic sensor retainer as shown in the illustration.


vi.

Using cleaner, clean the areas that were roughened by the sandpaper.

Cleaner:

Cleaner R2



vii.

Peel off the release paper from the No. 2 ultrasonic sensor retainer.

HINT:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



viii.
E420788C01
0,0 0,0 false
V100155

Press area


Align the No. 2 ultrasonic sensor retainer and rear corner ultrasonic sensor (2) with the scribed line (1) on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Make sure that the rear bumper assembly and the rear corner ultrasonic sensor are properly aligned.

·

Detaching and reattaching a No. 2 ultrasonic sensor retainer will degrade its adhesive performance, so if reattachment is necessary, make sure to clean the installation surface again and replace the No. 2 ultrasonic sensor retainer with a new one.



HINT:

Press the area shown in the illustration with a force of to securely install the No. 2 ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the No. 2 ultrasonic sensor retainer and rear bumper assembly.



ix.

Attach the clamp.



c.

for rear center side:

HINT:

If a No. 2 ultrasonic sensor retainer has been removed, replace it with a new one. Install the rear center ultrasonic sensor with a new No. 2 ultrasonic sensor retainer as a set to the rear bumper assembly.


i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Install the ultrasonic sensor O-ring.


iii.
E420784

Attach the claws (1) to install the rear center ultrasonic sensor (2) to a new No. 2 ultrasonic sensor retainer (3).

HINT:

To align the positions of the rear bumper assembly and ultrasonic sensor, assemble the rear center ultrasonic sensor (2) and No. 2 ultrasonic sensor retainer (3) as a single part.



iv.
E420778C01
0,0 0,0 false
V100144

No. 2 Ultrasonic Sensor Retainer Installation Surface


Using sandpaper (#80 is recommended), slightly roughen the installation surfaces of the No. 2 ultrasonic sensor retainer as shown in the illustration.


v.

Using cleaner, clean the areas that were roughened by the sandpaper.

Cleaner:

Cleaner R2



vi.

Peel off the release paper from the No. 2 ultrasonic sensor retainer.

HINT:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



vii.
E420789C01
0,0 0,0 false
V100155

Press area


Align the No. 2 ultrasonic sensor retainer and rear center ultrasonic sensor (2) with the scribed line (1) on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Make sure that the rear bumper assembly and the rear center ultrasonic sensor are properly aligned.

·

Detaching and reattaching a No. 2 ultrasonic sensor retainer will degrade its adhesive performance, so if reattachment is necessary, make sure to clean the installation surface again and replace the No. 2 ultrasonic sensor retainer with a new one.



HINT:

Press the area shown in the illustration with a force of to securely install the No. 2 ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the No. 2 ultrasonic sensor retainer and rear bumper assembly.



viii.

Attach the clamp.



Hide 89342A 2.INSTALL REAR CENTER ULTRASONIC SENSOR

HINT:
·

The illustration is for the LH side.

·

orientation for the RH side is the opposite of the LH side.



a.

When removing or replacing the rear center ultrasonic sensor:

i.

Install the ultrasonic sensor O-ring.


ii.
E415878

Attach the claws (1) to install the rear center ultrasonic sensor (2).



b.

Connect connector and lock.


Hide 89342B 3.INSTALL REAR SIDE ULTRASONIC SENSOR

HINT:
·

The illustration is for the LH side.

·

orientation for the RH side is the opposite of the LH side.



a.

When removing or replacing the rear side ultrasonic sensor:

i.

Install the ultrasonic sensor O-ring.


ii.
E415876

Attach the claws (1) to install the rear side ultrasonic sensor (2).



b.

Connect connector and lock.


Hide 89342 4.INSTALL REAR CORNER ULTRASONIC SENSOR

HINT:

Use the same procedure as for the rear side ultrasonic sensor.


Hide 5.INSTALL REAR BUMPER ASSEMBLY