Home › Engine / Hybrid System › B58 (INTAKE / EXHAUST) › CENTER EXHAUST PIPE
RM3650E _51 Engine / Hybrid System _080024 B58 INTAKE / EXHAUST _0388153 CENTER EXHAUST PIPE A

B58 INTAKE / EXHAUST  CENTER EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

CAUTION:
·

Hot exhaust system.

Risk of burning!

-

Any work must exclusively be carried out with an exhaust system that has cooled down.


·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.




HINT:
·

If the separation point is not marked by a punch mark in the pipe, determine the separation point by means of the pipe length on the new component.

·

Transfer the separation point to the faulty component and mark.

·

Cut through the faulty component at the marked point with a suitable tool.

·

Deburr the separation point and remove any swarf. There is a risk of remaining metal chips at the joint between the two pipes and/or swarf in the rear silencer.

·

Check the exhaust system for tightness after installation.



a.

for V-band Clamp:

i.

Have someone help position the front No. 2 exhaust pipe assembly in the center.


ii.

Check the rubber mounts for damage and replace, if necessary.


iii.

Replace nut.


iv.

Tighten the nut on the holder.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


v.
A442377

Release the nut (1) and remove the sealing ring (2).


vi.

Replace the exhaust pipe clamp.


vii.
A442378

Mount the sealing ring (1) on the exhaust pipe assembly.

NOTICE:

Ensure that the sealing ring (1) is correctly positioned for the exhaust pipe clamp (2).



viii.
A442379

Bend all sheet metal tabs over with a suitable tool, except those in the marked areas.


ix.
A442380

Mount the exhaust pipe clamp (1) on the sealing ring (2).

NOTICE:
·

Make sure that the exhaust pipe clamp (1) is positioned correctly on the sealing ring (2).

·
A442383

Make sure that the V-band clamprests against the sheet metal tabs after mounting (marks).




x.
A442381

Connect the front No. 2 exhaust pipe assembly (1) with the exhaust manifold converter sub-assembly (2) and position correctly.


xi.
A442382

Using a 16 mm deep socket wrench, tighten down screw (2).

NOTICE:

Make sure that exhaust pipe clamp (1) is fitted correctly.


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


xii.
A442391

Connect the front No. 2 exhaust pipe assembly to the rear silencer with the front No. 1 exhaust pipe clamp (for Rear) (2).


xiii.

Engage the front No. 1 exhaust pipe clamp (for Rear) (2) and tighten the nuts (1).

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)



b.

for Ribbon Clamp:

i.
A441588

Open the weld seam (1) with a hacksaw.


ii.

Remove the exhaust pipe clamp (2).


iii.

Replace the exhaust pipe clamp.


iv.

Have someone help insert the front No. 2 exhaust pipe assembly and position it at the front.


v.

Tighten the exhaust pipe clamp.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


vi.

Have someone help position the front No. 2 exhaust pipe assembly in the center.


vii.

Check the rubber mounts for damage and replace, if necessary.


viii.

Replace nut.


ix.

Tighten the nut on the holder.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


x.
A442391

Connect the front No. 2 exhaust pipe assembly to the rear silencer with the front No. 1 exhaust pipe clamp (for Rear) (2).


xi.

Engage the front No. 1 exhaust pipe clamp (for Rear) (2) and tighten the nuts (1).

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)



Hide 58252 2.INSTALL REAR FLOOR PANEL BRACE

Hide 57628E 3.INSTALL REAR FLOOR SIDE MEMBER COVER LH

Hide 57627G 4.INSTALL REAR FLOOR SIDE MEMBER COVER RH

HINT:

Use the same procedure as for the LH side.