Home › Engine / Hybrid System › B48 (LUBRICATION) › OIL PUMP
RM3650E _51 Engine / Hybrid System _080065 B48 LUBRICATION _0388372 OIL PUMP A

B48 LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 15100 1.INSTALL OIL PUMP ASSEMBLY

a.
A513639

Work centring sleeves (1) out of the crankcase in the direction of the arrow using conventional tools (2) and remove.


b.

Renew the centring sleeves (1).


c.
A441452

Insert oil pump set pins (1) in to the oil pump assembly (2) and install.


d.
A441453

Position oil pump drive shaft gear (1) on the oil pump assembly (2).

NOTICE:

The labelling on the oil pump drive shaft gear (1) must face away from the oil pump assembly (2).



e.
A444615

Replace the T45 bolt (1).


f.

Insert T45 bolt (1) and fit.

HINT:

The thread is a left-hand thread.



g.

Hold oil pump drive shaft gear with SST and tighten T45 bolt (1).

SST
09960-10010  (09962-01000, 09963-00700)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

HINT:

Conduct the following operation with the assistance of a second person.



h.

Using SST, tighten the T45 bolt (1) an additional 90°.

SST
09900-WA010  

HINT:
C417459C04
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




i.
A441229

Make sure the O-ring (1) is installed correctly.

NOTICE:

The O-ring (1) must not be damaged or missing.



j.
A441228

Feed the oil pump assembly (1) into the oil pump drive chain sub-assembly (2) and position it.


k.
A441449

Replace E10 bolts (1).


l.

Tighten the E10 bolts (1).

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


m.

Using SST, tighten the E10 bolts (1) an additional 45°.

SST
09900-WA010  

HINT:
C417459C04
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




Hide 12101 2.INSTALL OIL PAN SUB-ASSEMBLY