Home › Engine / Hybrid System › B48 (LUBRICATION) › OIL PAN
RM3650E _51 Engine / Hybrid System _080065 B48 LUBRICATION _0394471 OIL PAN A

B48 LUBRICATION  OIL PAN  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ENGINE OIL LEVEL SENSOR

a.
A441472

Replace engine oil level sensor gasket (1).


b.
A444623

Install the engine oil level sensor (2).


c.

Temporarily tighten nuts (1).

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


d.

Fully tighten nuts (1).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12101 2.INSTALL OIL PAN SUB-ASSEMBLY

NOTICE:
·

Contaminant or foreign body.

Contamination can result in malfunctions, operating failure or leaks.

-

Adhere to the utmost cleanliness.

-

Protect components from contamination e.g. by covering.

-

Close off line connections with seal plugs.



·

Damage to the surface.

The use of metal-cutting tools (e.g. emery cloth) to clean the surfaces can damage them and lead to leaks or engine damage.

-

Do not use any metal-cutting tools.




a.
A444617

Remove coarse seal packing remains on the sealing surface of the cylinder block (1) and the sealing surface on the oil pan sub-assembly.

NOTICE:

The sealing surfaces must be free from oils, grease and cleaning agents.



b.
A444618

Remove fine seal packing remains on the sealing surface of the oil pan sub-assembly (1) and the sealing surface on the cylinder block.

NOTICE:

The sealing surfaces must be free from oils, grease and cleaning agents.



c.

Load the sealer gun with the seal packing.

Seal Packing:

Loctite 5970 Flange Sealant



d.
A441663

Apply sealing bead (1) with the seal packing in the marked area along the inner edge.

Height of the Sealing Bead:

2.0 to 2.5 mm (0.0787 to 0.0984 in.)


NOTICE:

The maximum application time of the seal packing is 12 minutes.



e.

Completely encircle the oil return orifice (arrow) with the sealing compound.


f.

Install oil pan sub-assembly to top front.


g.

Hand-tighten all oil pan sub-assembly bolts but do not tighten completely.


h.
A441199

Tighten transmission E10 bolts (1).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


i.
A441200

Tighten down E10 bolts (1) and (2).

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


j.
A441246

Tighten the E10 bolts (1) to (7).

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


k.
A441245

Tighten the E10 bolts (1) to (7).

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


l.
A441247

Tighten the E10 bolts (1), (2) and (3).

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


m.
A441198

Mount cable with the clips (2) on the oil pan sub-assembly.


n.

Connect connector (1) and lock.

HINT:

The connector (1) must engage audibly.



Hide 28100 3.INSTALL STARTER ASSEMBLY

Hide 51201 4.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 6.INSPECT FOR ENGINE OIL LEAK