Home › Engine / Hybrid System › B58 (FUEL) › FUEL INJECTOR
RM3650E _51 Engine / Hybrid System _080099 B58 FUEL _0388620 FUEL INJECTOR A

B58 FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 1.REPLACE FUEL INJECTOR SEAL

NOTICE:
·

Damage to the injector tips and Teflon ring.

Improper handling of the injector tips and Teflon ring can lead to malfunctioning of the injector.

-

Avoid mechanical contact with injector tip.

-

When exchanging Teflon ring, hands and work surface must be clean and free of oil. Do not use any lubricating agents.

-

Do not use fingernails to slide Teflon ring on.




SST
09200-WA980  

HINT:

Before re-installing the injector, the Teflon ring must be replaced. Once a Teflon ring has been installed, it may not be re-used. New injectors are supplied with a new Teflon ring.

After the installation of a new Teflon ring on the injectors, the injector must be installed in the cylinder head within 10 minutes or protected with protective caps; otherwise, the Teflon ring will swell.


a.
A441570

Before installing the injectors: Replace the Teflon rings (1).


b.

Avoid mechanical contact with injector tip (2).


c.
A441571

Remove Teflon ring (1) by using special tool 2 452 959 from injector (2).

SST
09902-WA020  


d.

If necessary, use a lint-free cloth to clean the cylindrical part of the injector tip. Do not use ultrasonic sound or other auxiliary materials.

i.

The injector tip must not be cleaned.



e.
A441581

For the installation of the new Teflon rings: Use the set of special tools 2 448 401:

SST
09902-WA010  


f.
A441574

Slide the new Teflon ring (1) onto the installation cone (2) from the set of special tools 2 448 401.

SST
09902-WA010  


g.
A441572

Make sure that the installation position of the assembly sleeve (1) from the set of special tools 2 448 401 is correct.

SST
09902-WA010  

HINT:

The larger diameter of the assembly sleeve (1) must point to the injector tip.



h.
A441573

Make sure that the installation position of the assembly sleeve (1) from the set of special tools 2 448 401 is correct.

SST
09902-WA010  

NOTICE:

The assembly sleeve (1) is not mounted correctly when the smaller diameter points to the injector tip.



i.
A441575

Mount the Teflon ring (2) with the installation cone (1) from the set of special tools 2 448 401 on the injector tip .

SST
09902-WA010  


j.
A441576

Use the sliding sleeve (1) from the set of special tools 2 448 401 to push the Teflon ring (2) in to the groove (3) on the injector in the direction of arrow.

SST
09902-WA010  


k.
A441577

Thread out the sliding sleeve (1) from the set of special tools 2 448 401 in the direction of the arrow and remove.

SST
09902-WA010  


l.
A441578

Thread out the installation cone (1) from the set of special tools 2 448 401 in the direction of the arrow and remove.

SST
09902-WA010  


m.
A441579

Make sure that the expanded Teflon ring (1) is properly inserted in the groove (2) of the injector (3) and can be moved easily with your fingers.


n.
A441580

Calibrate the expanded Teflon ring with the assembly sleeve (1) from the set of special tools 2 448 401 to the installation dimension in the direction of the arrow.

SST
09902-WA010  


o.

Perform rotational movements in increments of 180° in sync with the pull-off movement. Perform the movements slowly and not jerky.

HINT:

This calibrates the Teflon ring (1) to the installation dimension.



p.

Thread out and remove the assembly sleeve (1).


q.
A441582

Check for correct installation dimension of the Teflon ring (1).

HINT:
·

indicates a correct installation dimension of the Teflon ring.

·

indicates an incorrect installation dimension of the Teflon ring.




Hide 23250 2.INSTALL FUEL INJECTOR ASSEMBLY (for Front Side)

NOTICE:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.


a.
A441729

Mount the holder (1) above the bayonet fitting (2) on the injector.


b.

If the holder (1) has a cast lug: Make sure that the holder is installed in the correct position.


c.
A441730

If applicable, note the position of the cast lug:

HINT:

The holder is mounted correctly when the cast lug is located at the rear.



d.
A441731

If applicable, note the position of the cast lug:

NOTICE:
·

Damage to injectors.

Weld seams on the injector may tear due to incorrect distances between the rail and injector so that the injector must be replaced.

-

Insertion of the distance gauge is compulsory.

-

Replace distance gauge, if a thickness of 8.5 mm is no longer given in the distance gauge.




HINT:

The holder is mounted incorrectly when the cast lug (1) is in front.



e.
A441732

Use the special tool (distance gauge) 2 358 022 (1).

SST
09200-WA830  


f.
A441733

Replace bolts.


g.

Mount the injectors with the holders and the bolts (1) on the rail.


h.

Keep the rail on a clean table in such a way that the openings on the rail for the injectors point upwards.

NOTICE:

The electrical injector connections must point to the fuel pressure sensor.



i.

Slide the special tool (distance gauge) 2 358 022 (2) between the holders and the rail onto the injector head.

SST
09200-WA830  


j.

Make sure that the special tool (distance gauge) 2 358 022 (2) rests flat on the retaining bridge.

SST
09200-WA830  


k.

Tighten both screws (1) evenly by hand until the special tool (distance gauge) 2 358 022 (2) rests flat against the rail and the holder.

SST
09200-WA830  


l.
A441734

Remove the special tool (distance gauge) 2 358 022 (1).

SST
09200-WA830  


m.

Repeat this operation for all injectors.


n.
A441735

Check injectors for loose fit at the rail.


o.

Align the electrical injector connections parallel to the rail.

i.

The injectors must move freely.



p.
A441532

Change screws (A) to (D).


q.

Attach the rail (1) with the injectors to the cylinder head from the top.


r.

Make sure the injector tips catch the corresponding bore holes in the cylinder head.


s.

Make sure the guides on the injector are properly inserted into the guide bores in the cylinder head.


t.

Press downwards until resistance is felt; position the screws (M6x70) (A), (B), (C) and (D) and hand-tighten them.


u.

Set torque wrench to 2 Nm.


v.

Tighten the screws (A,) (D), (B) and (C) at 90° each in an alternating order using the torque wrench until the rail rests onthe cylinder head.

i.

The figure shows the rail resting flat against the cylinder head.

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.




w.

Tighten E8 bolt (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


x.

Tighten E8 bolt (D).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


y.

Tighten E8 bolt (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


z.

Tighten E8 bolt (C).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


aa.

Connect and lock the connector (2).

i.

The connector (2) must engage audibly.



ab.
A441496

Make sure that the rail (1) rests flat against the cylinder head.


ac.
A441534

Attach a socket to an extension.

NOTICE:

Do not use a reversible ratchet or torque wrench.



ad.

Tighten the screws alternately in pairs ((1) with (2), (3) with (4), (5) with (6)) at 90° until hand-tight.


ae.

Set the torque wrench.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.



af.

Screw the E6 bolts according to the following plan:

i.

Fuel injector 1:


ii.

Tighten E6 bolts (1) at an angle of rotation of 90° +/- 15° with the torque wrench.


iii.

Tighten E6 bolts (2) at an angle of rotation of 90° +/- 15° with the torque wrench.


iv.

Repeat the operations for E6 bolts (1) and (2) until both bolts reach a torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


v.

Fuel injector 2:


vi.

Tighten E6 bolts (3) at an angle of rotation of 90° +/- 15° with the torque wrench.


vii.

Tighten E6 bolts (4) at an angle of rotation of 90° +/- 15° with the torque wrench.


viii.

Repeat the operations for E6 bolts (3) and (4) until both bolts reach a torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ix.

Injector 3:


x.

Tighten E6 bolts (5) at an angle of rotation of 90° +/- 15° with the torque wrench.


xi.

Tighten E6 bolts (6) at an angle of rotation of 90° +/- 15° with the torque wrench.


xii.

Repeat the operations for E6 bolts (5) and (6) until both bolts reach a torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



ag.
A441535

Mark all bolts (1) to (6) with a vertical line (see figure).


ah.

Tighten screws using an angle of rotation.

i.

Tighten E6 bolts (1) at an angle of rotation of 90° +/- 15°.


ii.

Tighten E6 bolts (2) at an angle of rotation of 90° +/- 15°.


iii.

Tighten E6 bolts (3) at an angle of rotation of 90° +/- 15°.


iv.

Tighten E6 bolts (4) at an angle of rotation of 90° +/- 15°.


v.

Tighten E6 bolts (5) at an angle of rotation of 90° +/- 15°.


vi.

Tighten E6 bolts (6) at an angle of rotation of 90° +/- 15°.



ai.
A441536

Check if all E6 bolts (1) to (6) have been tightened with a 90° +/- 15° angle of rotation.

i.

All marks (lines) must be horizontal (see figure).



aj.
A441533

Unscrew the E8 bolts (A) to (D).

i.

It is imperative that the bolts are unscrewed.

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.




ak.

Tighten E8 bolts (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


al.

Tighten E8 bolts (D).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


am.

Tighten E8 bolts (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


an.

Tighten E8 bolts (C).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ao.

Mark all bolts (A) to (D) with a vertical line (see figure).


ap.
A441537

Tighten E8 bolts (A) to (D) to a 90° angle of rotation.


aq.
A441538

Check if all bolts (A) to (D) have been tightened with a 90° angle of rotation.

i.

All marks (lines) must be horizontal (see figure).



ar.
A441504

Connect and lock all connectors (1) to the injectors.

i.

All connectors (1) must engage audibly.



as.
A441503

Thread in cable channel (3) and install.


at.

Thread in ground cable (2) and install.


au.

Tighten nuts (1).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23250 3.INSTALL FUEL INJECTOR ASSEMBLY (for Rear Side)

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.


a.
A441729

Mount the holder (1) above the bayonet fitting (2) on the injector.


b.

If the holder(1) has a cast lug: Make sure that the holder is installed in the correct position.


c.
A441730

If applicable, note the position of the cast lug:

HINT:

The holder is mounted correctly when the cast lug is located at the rear.



d.
A441731

If applicable, note the position of the cast lug:

NOTICE:
·

Damage to injectors.

Weld seams on the injector may tear due to incorrect distances between the rail and injector so that the injector must be replaced.

-

Insertion of the distance gauge is compulsory.

-

Replace distance gauge, if a thickness of 8.5 mm is no longer given in the distance gauge.




HINT:

The holder is mounted incorrectly when the cast lug (1) is in front.



e.
A441732

Use the special tool (distance gauge) 2 358 022 (1).

SST
09200-WA830  


f.
A441733

Replace E6 bolts.


g.

Mount the injectors with the holders and the bolts (1) on the rail.


h.

Keep the rail on a clean table in such a way that the openings on the rail for the injectors point upwards.

NOTICE:

The electrical injector connections must point to the fuel pressure sensor.



i.

Slide the special tool (distance gauge) 2 358 022 (2) between the holders and the rail onto the injector head.

SST
09200-WA830  


j.

Make sure that the special tool (distance gauge) 2 358 022 (2) rests flat on the retaining bridge.

SST
09200-WA830  


k.

Hand-tighten both bolts (1) evenly until the special tool (distance gauge) 2 358 022 (2) rests flat against the rail and the holder.

SST
09200-WA830  


l.
A441734

Remove the special tool (distance gauge) 2 358 022 (1).

SST
09200-WA830  


m.

Repeat this operation for all injectors.


n.
A441735

Check injectors for loose fit at the rail.


o.

Align the electrical injector connections parallel to the rail.

HINT:

The injectors must move freely.



p.
A441525

Replace bolts (A) to (D).


q.

Attach the rail (1) with the injectors to the cylinder head from the top.


r.

Make sure the injector tips catch the corresponding bore holes in the cylinder head.


s.

Make sure the guides on the injector are properly inserted into the guide bores in the cylinder head.


t.

Press the rail (1) down until a resistance can be felt; join and hand-tighten the bolts (A) and (B).


u.

Set the torque wrench.

Torque:
2.0 N*m (20 kgf*cm, 1 ft.*lbf)


v.

Tighten the bolts (A) and (B) in alternating order by 180° each with the torque wrench until the rail is positioned flush on the cylinder head.

HINT:

The figure shows the rail resting flat against the cylinder head.



w.

Insert bolts (C) and (D).

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques

Non-observance of these requirements may result in leaks and damage.



x.

Tighten E8 bolt (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


y.

Tighten E8 bolt (D).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


z.

Tighten E8 bolt (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


aa.

Tighten E8 bolt (C).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ab.
A441496

Make sure that the rail (1) rests flat against the cylinder head.


ac.
A441526

Attach a socket to an extension.

NOTICE:

Do not use a reversible ratchet or torque wrench.



ad.

Tighten the E6 bolts in pairs ((1) with (2), (3) with (4), (5) with (6)) in alternating order 90° hand-tight.


ae.

Set the torque wrench.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.



af.

Screw the bolts according to the following plan:

i.

Fuel injector 4:


ii.

Tighten E6 bolt (1) at an angle of rotation of 90° +/- 15° with the torque wrench.


iii.

Tighten E6 bolt (2) at an angle of rotation of 90° +/- 15° with the torque wrench.


iv.

Repeat the operations for bolts (1) and (2) until both bolts reach a torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


v.

Fuel injector 5:


vi.

Tighten E6 bolt (3) at an angle of rotation of 90° +/- 15° with the torque wrench.


vii.

Tighten E6 bolt (4) at an angle of rotation of 90° +/- 15° with the torque wrench.


viii.

Repeat the operations for bolts (3) and (4) until both bolts reach a torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ix.

Fuel injector 6:


x.

Tighten E6 bolt (5) at an angle of rotation of 90° +/- 15° with the torque wrench.


xi.

Tighten E6 bolt (6) at an angle of rotation of 90° +/- 15° with the torque wrench.


xii.

Repeat the operations for bolts (5) and (6) until both bolts reach a torque.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



ag.
A441527

Mark all bolts (1) to (6) with a vertical line (see figure).


ah.

Tighten screws using an angle of rotation.

i.

Tighten the E6 bolt (1) with an angle of rotation of 90° +/- 15°.


ii.

Tighten the E6 bolt (2) with an angle of rotation of 90° +/- 15°.


iii.

Tighten the E6 bolt (3) with an angle of rotation of 90° +/- 15°.


iv.

Tighten the E6 bolt (4) with an angle of rotation of 90° +/- 15°.


v.

Tighten the E6 bolt (5) with an angle of rotation of 90° +/- 15°.


vi.

Tighten the E6 bolt (6) with an angle of rotation of 90° +/- 15°.



ai.
A441528

Check if all screws (1) to (6) have been tightened with a 90° +/- 15° angle of rotation.

i.

All marks (lines) must be horizontal (see figure).



aj.
A441529

Unscrew the E8 bolts (A) to (D).

i.

It is imperative that the bolts are unscrewed.

HINT:

When assembling, it is essential to observe screwing sequences and tightening torques.

Non-observance of these requirements may result in leaks and damage.




ak.

Tighten E8 bolt (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


al.

Tighten E8 bolt (D).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


am.

Tighten E8 bolt (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


an.

Tighten E8 bolt (C).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ao.

Mark all bolts (A) to (D) with a vertical line (see figure).


ap.
A441530

Tighten bolts (A) to (D) to a 90° angle of rotation.


aq.
A441531

Check if all bolts (A) to (D) have been tightened with a 90° angle of rotation.

i.

All marks (lines) must be horizontal (see figure).



ar.
A441504

Connect and lock all connectors (1) to the injectors.

i.

All connectors (1) must engage audibly.



as.
A441503

Thread in cable channel (3) and install.


at.

Thread in ground cable (2) and install.


au.

Tighten nuts (1).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23801P 4.INSTALL NO.1 FUEL PIPE SUB-ASSEMBLY