Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388896 REAR CRANKSHAFT OIL SEAL A

B58 ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TIMING CHAIN COVER OIL SEAL

NOTICE:
·

Timing chain cover oil seal damage.

Touching the sealing lip (inner) and applying oil to the timing chain cover oil seal will lead to its destruction.

-

Do not touch the sealing lip (inner) of the timing chain cover oil seal.

-

Do not apply oil to the timing chain cover oil seal.

-

Install the timing chain cover oil seal dry.




a.
A441202

Fit special tool 0 496 137 (11 8 815) on the crankshaft.

SST
09200-WA090  


b.

Carefully remove the timing chain cover oil seal (1) with a rotational movement via special tool 0 496 137 (11 8 815) until the timing chain cover oil seal is in flush contact with the timing gear case.

SST
09200-WA090  

i.

The timing chain cover oil seal must not be tilted in the process.



c.
A441645

Secure special tool 0 494 029 (11 9 182) to the crankshaft using special tool 0 494 031 (11 9 184).


d.
A441230

Connect special tool 2 360 215 to special tool 0 493 881 (11 9 180).

SST
09200-WA060  
09200-WA070  


e.
A441646

Draw in the timing chain cover oil seal using special tools 0 494 028 (11 9 181) and 2 360 215 in conjunction with special tool 0 494 030 (11 9 183).

SST
09200-WA620  
09200-WA060  


f.
A441231

Bolt in the timing chain cover oil seal using special tools 2 360 215 , 0 493 881 (11 9 180) and the tool (1) up to the stop.

SST
09200-WA060  
09200-WA070  


g.
A485751

Using a tap, clean the threads of all of the screw holes.


h.
A485752

Install the tap to the tool holder of special tool 2 285 058.

SST
09212-WA010  


i.
A485753

Using insulating tape, etc., mark the tap insertion depth.

Insertion Depth A:

18 mm



j.
A485754

Twist in the tap in the direction indicated by the arrow until it reaches the specified insertion depth.

Insertion Depth A:

18 mm


HINT:

Make sure that the tap does not contact the timing chain.


NOTICE:
A485755

·

Do not insert the tap beyond the specified insertion depth.

·

Be sure to handle the timing chain and timing gear carefully to avoid damaging them.




k.
A441644

Ensure the correct mounting orientation of the No. 1 crank angle sensor plate (1).


l.

Position the No. 1 crank angle sensor plate (1) on the crankshaft.


Hide 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A444853

Replace bolts (1) to (8).

HINT:

Clean bolt thread.



b.

Position the drive plate and ring gear sub-assembly and apply the bolts (1) to (8) hand-tight.


c.
A445261

Check if the special tool 0 496 595 (11 6 130) is installed and positioned correctly.

SST
09700-WA040  


d.

Install special tool 0 496 595 (11 6 130).

SST
09700-WA040  


e.

Secure drive plate and ring gear sub-assembly with special tool 0 496 595 (11 6 130).

SST
09700-WA040  


f.
A444853

Tighten bolts (1) to (8).

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


g.

Using SST, tighten the bolts an additional 45°.

SST
09900-WA010  

HINT:
C417459C09
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




h.

Remove special tool 0 493 938 (11 9 260).

SST
09200-WA200