Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › INSPECTION AFTER COLLISION
RM3650E _58 Vehicle Interior _079907 SUPPLEMENTAL RESTRAINT SYSTEMS _0397378 INSPECTION AFTER COLLISION G

SUPPLEMENTAL RESTRAINT SYSTEMS  INSPECTION AFTER COLLISION  INSPECTION  


PROCEDURE

Hide 1. INSPECTION AFTER COLLISION

a.

Replace all components that were affected by the accident and check all others!

Check and/or replace following components after airbag deployment:

CAUTION:
·
B475753

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Be sure to correctly follow the removal and installation procedures for the SRS parts.



NOTICE:

If there is any damage or deformation of airbag installation components or the areas they are installed to, do not attempt to repair them. Replace the damaged components with new ones.


Airbag Sensor, Airbag ECU Assembly, Pop up hood
Component to Inspect Procedure
Airbag sensor
1.

Inspect visually for mechanical damage (housing, plug connections). Replace damaged components.

2.

Connect the diagnosis system.

3.

Read fault memory.

4.

Disconnect the vehicle battery and adhere to the waiting period. (at least 30 seconds)

5.

Rectify faults.

6.

Reconnect the vehicle battery and adhere to the waiting period. (at least 10 seconds)

7.

Delete fault memory.

8.

Press the START-STOP button (engine switch).

9.

Turn the START-STOP button (engine switch) off and wait at least 120 seconds.

NOTICE:

No consumers may be switched on during this period such as interior light, radio, etc.


HINT:

Pressing and holding the AUDIO button changes the power source mode to IG OFF.


10.

Press the START-STOP button (engine switch) 3 times within 0.8 seconds to enter Diagnostic (PAD) Mode. (wait for at least 10 seconds)

11.

Delete fault memory.

12.

If you cannot delete the fault memory: Replace the component that is causing the fault.

13.

Replace the airbag ECU assembly in the following cases only:

-

In the case of visible external damage.

-

In the case of a corresponding fault memory entry. (airbag indicator light is illuminated)



Side airbag pressure sensor
Seat position airbag sensor
Airbag ECU assembly
Pedestrian detection chamber assembly
Pop up hood lifter assembly with hood lock assembly

Wire Harness and Connector
Component to Inspect Procedure
Wire harness and connector
1.

Check the wire harness and connectors for damage, replace if necessary.



Seatbelt
Component to Inspect Procedure
Front seat outer belt assembly
1.

Check the components, replace if necessary.


Front seat inner belt assembly
1.

Check the components, replace if necessary.

2.

Check for foreign body, remove it if necessary.



Airbag
Component to Inspect Procedure
Horn button assembly
1.

Check the components, replace if necessary.

HINT:

Also check the steering wheel assembly.


2.

Replace the steering wheel assembly.


Instrument panel passenger without door airbag assembly
1.

Check the components, replace if necessary.

Also check the following component.

-

Instrument panel safety pad assembly

-

Instrument panel reinforcement sub-assembly


2.

Replace the instrument panel safety pad assembly.


Front seat airbag assembly
1.

Check the components, replace if necessary.

Also check the following component.

-

Front seat assembly


2.

Check the seat connection.

3.

Replace the front seat airbag assembly and separate type front seatback cover with pad.


Curtain shield airbag assembly
1.

Check the components, replace if necessary.

Also check the following components.

-

Front pillar garnish

-

Roof headlining assembly

-

Connection/mount (on side frame)



Lower No. 1 instrument panel airbag assembly
1.

Check the components, replace if necessary.

Also check the following component.

-

No. 1 Instrument panel under cover sub-assembly



Lower No. 2 instrument panel airbag assembly
1.

Check the components, replace if necessary.

Also check the following component.

-

No. 2 Instrument panel under cover sub-assembly