SFI SYSTEM > READINESS MONITOR DRIVE PATTERN |
| Steps | Section Titles |
| 1 | Catalyst Monitor (Active Air-Fuel Ratio Control Type) |
| 2 | EVAP System Monitor (Key-Off Type) |
| 3 | Air-Fuel Ratio (A/F) and Heated Oxygen (HO2) Sensor Monitors (Active Air-Fuel Ratio Control Type) |
| 4 | Air-Fuel Ratio (A/F) and Heated Oxygen (HO2) Sensor Heater Monitors (Front A/F and Rear HO2 Sensor Type) |
| CATALYST MONITOR (ACTIVE AIR-FUEL RATIO CONTROL TYPE) |

Preconditions
The monitor will not run unless:
Drive Pattern
Connect an intelligent tester or OBDII scan tool to the DLC3.
Turn the ignition switch ON.
Turn the tester or scan tool ON.
Clear DTCs (where set) (Click here).
Start the engine and warm it up.
Drive the vehicle at between 40 mph and 70 mph (64 km/h and 113 km/h) for at least 10 minutes.
Monitor Status
Check the Readiness Monitor status displayed on the tester or scan tool.
If the status does not switch to COMPL (complete), extend the driving time.
| EVAP SYSTEM MONITOR (KEY-OFF TYPE) |
Preconditions
The monitor will not run unless:
Monitor Conditions
Turn the ignition switch OFF and wait for 6 hours.
Monitor Status
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester or scan tool ON.
Check the Readiness Monitor status displayed on the tester or scan tool.
If the status does not switch to COMPL (complete), restart the engine, make sure that the preconditions have been met, and then perform the Monitor Conditions again.
| AIR-FUEL RATIO (A/F) AND HEATED OXYGEN (HO2) SENSOR MONITORS (ACTIVE AIR-FUEL RATIO CONTROL TYPE) |
Preconditions

Drive Pattern for front A/F sensor and HO2 sensor
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Clear DTCs (Click here).
Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher.
Drive the vehicle at 38 mph (60 km/h) or more for at least 10 minutes.
Change the transmission to 2nd gear.
Accelerate the vehicle to 40 mph (64 km/h) or more by depressing the accelerator pedal for at least 10 seconds.
Soon after performing step (8) above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel-cut control.
Allow the vehicle to decelerate until the vehicle speed declines to less than 6 mph (10 km/h).
Repeat steps from (8) through (10) above at least 3 times in one driving cycle.
Monitor Status
Check the Readiness Monitor status displayed on the tester.
If the status does not switch to COMPL (complete), make sure that the preconditions have been met, and then perform steps from (5) through (11) in Drive Pattern above.
| AIR-FUEL RATIO (A/F) AND HEATED OXYGEN (HO2) SENSOR HEATER MONITORS (FRONT A/F AND REAR HO2 SENSOR TYPE) |

Preconditions
The monitor will not run unless:
Drive Pattern
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester or scan tool ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 10 minutes or more.
Drive the vehicle at 25 mph (40 km/h) or more for at least 2 minutes.
Monitor Status
Check the Readiness Monitor status displayed on the tester or scan tool.
If the status does not switch to COMPL (complete), make sure that the preconditions have been met, and repeat steps through (5) to (7) described in the Drive Pattern above.