DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2123 | VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic)
|
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic)
|
|
| Trouble Areas | ACCEL POS #1 When AP Released | ACCEL POS #2 When AP Released | ACCEL POS #1 When AP Depressed | ACCEL POS #2 When AP Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.0 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 5.0 V |
| Related DTCs | P2120: Accelerator Pedal Position (APP) sensor 1 range check (fluctuating) P2122: APP sensor 1 range check (low voltage) P2123: APP sensor 1 range check (high voltage) P2125: APP sensor 2 range check (fluctuating) P2127: APP sensor 2 range check (low voltage) P2128: APP sensor 2 range check (high voltage) P2138: APP sensor range check (correlation) |
| Required Sensors/Components (Main) | APP sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P2120, P2122, P2125 and P2127 2.0 seconds: P2123, P2128 and P2138 |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Ignition switch | ON |
| Electronic throttle actuator power | ON |
| Either of the following conditions is met: | Condition 1 or 2 |
| 1. VPA1 voltage when VPA2 voltage is V or more | 0.4 V or less |
| 2. VPA1 voltage | 4.8 V or more |
| VPA1 voltage when VPA2 voltage is 0.04 V or more | 0.4 V or less |
| VPA1 voltage | 4.8 V or more |
| Either of the following conditions is met: | Condition 1 or2 |
| 1. VPA2 voltage when VPA1 is 0.04 V or more | 1.2 V or less |
| 2. VPA2 voltage when VPA1 is 0.4 to 3.45 V | 4.8 V or more |
| VPA2 voltage when VPA1 0.04 V or more | 1.2 V or less |
| VPA2 voltage when VPA1 0.4 to 3.45 V | 4.8 V or more |
| Either of following conditions A or B met: | - |
| Condition A | - |
| Difference between VPA1 and VPA 2 voltages | 0.02 V or less |
| Condition B | - |
| VPA1 voltage | 0.4 V or less |
| VPA2 voltage | 1.2 V or less |
| VPA1 voltage | 0.4 V to 4.8 V |
| VPA2 voltage | 1.2 V to 4.8 V |

| 1.READ VALUE OF INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / ACCEL POS #1 and ACCEL POS #2.
Read the value displayed on the tester.
| Accelerator Pedal Operations | ACCEL POS #1 (AP#1) | ACCEL POS #2 (AP#2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A19 Accelerator Pedal Position (APP) sensor connector.
Disconnect the E8 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| VPA (A19-6) - VPA (E8-18) | Below 1 Ω |
| EPA (A19-5) - EPA (E8-20) | |
| VCPA (A19-4) - VCPA (E8-26) | |
| VPA2 (A19-3) - VPA2 (E8-19) | |
| EPA2 (A19-2) - EPA2 (E8-21) | |
| VCP2 (A19-1) - VCP2 (E8-27) |
| Tester Connections | Specified Conditions |
| VPA (A19-6) or VPA (E8-18) - Body ground | 10 kΩ or higher |
| EPA (A19-5) or EPA (E8-20) - Body ground | |
| VCPA (A19-4) or VCPA (E8-26) - Body ground | |
| VPA2 (A19-3) or VPA2 (E8-19) - Body ground | |
| EPA2 (A19-2) or EPA2 (E8-21) - Body ground | |
| VCP2 (A19-1) or VCP2 (E8-27) - Body ground |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A19 APP sensor connector.
Turn the ignition switch ON.
Measure the voltage between the terminals of the E8 ECM connector.
| Tester Connections | Specified Conditions |
| VCPA (E8-26) - EPA (E8-20) | 4.5 to 5.0 V |
| VCP2 (E8-27) - EPA2 (E8-21) |
Reconnect the APP sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 | A |
| No output | B |
|
| ||||
| A | ||
| ||