DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2121 | Difference between VPA and VPA2 exceeds threshold for 0.5 seconds |
|
| Related DTCs | P2121: Accelerator pedal position sensor malfunction |
| Required Sensors/Components (Main) | Accelerator pedal position sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions met: | |
| Difference between VTA sensor 1 voltage (learned value) and VTA2 sensor 2 voltage (learned value) | Less than 0.4 V, or more than 1.2 V |
| 1.READ VALUE USING INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ETCS / ACCEL POS #1 and ACCEL POS #2.
Read the values displayed on the tester.
| Accelerator Pedal Operations | ACCEL POS #1 (AP #1) | ACCEL POS #2 (AP #2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A19 Accelerator Pedal Position (APP) sensor connector.
Disconnect the E8 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| VPA (A19-6) - VPA (E8-18) | Below 1 Ω |
| EPA (A19-5) - EPA (E8-20) | Below 1 Ω |
| VCPA (A19-4) - VCPA (E8-26) | Below 1 Ω |
| VPA2 (A19-3) - VPA2 (E8-19) | Below 1 Ω |
| EPA2 (A19-2) - EPA2 (E8-21) | Below 1 Ω |
| VCP2 (A19-1) - VCP2 (E8-27) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| VPA (A19-6) or VPA (E8-18) - Body ground | 10 kΩ or higher |
| EPA (A19-5) or EPA (E8-20) - Body ground | 10 kΩ or higher |
| VCPA (A19-4) or VCPA (E8-26) - Body ground | 10 kΩ or higher |
| VPA2 (A19-3) or VPA2 (E8-19) - Body ground | 10 kΩ or higher |
| EPA2 (A19-2) or EPA2 (E8-21) - Body ground | 10 kΩ or higher |
| VCP2 (A19-1) or VCP2 (E8-27) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Clear the DTC (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC output) | Proceed to |
| P2121 | A |
| No output | B |
|
| ||||
| A | ||
| ||