Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › KNOCK SENSOR (for 2WD)

KNOCK SENSOR (for 2WD) > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE BATTERY


3. DRAIN ENGINE COOLANT


A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



4. DRAIN ENGINE OIL
  1. Remove the engine under cover seal No. 3.

  1. Remove the oil pan drain plug and drain the engine oil.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. REMOVE ENGINE ASSEMBLY
(Click here)


6. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY



7. REMOVE COOL AIR INLET NO.1
  1. Remove the 2 bolts, then remove the cool air inlet.



8. REMOVE EXHAUST FRONT PIPE ASSEMBLY NO.2
  1. Remove the 2 bolts and 2 nuts, then separate the exhaust front pipe No. 2 from the exhaust front pipe.

  1. Remove the 2 nuts, then separate the exhaust front pipe No. 2 from the exhaust manifold LH.

  1. Separate the insulator, then remove the exhaust front pipe No. 2.



9. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. Remove the 2 nuts, then remove the exhaust front pipe.



10. REMOVE MANIFOLD STAY
  1. Remove the 3 bolts, then remove the exhaust manifold stay.



11. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 6 nuts, then remove the exhaust manifold and gasket.



12. REMOVE INTAKE MANIFOLD
  1. Disconnect the 6 fuel injector connectors.



    A076533E01
  1. Remove the 10 bolts, then remove the intake manifold and gasket.



13. REMOVE WATER BY-PASS JOINT RR
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the heater hose.



    A076534E01
  1. Remove the 2 bolts and 4 nuts, then remove the water by-pass joint RR and 2 gaskets.

  1. Remove the O-ring from the water outlet hose.



14. REMOVE CHAIN VIBRATION DAMPER NO.1
  1. Remove the 2 bolts, then remove the chain vibration damper No. 1.



15. REMOVE CAMSHAFT TIMING GEARS AND NO.2 CHAIN (RH BANK)


G036251E01
  1. While raising the chain tensioner No. 2, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.



    G036252E01
  1. Hold the hexagonal portion of the camshaft with a wrench.

    NOTICE:
    Be careful not to damage the cylinder head and valve lifter with the wrench.

  1. Remove the 2 bolts, then remove the camshaft timing gear, camshaft timing gear assembly and timing chain No. 2.

    NOTICE:
    Do not disassemble the camshaft timing gear assembly.



16. REMOVE CHAIN TENSIONER ASSEMBLY NO.2


G036275E01
  1. Remove the chain tensioner No. 2 bolt, then remove the chain tensioner No. 2 and camshaft timing gear.



17. REMOVE CAMSHAFTS

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.



    A072966E03
  1. Rotate the camshafts counterclockwise using a wrench so that the cam lobes of No. 1 cylinder face in the directions shown in the illustration.



    A072967E05
  1. Using several steps, loosen and remove the 16 bearing cap bolts uniformly in the sequence shown in the illustration.

  1. Remove the 8 bearing caps and 2 camshafts.



18. REMOVE CAMSHAFT BEARING NO.2


19. REMOVE CYLINDER HEAD SUB-ASSEMBLY
  1. Remove the 2 bolts and separate the 2 ground cables.



    A076273E03
  1. Using several steps, uniformly loosen the 8 cylinder head bolts on the cylinder head with a 10 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 8 cylinder head bolts and 8 plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing the bolts in the wrong order.



    A076805E01
  1. Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    NOTICE:
    Be careful not to drop the plate washers into the cylinder head.

    If the cylinder head is difficult to remove, pry between the cylinder head and cylinder block with a screwdriver.



20. DISCONNECT HEATER WATER INLET HOSE


A076171E01


21. REMOVE WATER OUTLET PIPE NO.1


G036164E01
  1. Remove the 4 wire harness clamps.

  1. Remove the 3 bolts and water outlet pipe.



22. REMOVE KNOCK SENSOR


A075662E01
  1. Disconnect the 2 knock sensor connectors.

  1. Remove the 2 bolts and 2 knock sensors.