Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE BATTERY


3. DRAIN ENGINE COOLANT


A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



4. DRAIN ENGINE OIL
  1. Remove the engine under cover seal No. 3.

  1. Remove the oil pan drain plug and drain the engine oil.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the windshield washer hose.

  1. Separate the 2 hood supports.

  1. Remove the 4 bolts, then remove the hood.



6. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH


G036137E02
  1. Disengage the 9 clips, then remove the radiator support to frame seal.



7. REMOVE FAN SHROUD


G036138E01
  1. Disconnect the hose from the radiator reserve tank.



    G036139E01
  1. Remove the 2 cooler hoses from the clamp (with automatic transmission).

  1. Remove the 4 nuts from the fan pulley.

  1. Remove the fan and generator V belt .

  1. Remove the 2 bolts from the fan shroud.

  1. Remove the fan pulley and fan shroud.



8. REMOVE RADIATOR ASSEMBLY


G036140E01
  1. Disconnect the 2 radiator hoses.

  1. Remove the 4 bolts, then remove the radiator.



  1. Disconnect the 2 oil cooler hoses (with automatic transmission).


    G036141



9. REMOVE V-BANK COVER


A075593E01
  1. Remove the 2 nuts, then remove the V-bank cover.



10. REMOVE TRANSMISSION ASSEMBLY

HINT:
Refer to the table below when removing transmission.

Transmission
Drive Type
See Page
Manual Transmission
2WD
Click here
Manual Transmission
4WD
Click here
Automatic Transmission
2WD
Click here
Automatic Transmission
4WD
Click here



11. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
Transmission
See page
RA60
Click here
RA60F
Click here


12. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
Transmission
See page
RA60
Click here
RA60F
Click here


13. REMOVE FAN PULLEY


14. REMOVE VANE PUMP ASSEMBLY


A076444E02
  1. Disconnect the power steering pressure switch connector.

  1. Remove the 2 bolts, then separate the vane pump.

    NOTICE:
    Do not hit the pulley with other parts when separating the vane pump.

    HINT:
    The vane pump is suspended securely.



15. REMOVE GENERATOR ASSEMBLY


A076407E01
  1. Disconnect the wire harness.

    1. Remove the bolt and wire harness stay.

    2. Disconnect the connector from the generator assembly.

    3. Remove the terminal cap and nut.

    4. Disconnect the wire harness from terminal B.



    A076408E01
  1. Remove the 2 bolts, then separate the wire harness clamp bracket from the generator assembly.



    A076409E01
  1. Remove the 2 bolts, then remove the generator assembly.



16. SEPARATE COOLER COMPRESSOR ASSEMBLY


G036154E01
  1. Remove the bolt, then separate the suction hose sub-assembly.



    G036155E01
  1. Disconnect the cooler compressor assembly connector.

  1. Remove the 4 bolts, then separate the cooler compressor assembly from the V-ribbed belt tensioner assembly.



17. DISCONNECT NO.1 FUEL PIPE SUB-ASSEMBLY


A121823E01
  1. Remove the fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



18. DISCONNECT NO.2 FUEL PIPE SUB-ASSEMBLY


A121824E01
  1. Remove the fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



19. DISCONNECT HEATER WATER INLET HOSE


20. DISCONNECT HEATER WATER OUTLET HOSE


21. REMOVE INTAKE AIR SURGE TANK


A076500E02
  1. Disconnect the 2 water by-pass hoses.



    A075644E01
  1. Disconnect the fuel vapor feed hose.



    A075645E01
  1. Disconnect the ventilation hose.



    A075646E01
  1. Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and hose clamp.



    G036170E01
  1. Remove the nut, then separate the clutch flexible hose bracket from the surge tank stay (with Manual Transmission).



    A076501E01
  1. Remove the 2 bolts and throttle body bracket.



    A076502E01
  1. Remove the bolt and oil baffle plate.

  1. Remove the 4 bolts and 2 surge tank stays.



    A075648E02
  1. Remove the 2 nuts.

  1. Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and gasket.



22. SEPARATE ENGINE WIRE
  1. Remove the glove compartment door.

  1. Remove the instrument panel finish panel sub-assembly lower RH.

  1. Disconnect the 5 connectors from the ECM.

  1. Disconnect the 2 connectors from four wheel drive ECU (4WD only).

  1. Pull the wire harness into the engine room.

  1. Disconnect the front differential connector (4WD only).



    G037710E03
  1. Disconnect the 3 connectors from the engine room relay block.

  1. Remove the nut, then separate the engine wire from the engine room relay block.



23. SEPARATE NO.2 ENGINE WIRE
  1. Disconnect the ground cable from the cylinder block.



24. REMOVE ENGINE ASSEMBLY


A072941E02
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No:
    Engine hanger No. 1 12281-31070
    Engine hanger No. 2 12282-31050
    Bolt 90119-08177

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



    G036196E01
  1. Remove the 4 bolts and 4 nuts, and separate the engine mounting brackets from the frame brackets.

  1. Lift the engine out of the vehicle carefully.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.

  1. Place the engine onto a working bench.



25. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


A076326E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G036171E02
  1. Remove the 8 bolts, then remove the flywheel and 2 spacers.



26. REMOVE DRIVE PLATE & RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


A076326E03
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A076327E01
  1. Remove the 8 bolts, then remove the drive plate and 2 spacers.



27. REMOVE HEATER WATER INLET HOSE


G036201E01


28. REMOVE HEATER WATER OUTLET HOSE


G036202E01


29. REMOVE VENTILATION HOSE


G036200E01


30. REMOVE NO.2 VENTILATION HOSE


G036199E01


31. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Remove the 6 nuts, exhaust manifold and gasket.



32. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Remove the 6 nuts, exhaust manifold and gasket.



33. REMOVE FRONT NO.1 ENGINE MOUNTING BRACKET RH


G036197E01
  1. Remove the 4 bolts, then remove the engine mounting bracket RH.



34. REMOVE FRONT NO.1 ENGINE MOUNTING BRACKET LH


G036198E01
  1. Remove the 3 bolts, then remove the engine mounting bracket LH.



35. REMOVE NO.2 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the 2 bolts, then remove the 2 idler pulleys.



36. REMOVE NO.1 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the bolt, then remove the idler pulley.



37. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


A076445E01
  1. Remove the 5 bolts, then remove the V-ribbed belt tensioner.



38. REMOVE WATER INLET


A076319E02
  1. Remove the 3 nuts, then remove the water inlet with thermostat and gasket.



39. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
  1. Remove the 3 bolts and 2 nuts, then remove the oil filter bracket and gasket.



40. REMOVE INTAKE MANIFOLD
  1. Disconnect the 6 fuel injector connectors.



    A076533E01
  1. Remove the 10 bolts, then remove the intake manifold and gasket.



41. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


G036118E01
  1. Disconnect the 2 connectors.

  1. Remove the 2 bolts, then remove the 2 camshaft timing oil control valves.



42. REMOVE WATER BY-PASS JOINT RR
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the heater hose.



    A076534E01
  1. Remove the 2 bolts and 4 nuts, then remove the water by-pass joint RR and 2 gaskets.

  1. Remove the O-ring from the water outlet hose.



43. REMOVE OIL FILTER CAP SUB-ASSEMBLY


44. REMOVE OIL FILLER CAP HOUSING
  1. Remove the 2 nuts, oil filler cap housing and gasket.



45. REMOVE IGNITION COIL ASSEMBLY


G036133E01
  1. Disconnect the 6 connectors.

  1. Remove the 6 bolts, then remove the 6 ignition coils.



46. REMOVE SPARK PLUG


47. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY