Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



C121776E01

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltage column. The illustration above can be used as a reference to identify the ECM terminal locations.


Symbols (Terminals No.)
Wiring Colors
Terminal Descriptions
Conditions
STD Voltages
BATT (E8-3) - E1 (E4-3)
L - BR
Battery (for measuring battery voltage and for ECM memory)
Always
9 to 14 V
+BM (E8-7) - E1 (E4-3)
LG - BR
Power source of throttle motor
Always
9 to 14 V
IGSW (E8-9) - E1 (E4-3)
O - BR
Ignition switch
Ignition switch ON
9 to 14 V
+B (E8-1) - E1 (E4-3)
B - BR
Power source of ECM
Ignition switch ON
9 to 14 V
MREL (E8-8) - E1 (E4-3)
G-W - BR
EFI relay
Ignition switch ON
9 to 14 V
VC (E4-18) - E2 (E4-28)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.0 V
VTA1 (E4-20) - E2 (E4-28)
G-B - BR
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
VTA1 (E4-20) - E2 (E4-28)
G-B - BR
Throttle position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully depressed
3.3 to 4.9 V
VTA2 (E4-19) - E2 (E4-28)
G-W - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
VTA2 (E4-19) - E2 (E4-28)
G-W - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
4.5 to 5.0 V
VPA (E8-18) - EPA (E8-20)
R-Y - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
VPA (E8-18) - EPA (E8-20)
R-Y - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
VPA2 (E8-19) - EPA2 (E8-21)
GR-B - R-B
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
VPA2 (E8-19) - EPA2 (E8-21)
GR-B - R-B
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
VCPA (E8-26) - EPA (E8-20)
R - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.0 V
VCP2 (E8-27) - EPA2 (E8-21)
L-W - R-B
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.0 V
VG (E5-28) - E2G (E5-30)
R-Y - R-W
Mass air flow meter
Idling, Shift position P or N, A/C switch OFF
0.5 to 3.0 V
THA (E5-29) - E2 (E4-28)
R-L - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
THW (E4-32) - E2 (E4-28)
Y-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
#10 (E5-6) - E01 (E4-7)
#20 (E5-5) - E01 (E4-7)
#30 (E5-2) - E01 (E4-7)
#40 (E5-1) - E01 (E4-7)
R-L - W-B
B - W-B
R - W-B
G - W-B
Injector
Ignition switch ON
9 to 14 V
#10 (E5-6) - E01 (E4-7)
#20 (E5-5) - E01 (E4-7)
#30 (E5-2) - E01 (E4-7)
#40 (E5-1) - E01 (E4-7)
R-L - W-B
B - W-B
R - W-B
G - W-B
Injector
Idling
Pulse generation
(see waveform 1)
IGT1 (E4-17) - E1 (E4-3)
IGT2 (E4-16) - E1 (E4-3)
IGT3 (E4-15) - E1 (E4-3)
IGT4 (E4-14) - E1 (E4-3)
P - BR
P-L - BR
LG - BR
LG-B - BR
Ignition coil with igniter
(ignition signal)
Idling
Pulse generation
(see waveform 2)
IGF1 (E4-23) - E1 (E4-3)
W-R - BR
Ignition coil with igniter
(ignition confirmation signal)
Ignition switch ON
4.5 to 5.0 V
IGF1 (E4-23) - E1 (E4-3)
W-R - BR
Ignition coil with igniter
(ignition confirmation signal)
Idling
Pulse generation
(see waveform 2)
G2 (E4-26) - NE- (E4-34)
L - G
Camshaft position sensor
Idling
Pulse generation
(see waveform 3)
NE+ (E4-27) - NE- (E4-34)
R - G
Crankshaft position sensor
Idling
Pulse generation
(see waveform 3)
FC (E8-25) - E1 (E4-3)
L-B - BR
Fuel pump control
Ignition switch ON
9 to 14 V
FC (E8-25) - E1 (E4-3)
L-B - BR
Fuel pump control
Idling
Below 1.5 V
M+ (E4-5) - ME01 (E5-3)
P - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 4)
M- (E4-4) - ME01 (E5-3)
L - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 5)
A1A+ (E4-21) - E1 (E4-3)
P - BR
A/F sensor
Always (Ignition switch ON)
3.3 V*1
A1A- (E4-31) - E1 (E4-3)
L - BR
A/F sensor
Always (Ignition switch ON)
3.0 V*1
OX1B (E4-25) - E2 (E4-28)
W - BR
Heated oxygen sensor
Engine speed maintained 2,500 rpm for 2 minutes after warming up sensor
Pulse generation
(see waveform 6)
HA1A (E4-1) - E04 (E5-7)
R - W-B
A/F sensor heater
Idling
Below 3.0 V
HA1A (E4-1) - E04 (E5-7)
R - W-B
A/F sensor heater
Ignition switch ON
9 to 14 V
HT1B (E4-2) - E03 (E5-4)
G - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
HT1B (E4-2) - E03 (E5-4)
G - W-B
Heated oxygen sensor heater
Ignition switch ON
9 to 14 V
KNK1 (E4-29) - EKNK (E4-30)
B - W
Knock sensor
Maintain engine speed 4,000 rpm after warming up engine
Pulse generation
(see waveform 7)
OC1+ (E4-13) - OC1- (E4-12)
L-W - W
Camshaft timing oil control valve (OCV)
Idling
Pulse generation
(see waveform 8)
PRG (E5-23) - E01 (E4-7)
Y - W-B
Purge VSV
Ignition switch ON
9 to 14 V
PRG (E5-23) - E01 (E4-7)
Y - W-B
Purge VSV
Idling
Pulse generation
(see waveform 9)
VPMP (E8-5) - E1 (E4-3)
V-W - BR
Vent valve
(built into canister pump module)
Ignition switch ON
9 to 14 V
MPMP (E8-6) - E1 (E4-3)
G - BR
Leak detection pump
(built into canister pump module)
  1. Leak detection pump OFF
0 to 3 V
MPMP (E8-6) - E1 (E4-3)
G - BR
Leak detection pump
(built into canister pump module)
  1. Leak detection pump ON
9 to 14 V
PPMP (E8-31) - E2 (E4-28)
GR - BR
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3 to 3.6 V
STA (E8-12) - E1 (E4-3)
B-Y - BR
Starter signal
Shift position N, Ignition switch START
5.5 V or more
STP (E7-4) - E1 (E4-3)
L - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
STP (E7-4) - E1 (E4-3)
L - BR
Stop light switch
Brake pedal released
Below 1.5 V
ST1- (E8-16) - E1 (E4-3)
V-W - BR
Stop light switch
Ignition switch ON, Brake pedal depressed
Below 1.5 V
ST1- (E8-16) - E1 (E4-3)
V-W - BR
Stop light switch
Ignition switch ON, Brake pedal released
7.5 to 14 V
W (E7-30) - E01 (E4-7)
BR - W-B
MIL
Idling
9 to 14 V
W (E7-30) - E01 (E4-7)
BR - W-B
MIL
Ignition switch ON
Below 3.5 V
ELS (E8-15) - E1 (E4-3)
G - BR
Electric load
Tail light switch ON
7.5 to 14 V
ELS (E8-15) - E1 (E4-3)
G - BR
Electric load
Tail light switch OFF
0 to 1.5 V
ELS2 (E7-20) - E1 (E4-3)
B-W - BR
Electric load
Vehicle stationary, Voltage inverter outputs more than 100 W
9 to 14 V
ELS2 (E7-20) - E1 (E4-3)
B-W - BR
Electric load
Vehicle stationary, Voltage inverter outputs 100 W or less
0 to 1.5 V
TACH (E7-1) - E1 (E4-3)
B-W - BR
Engine speed
Idling
Pulse generation
(see waveform 10)
SPD (E7-8) - E1 (E4-3)
V-W - BR
Speed signal from combination meter
Driving at 12 mph (20 km/h)
Pulse generation
(see waveform 11)
TC (E7-17) - E1 (E4-3)
P-B - BR
Terminal TC of DLC 3
Ignition switch ON
9 to 14 V
PSW (E5-32) - E1 (E4-3)
G-W - BR
Power steering oil pressure switch
While turning steering wheel
Below 1.5 V
F/PS (E7-32) - E1 (E4-3)
R - BR
Airbag sensor assembly
Idling with warm engine
Pulse generation
(see waveform 12)
NSW (E8-30) - E1 (E4-3)
V - BR
Park/Neutral switch signal
IG switch ON and shift lever P or N position
Below 1 V
NSW (E8-30) - E1 (E4-3)
V - BR
Park/Neutral switch signal
IG switch ON and shift lever except P and N
9 to 14 V
*2 CANH (E7-33) - E1 (E4-3)
B - BR
Communication signal with other components
Ignition switch ON
Pulse generation
(see waveform 13)
*2 CANL (E7-34) - E1 (E4-3)
W - BR
Communication signal with other components
Ignition switch ON
Pulse generation
(see waveform 14)
AIRV (E4-24) - E1 (E4-3)
R-W - BR
Air switching valve for secondary air injection system
Idling
9 to 14 V
AIRP (E4-11) - E1 (E4-3)
Y-R - BR
Air pump control
Idling
9 to 14 V
AIDI (E5-20) - E1 (E4-3)
G-R - BR
Diagnostic information signal for air injection system
Air injection system operates
Pulse generation
(see waveform 15)
AIP (E5-22) - E2 (E4-28)
GR - BR
Secondary air injection system pressure signal
Ignition switch ON
4.5 to 5.0 V
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
*2: Only for the vehicle equipped with VSC (Click here).

WAVEFORM 1
Fuel injector
A093279E08
ECM Terminal Names
Between #10 (to 40) and E01
Tester Ranges
20 V/DIV, 20 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 2
A093278E16
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)
    ECM Terminal Names
    (a) Between IGT (1 to 4) and E1
    (b) Between IGF1 and E1
    Tester Ranges
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 3
A063955E10
  1. Camshaft position sensor

  2. Crankshaft position sensor
    ECM Terminal Names
    (a) Between G2+ and NE-
    (b) Between NE+ and NE-
    Tester Ranges
    5 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 4
Throttle actuator positive terminal
A093274E12
ECM Terminal Names
Between M+ and ME01
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 5
Throttle actuator negative terminal
A093275E11
ECM Terminal Names
Between M- and ME01
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 6
Heated oxygen sensor
A088863E14
ECM Terminal Names
Between OX1B and E2
Tester Ranges
0.2 V/DIV, 200 msec./DIV
Conditions
Engine speed maintained 2,500 rpm for 2 minutes after warming up engine

HINT:
In the DATA LIST, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 7
Knock sensor
A082985E13
ECM Terminal Names
Between KNK1 and EKNK
Tester Ranges
0.01 to 10 V/DIV, 0.01 to 10 msec./DIV
Conditions
Engine speed maintained 4,000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine rpm increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 8
Camshaft timing oil control valve (OCV)
A093229E10
ECM Terminal Names
Between OC1+ and OC1-
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 9
EVAP VSV
A093230E05
ECM Terminal Names
Between PRG and E01
Tester Ranges
5 V/DIV, 50 msec./DIV
Conditions
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10
Engine speed signal
A093225E09
ECM Terminal Names
Between TACH and E1
Tester Ranges
5 V/DIV, 10 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 11
Vehicle speed signal
A093224E11
ECM Terminal Names
Between SPD and E1
Tester Ranges
5 V/DIV, 20 msec./DIV
Conditions
Driving at 12 mph (20 km/h)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 12
Airbag sensor assembly
A093227E05
ECM Terminal Names
Between F/PS and E1
Tester Ranges
5 V/DIV, 500 msec./DIV
Conditions
Idling with warm engine

WAVEFORM 13
CAN communication signal (reference)
A086154E09
ECM Terminal Names
Between CANH and E1
Tester Ranges
1 V/DIV, 10 μs/DIV
Conditions
Ignition switch ON

WAVEFORM 14
CAN communication signal (reference)
A086155E10
ECM Terminal Names
Between CANL and E1
Tester Ranges
1 V/DIV, 10 μs/DIV
Conditions
Ignition switch ON

WAVEFORM 15
Terminal DI of air injection control driver
G037721E04
ECM Terminal Names
Between AIDI and E1
Tester Ranges
5 V/DIV, 100 ms/DIV
Conditions
Performing ACTIVE TEST using intelligent tester (air injection system)

HINT:
The wavelength changes when the air injection control driver detects malfunctions in the air injection system .