Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

for Preparation Click here


DESCRIPTION

Refer to DTC P0335 .

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviations in crankshaft and camshaft position sensor signals
(2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the valve timing by using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Oil Control Valve (OCV) and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft. The ECM calibrates the intake valve timing by setting the intake camshaft to the most retarded angle while the engine is idling. The ECM closes the OCV to retard the cam. The ECM stores this value as the VVT learning value. When the difference between the target and actual intake valve timings is 5°CA (Crankshaft Angle) or less, the ECM stores it.
    If the VVT learning value matches the following conditions, the ECM determines the existence of a malfunction in the VVT system, and sets the DTC.
  1. VVT learning value: Less than 33°CA, or more than 51°CA.
  1. Above condition continues for 18 seconds or more.
  1. This DTC indicates that the intake camshaft has been installed toward the crankshaft at an incorrect angle, caused by factors such as the timing chain having jumped a tooth.
    This monitor begins to run after the engine has idled for 5 minutes.

MONITOR STRATEGY


Related DTCs
P0016: Camshaft timing (bank 1) misalignment
Required Sensors/Components (Main)
VVT actuator
Required Sensors/Components (Related)
Camshaft position sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
Within 60 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0011 (VVT system 1 - advance)
P0012 (VVT system 1 - retard)
P0115 - P0118 (ECT sensor)
Engine RPM
550 to 1,000 rpm

TYPICAL MALFUNCTION THRESHOLDS


Valve timing when camshaft retarded maximum
Less than 33°, or more than 51°

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  2. After replacing the ECM or adjusting intake valve timing, confirm that the DTC output does not recur.
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the tester ON.
    4. Clear DTCs (Click here).
    5. Switch the ECM from normal mode to check mode using the tester (Click here).
    6. Start the engine and warm it up.
    7. Allow the engine to idle for 1 minute or more, and then drive the vehicle for 1 minute or more.
    8. Confirm that no DTC is set, using the tester.

1.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
G038285E01
  1. Remove the cylinder head cover.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the point marks on the camshaft timing gears are as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°) and align the marks as above.

OK:
Point marks on camshaft timing gears are aligned as shown in illustration.

  1. Reinstall the cylinder head cover.



NG
ADJUST VALVE TIMING
OK

REPLACE ECM