Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CENTER AIRBAG SENSOR ASSEMBLY

CENTER AIRBAG SENSOR ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is turned to OFF.

  1. Check that the cable is disconnected from the battery negative terminal.

    CAUTION:
    After removing the terminal, wait for at least 90 seconds before starting the operation.

  1. Provisionally install the air bag sensor assembly center with the 3 bolts.

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, make sure that the SRS wiring dose not interfere with any other parts and that it is not pinched between other parts.

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

  1. Check that there is no slack in the installation parts of the center airbag sensor assembly.

  1. Connect the holder (with connectors) to the center airbag sensor assembly.

  1. Check that the waterproof sheet is properly set.



2. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)


B085776E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085775E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



3. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)


    B085812E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085811E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



4. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    B085814E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



5. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)


    B085777E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.



6. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B085773E01
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.



7. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



8. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Engage the 4 clips and claw, and remove the console upper panel sub-assembly.



9. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085769E01
  1. Engage the 6 clips and claw, and remove the console upper rear panel.

  1. Install the shift knob.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



11. INSPECT SRS WARNING LIGHT
(Click here)