Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0973    Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)

DTC    P0974    Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)

DTC    P0976    Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)

DTC    P0977    Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2)

for Preparation Click here


DESCRIPTION

Shifting from 1st to 4th is performed in combination with the ON and OFF operation of the shift solenoid valves No. 1 and No. 2 which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valve to allow the vehicle to be driven smoothly. (In case of an open or short circuit, the ECM stops sending current to the circuit.)
Fail-safe functions (Click here)

DTC No.
DTC Detection Conditions
Trouble Areas
P0973
ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated. (1-detection logic)
  1. Short in shift solenoid valve S1 circuit
  2. Shift solenoid valve S1
  3. ECM
P0974
ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated. (1-detection logic)
  1. Open in shift solenoid valve S1 circuit
  2. Shift solenoid valve S1
  3. ECM
P0976
ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated. (1-trip detection logic)
  1. Short in shift solenoid valve S2 circuit
  2. Shift solenoid valve S2
  3. ECM
P0977
ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated. (1-trip detection logic)
  1. Open in shift solenoid valve S2 circuit
  2. Shift solenoid valve S2
  3. ECM

MONITOR DESCRIPTION

The ECM controls the gearshift by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in either shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores a DTC. And the ECM performs the fail-safe function and turns the other shift solenoid valves in good condition "ON/OFF". (In case of an open or short circuit, the ECM stops sending current to the circuit.)

MONITOR STRATEGY


P0973, P0974: 
Related DTCs
P0973: Shift solenoid valve S1/Range check (Low resistance)
P0974: Shift solenoid valve S1/Range check (High resistance)
Required sensors/Components
Shift solenoid valve S1
Frequency of operation
Continuous
Duration
0.1 seconds x 2 (times) or more
MIL operation
Immediate
Sequence of operation
None

P0976, P0977: 
Related DTCs
P0976: Shift solenoid valve S2/Range check (Low resistance)
P0977: Shift solenoid valve S2/Range check (High resistance)
Required sensors/Components
Shift solenoid valve S2
Frequency of operation
Continuous
Duration
0.1 seconds x 2 (times) or more
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Range check (Low resistance)
P0973: Range check (Low resistance) 
The monitor will run whenever the following DTCs are not present.
None
Solenoid
ON

P0974: Range check (High resistance) 
The monitor will run whenever the following DTCs are not present.
None
Solenoid
OFF

P0976: Range check (Low resistance) 
The monitor will run whenever the following DTCs are not present.
None
Solenoid
ON

P0977: Range check (High resistance) 
The monitor will run whenever the following DTCs are not present.
None
Solenoid
OFF

TYPICAL MALFUNCTION THRESHOLDS


P0973: Range check (Low resistance) 
Intelligent power MOS diagnosis fail signals detected while the solenoid is operated
Fail: Solenoid resistance 8 Ω or less

P0974: Range check (High resistance) 
Intelligent power MOS diagnosis fail signals detected while the solenoid is not operated
Fail: Solenoid resistance 100 kΩ or more

P0976: Range check (Low resistance) 
Intelligent power MOS diagnosis fail signals detected while the solenoid is operated
Fail: Solenoid resistance 8 Ω or less

P0977: Range check (High resistance) 
Intelligent power MOS diagnosis fail signals detected while the solenoid is not operated
Fail: Solenoid resistance 100 kΩ or more

COMPONENT OPERATING RANGE


P0973, P0974: 
Shift solenoid valve S1 resistance
11 to 15 Ω at 20°C (68°F)

P0976, P0977: 
Shift solenoid valve S2 resistance
11 to 15 Ω at 20°C (68°F)

WIRING DIAGRAM


C121781E01


INSPECTION PROCEDURE


HINT:
  1. The shift solenoid valve S1 or S2 is turned on/off normally when the shift lever is in the D position:

Gearshift controlled by ECM
1st
2nd
3rd
4th
Shift solenoid valve S1
ON
ON
OFF
OFF
Shift solenoid valve S2
OFF
ON
ON
OFF

1.INSPECT TRANSMISSION WIRE (S1/S2)
C121788E01
  1. Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4 - Body ground
    11 to 15 Ω at 20°C (68°F)
    8 - Body ground
    11 to 15 Ω at 20°C (68°F)



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
C095812E39
  1. Connect the transmission connector to the transmission.

  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E5-9 (S1) - Body ground
    11 to 15 Ω at 20°C (68°F)
    E5-8 (S2) - Body ground
    11 to 15 Ω at 20°C (68°F)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM 

3.INSPECT SHIFT SOLENOID VALVE (S1/S2)
G022784E02
  1. Remove the shift solenoid valve S1 or S2.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S1) - Solenoid Body (S1)
    11 to 15 Ω at 20°C (68°F)
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ω at 20°C (68°F)

  1. Connect positive (+) lead to the terminal of the solenoid connector, negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE (S1/S2)
OK

REPAIR OR REPLACE TRANSMISSION WIRE